Table of Contents
Advertisement
8-7. Timer Operation
• When setting the timer, make sure the current time on the remote control is accurate.
• The timer's clock can only be set when the display of the remote control is ON.
• After setting the timer, put the remote control in a place where its signal will reach the
receiver of the indoor unit. (When the time set for the timer is reached, a signal is sent
from the remote control to Start/Stop the unit.)
Using the Timer
1.
Press either
if you press
The time last set on the timer is displayed.
"--:--" indicates time to change the batteries.
2.
Press either
Every time you press
If you press and hold the button, the time changes quickly.
3.
After setting the timer, if you press
indicating settings are complete.
After the timer setting is displayed for three seconds, the display reverts to the current time.
Combining ON and OFF Timers
• Setting the ON and OFF timers, respectively.
Checking the timer setting
• If you press either
• When no timer setting has been made, it displays --:--. (Initial Setting)
Changing a timer setting
• Press
/
for the
Canceling a timer setting
• If you press [CANCEL], the timer setting is canceled.
• If you wish to cancel the setting for either the
time is displayed, press [CANCEL].
Using the same timer setting every day
• If you press
for 2 or more seconds, "
same time every day.
• If you press
again for two seconds or more, "
8-8. Adjusting the Wind Direction
• Never try to manually move the fl ap (up-down wind direction plate) that is operated by the remote control.
• When the unit stops, the fl ap (up-down wind direction plate) automatically faces downwards.
• When the unit is in heating standby, the fl ap (up-down wind direction plate) faces upward. Also, bear in mind that the fl ap
starts swinging after the heating standby mode is released, but the display on the remote control indicates
Auto Flap during standby heating as well.
RCS-SH80BG.WL / RCS-TRP80BG.WL / RCS-SS80BG.WL / RCS-XM18BG.WL / Indoor Unit (K type)
Setting the Wind Direction
While the unit is operating, every time you press
changes.
Setting Flap to Swing
If you press
to set the fl ap (up-down wind direction plate) in its most downward
facing position, and then press
automatically up and down.
Stopping Flap Swing
If you press
again while the fl ap is swinging, you can stop the fl ap from swinging
and set it in place as desired. Thereafter, if you press
starting from the most upward position.
• When the unit is in the Cool or Dry modes, the fl ap cannot stop facing downwards.
If you try to stop the fl ap from swinging while it is facing downwards, it will continue
8
moving until it is in the third position from the top.
RCS-BH80BG.WL
The available functions differ depending on the indoor unit being used. The wind
direction cannot be set via remote control for any models other than those noted below.
For more information, please refer to the users' manual that came with your indoor unit.
Four-direction Ceiling Cassette Models, Bi-directional Ceiling Cassette Models,
Unidirectional Cassette Models for High Ceilings, Ceiling Suspended Models, Wall Models
Please refer to Setting the Wind Direction and Stopping Flap Swing.
/
of the
or
, and while the time is being displayed,
/
again, a scheduled time can be set.
/
of the
or
and set the timer to the desired time.
/
, the time changes in 10 minutes increments.
, the time you set changes to a steady display,
/
for the
or the
or the
, and then when the timer setting is displayed, press
" is displayed and the ON timer or the OFF timer will operate the unit at the
again,
is displayed and the fl ap swings
, the scheduled time is displayed for four seconds.
or the
timer, press
" goes off and the timer operates just once.
, the direction the fl ap faces
, you can set the wind direction
8-6
3
/
for the timer again.
/
or the desired timer and when the scheduled
In the Heat Mode
Please face the fl ap (up-down
wind direction plate) downwards.
If it faces upwards, the warm air
will not reach the fl oor level.
In the Cool and Dry Modes
Please face the fl ap (up-down wind
direction plate) upwards. If the plate
faces downwards, condensation
may form and drip from around
the air outlet.
In the Fan Mode
Initial Setting
Displays with Swing Stopped
Fan/Heat Modes
1,2
Initial Setting
Initial Setting
In All Modes
Moves Constantly
Cool/Dry Modes
Hide quick links:
Advertisement
Table of Contents
