PIONEER Service Manual. A subscription to, or additional copies Also test with plug reversed of, PIONEER Ser vice Manual may be obtained at a (Using AC adapter Earth nominal charge from PIONEER. plug as required)
TUNE QUIET/ (ADG7021) MIDNIGHT FOLDER FOLDER PROGRAM REPEAT RANDOM CLEAR TEST TONE CH LEVEL TIMER ENTER DISPLAY DIMMER DISC 1 DISC 2 DISC 3 CD MODE SHIFT DISC 4 DISC 5 DISC SKIP 5.1ch DVD SURROUND SYSTEM u163 XV-HTD330 http://www.xiaoyu163.com...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING L 13942296513 KCXJ Type Only FRONT u163 XV-HTD330 http://www.xiaoyu163.com...
Page 7
Operating Instructions ARB7283 Packing Case HTM AHD8170 (English) Operating Instructions See Contrast table(2) (French) (2) CONTRAST TABLE XV-HTD330/KUXJ and KCXJ are constructed the same except for the following : Mark Symbol and Description XV-HTD330/KUXJ XV-HTD330/KCXJ Operating Instructions Not used ARC7494 (French)
3 7 63 1515 0 SSRB ASSY (AWU8155) TRSB ASSY (AWU8154) L 13942296513 TRAY MOTOR DXM1143 LOMB ASSY (AWU8156) CARRIAGE MOTOR (LOADING) : VXM1033 CN123 u163 : The power supply is shown with the marked box. A B C XV-HTD330 http://www.xiaoyu163.com...
Page 21
: FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE PICKUP ASSY-S (OXX8005) (RF) (RF) (RF) (RF) (RF) (RF) CN121 L 13942296513 SSIB ASSY (AWU8157) SPINDLE MOTOR : VXM1099 CN122 STEPPING MOTOR : VXM1101 u163 XV-HTD330 http://www.xiaoyu163.com...
Page 23
: DVD DATA SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE (DVD) (DVD) L 13942296513 R1011 R1012 R1013 (TO CHASSIS GND) u163 : The power supply is shown with the marked box. XV-HTD330 http://www.xiaoyu163.com...
Page 27
: VIDEO SIGNAL ROUTE (Cb/B) : S VIDEO SIGNAL ROUTE (Y) : S VIDEO SIGNAL ROUTE (Y) (C/V) : S VIDEO SIGNAL ROUTE (C/V) u163 (AD) : AUDIO DATA SIGNAL ROUTE : The power supply is shown with the marked box. XV-HTD330 http://www.xiaoyu163.com...
3.8 FM/AM TUNER MODULE 3 7 63 1515 0 FM/AM TUNER MODULE (AXQ7228) FM FRONT END (FM) (FM) (FM) L 13942296513 (FM) (FM) (AM) (AM) (AM) AM RF TUNING BLOCK (FM) (AM) OSC : 981 - 2052kHz 9k step u163 XV-HTD330 http://www.xiaoyu163.com...
Page 29
: The power supply is shown with the marked box. (TX) : TUNER AUDIO SIGNAL ROUTE (AM) : AM SIGNAL ROUTE (FM) : FM SIGNAL ROUTE (AM) (TX) (FM) (TX) (TX) (TX) L 13942296513 (FM) (FM) (TX) (AM) L201 ATE7003 u163 XV-HTD330 http://www.xiaoyu163.com...
3.9 AF ASSY (1/4) 3 7 63 1515 0 AF ASSY (AWU8069) L 13942296513 (FL) (FL) (SL) (SW) u163 (AD) (AD) (AD) (FL) (FL) (FL) XV-HTD330 http://www.xiaoyu163.com...
Page 31
: S VIDEO SIGNAL ROUTE (Y) (C/V) : S VIDEO SIGNAL ROUTE (C/V) : The power supply is shown with the marked box. CN5721 (AD) L 13942296513 (C/V) (Cr/R) (Cb/B) (CY/G) (AD) (AD) u163 2/4-4/4 (AD) 2/4, 3/4 CN8001 XV-HTD330 http://www.xiaoyu163.com...
: AUDIO SIGNAL ROUTE (Center ch) (SW) : AUDIO SIGNAL ROUTE (Sub Woofer ch) u163 • NOTE FOR FUSE REPLACEMENT FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION - L M O REPLACE WITH SAME TYPE AND RATINGS ONLY. XV-HTD330 http://www.xiaoyu163.com...
Page 45
(CY/G) : VIDEO SIGNAL ROUTE (CY/G) : S VIDEO SIGNAL ROUTE (Y) (C/V) (PB/B) : S VIDEO SIGNAL ROUTE (C/V) : VIDEO SIGNAL ROUTE (PB/B) u163 : The power supply is shown with the marked box. SYSTEM DOWNLOAD XV-HTD330 http://www.xiaoyu163.com...
3.17 DISPLAY, JOG, DISC KEY, HP MIC and FUNCTION KEY ASSYS 3 7 63 1515 0 L 13942296513 (FL) (FL) (FL) (FL) JOG ASSY (AWU8065) u163 DISC KEY ASSY (AWU8063) P Q R XV-HTD330 http://www.xiaoyu163.com...
Page 47
L 13942296513 (FL) HP MIC ASSY (AWU8064) : AUDIO SIGNAL ROUTE (Front L ch) (FL) (FL) (FL) (FL) (FL) u163 FUNCTION KEY ASSY (AWU8062) : The power supply is shown with the marked box. P R S T XV-HTD330 http://www.xiaoyu163.com...
Symbol In Schematic Part Name Diagrams Diagrams C E B Capacitor Connector Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
CARRIAGE MOTOR MOTOR Contact Side Contact Side Contact Side Contact Side Contact Side Contact Side (ANP7473-A) (ANP7473-A) (VNP1884-B) (VNP1884-B) SPINDLE SPINDLE MOTOR CN122 CN61 MOTOR u163 A B C D A B C D A B C D XV-HTD330 http://www.xiaoyu163.com...
CN3001 CN3002 CN3021 CN3022 UPSIDE W136 CAUTION W137 GNDA REPLACE WITH SAME TYPE W154 NO.491007 FOR IC25 W155 MFD.BY LITTELFUSE INC. W156 AMP TRADE ASSY W153 AWU8059 W152 CMK-P3X CN3011 CN3012 u163 (ANP7456-A) CN3031 CN3032 K L M XV-HTD330 http://www.xiaoyu163.com...
Page 61
L 13942296513 CN5613 CN5612 (ANP7456-A) AMP TRADE ASSY CN3022 CN3021 CN3021 CN3022 UPSIDE GNDA ATTENTION CMK-P3X EN CAS DE REMPLACEMENT DES FUSIBLES IC25 N'UTILISER QUE LA REFERENCE 491007 DE CHEZ LITTELFUSE INC. CN3012 CN3011 CN3012 CN3011 (ANP7456-A) u163 XV-HTD330 http://www.xiaoyu163.com...
STAND BY L 13942296513 W120 W119 CMK-P3X CONTACT SIDE CN52 SECONDARY IC51 CN51 (ANP7456-A) VIDEO JACK ASSY VIDEO ASSY W118 AWU8061 W117 W114 W113 CN5103 W112 JA8802 JA8851 CMK-P3X CONTACT SIDE UP CN8003 CONTACT SIDE UP u163 (ANP7456-A) XV-HTD330 http://www.xiaoyu163.com...
Page 63
AC IN PRIMARY AWU8057 AWU8066 AWU8067 CMK-P3X L 13942296513 SECONDARY SYSPOW GNDD VE+56 IC51 WCLK WEN/DI (ANP7456-A) VIDEO JACK ASSY VIDEO ASSY CMK-P3X CN8001 AWU8061 VD+5 GNDV GNDV GNDV GNDV Cr/R GNDV Cb/B GNDV CY/G CN8003 CN8003 u163 (ANP7456-A) XV-HTD330 http://www.xiaoyu163.com...
REGULATOR IC (1.8V) PQ018EZ01ZP OTHERS > IC421 REGULATOR IC PQ018EH01ZP CN11 8P CONNECTOR VKN1268 > IC431 REGULATOR IC (5.0V) MM1565AF CN12 7P CONNECTOR VKN1267 > IC441 REGULATOR IC PQ20WZ11 IC501 DVD VIDEO AMP IC MM1623AF IC601 BACK END IC STM5589CVA XV-HTD330 http://www.xiaoyu163.com...
Electrical adjustments are not required. L 13942296513 6.3 JIGS AND MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1067) Screw tight (GYL1001) DVD test disc Precise screwdriver Soldering iron (GGV1025) u163 XV-HTD330 http://www.xiaoyu163.com...
Purpose: To set the sweep which was correct with the individual Traverse mechanism. Be sure to perform the following step finally when replaced Pickup, Traverse Mechanism and Spindle Motor. CLEAR GGF1067 Test mode remote control unit (It is necessary when performed adjustment procedure Ÿ.) u163 XV-HTD330 http://www.xiaoyu163.com...
< When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY CHP/TIM Press keys in order 030000 TEST MODE: OFF POWER u163 GGF1067 Test mode remote control unit XV-HTD330 http://www.xiaoyu163.com...
Mechanism Base and turn each screw to adjust Turn the Short switch to Short side when L 13942296513 the height. (Refer to "6.1 ADJUSTMENT ITEMS AND removing the Pickup Flexible Cable. LOCATION".) (Refer to "7.1.13 DISASSEBLY".) Turn a flat side into bottom u163 XV-HTD330 http://www.xiaoyu163.com...
Page 86
If error rate is OK, Disc playback normally. locks a root of • The measurement of block error rate tangential and radial adjustment screws with the Screw tight, and go to step Screw tight: GYL1001 Test mode end u163 XV-HTD330 http://www.xiaoyu163.com...
Page 87
3 7 63 1515 0 Purpose: To set the sweep which was correct with the individual Traverse mechanism. Turn on the Player POWER CLEAR Note: Be sure to perform this step when replaced the Pickup or Traverse mechanism. L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
Perform only trace, video and audio outputs are nothing. = Screen display ON/OFF 1. Turn off the display by pressing the [AUDIO] (A8-1E) key of the remote control unit. 2. Turn on the display by pressing the [DISPLAY] (A8-43) key of the remote control unit. u163 XV-HTD330 http://www.xiaoyu163.com...
Page 89
• After the search, perform only trace and video and audio outputs are nothing. 4. Release the Search address input • Clear the address by pressing the [CLEAR] (A8-45) key. Release the address input mode when pressing the [CLEAR] key once again. L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
Kinds of version / firmware of the FE. Scart terminal output [SK – ∗ ∗] RAM or ROM (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] u163 S-VIDEO : [01] : [02] XV-HTD330 http://www.xiaoyu163.com...
After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. XV-HTD330 http://www.xiaoyu163.com...
(version of ST core software) softwareVersion . softwareRevision / buildNumber 0 F.E VERSION Version of FRONT END (version of mechanism controller CHIP software) MainVersion / Kinds of firmware RAM or ROM - Remote control code = Key code of Main unit u163 XV-HTD330 http://www.xiaoyu163.com...
PLL lost timeout 0x93 u163 DECODER ERROR 0xa∗ DECODER TIMEOUT 0xb∗ Note : 0 x & & ID lost error 0xa3 ID lost timeout 0xb3 DEVICE ERROR 0xd∗ code SRAM error 0xd1 (Only this part is displayed to a display) XV-HTD330 http://www.xiaoyu163.com...
Page 95
S E R V I C E LINE2 S E R V I C E u163 TUNER S E R V I C E S E R V I C E LINE1 S E R V I C E XV-HTD330 http://www.xiaoyu163.com...
Page 96
1. Stepping motor of the stepping in the test mode? 2. Inside switch Stepping move timeout 0 x 54 Did timeout at stepping movement Do indicate "S-04" at the most inner 3. Driver periphery of the stepping? u163 XV-HTD330 http://www.xiaoyu163.com...
Page 97
0 x d1 Cannot access SRAM 2. Front End IC Is not bus line short-circuiting? 3. Front End-SRAM bus line FAILSAFE (0 x e∗) 1. software runaway Unexpected error 0 x e1 Unexpected error 3. Software bug u163 XV-HTD330 http://www.xiaoyu163.com...
(The SEARCH key is not accepted after all 9 digits have been entered.) Input ID Number ! [Player's ID Number Setting] ID Number ? > 0 0 0 0 0 0 0 0 1 OK ? <PLAY> Compare Mode <SEARCH> Enter Input ID Number ! u163 XV-HTD330 http://www.xiaoyu163.com...
Page 99
[Player's ID Number Setting] ID Number ? [ 0 0 0 0 0 0 0 0 1 ] Compare > 0 0 0 0 0 0 0 0 1 OK? <PLAY> Enter <STOP> Memory Clear Input ID Number ! u163 XV-HTD330 http://www.xiaoyu163.com...
Page 100
If no ID data are set after the ID number is changed, the message "NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. u163 XV-HTD330 http://www.xiaoyu163.com...
Pins 18 and 19 of the KEY input terminal is 5 All operation keys re disabled. has already been pressed. V. If it is not, check if the operation switch on the line is in failure. L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
BACK END IC (DVDM IC601) Assy ? (Is a signal fluctuating of 0-3.3V ?) • Is the motor drive voltage output it at CN124 pin 7 and pin 8 ? IC151 and peripheral parts of the DVDM Assy u163 XV-HTD330 http://www.xiaoyu163.com...
Page 103
"NO ID DATA" flashes on the screen and FL display for a few (Picture is normal) Is signal output from DOUT signal (CN911-pin 21) on the DVDM Assy ? DVDM CN911-pin 21 seconds after the power is turned on or during Stop mode. u163 XV-HTD330 http://www.xiaoyu163.com...
Page 104
When the rotary tray rotates, a rattling sound is heard. • Breaking or damage of the disc detect Even during playback, the indication "NO DISC" is displayed. sensor (PC21) It takes longer than normal until playback starts. u163 XV-HTD330 http://www.xiaoyu163.com...
Page 105
Disc Detect Sensor Flexible Cable (7P) : VDA1835 (PC21 : GP2S28) (TRSB CN12 ↔ SSRB CN21) Rotary Tray : VNK4923 Open Open Close Close Motor : DXM1143 Tray Open/Close (for Rotary Tray Drive) Position Detect SW u163 (S21 : VSK1011) XV-HTD330 http://www.xiaoyu163.com...
Replace IC8702. Is connector for pin 17 ? Insert it tightly. inserted tightly Pin 5 Do perform 3V→5V conversion Replace IC8702. for pin 15 ? Pin 7 Do perform 3V→5V conversion Replace IC8702. for pin 13 ? u163 XV-HTD330 http://www.xiaoyu163.com...
Page 107
Do perform Step 4 5V→3V conversion Replace IC8701. for pin 4 ? IC8701 Pin 18 Pin 3 Do perform Do perform 5V→3V conversion Replace IC8701. 5V→3V conversion Replace IC8701. for pin 2 ? for pin 17 ? u163 XV-HTD330 http://www.xiaoyu163.com...
Page 108
"NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. BCK (pin 26) Replace IC8201. outputting it? IC8502-pin2 20MHz clock Replace IC8502 or X8501. outputting it? u163 XV-HTD330 http://www.xiaoyu163.com...
Page 109
Replace IC8401. IC8701 Pin 18 Pin 3 Pin 28 Do perform Does Do perform 5V→3V conversion Replace IC8701. a signal output Replace IC8401. 5V→3V conversion Replace IC8701. for pin 2 ? for pin 17 ? u163 XV-HTD330 http://www.xiaoyu163.com...
• If no pulse is input to the AC terminal (Pin 4) for about 60 msec when the microcomputer is in Memory Backup mode, it will not do any processing. • The unit will recover from Memory Backup mode if a reset command is input to the XRESET terminal (Pin 8). u163 XV-HTD330 http://www.xiaoyu163.com...
7.1.11 WAVEFORM POINTS LOCATION 3 7 63 1515 0 SIDE A SIDE A DVDM ASSY CN122 CN121 TRAY POS CLAMP SEDR+ SEDR- DISCSENS OPEN IC101 CN124 CN123 RFOUT IC301 SPDL_PDM L 13942296513 ROT_DRV IC601 u163 Front Side XV-HTD330 http://www.xiaoyu163.com...
1.83 ohms or less, Q3601 begins to operate, Q3639 is turned on, Q3640 (E, C, and B)is turned on, and the level of XPROTECT becomes MID. → The microcomputer detects the XPROTECT level and u163 shuts the power to the unit off. Front Side XV-HTD330 http://www.xiaoyu163.com...
Page 114
D3658, Q3651 (E, C, B) is turned off, Q3651 (E2, B2, C2) is low. ← The microcomputer detects the XPROTECT level and shuts turned on, and the level of XPROTECT becomes low. the power to the unit off. XV-HTD330 http://www.xiaoyu163.com...
Page 115
Point (A) becomes high enough to turn Q131 on, and the level of the XPROTECT line becomes low. The microcomputer detects the XPROTECT level and shuts the power to the unit off. u163 XV-HTD330 http://www.xiaoyu163.com...
Page 116
Point (A) becomes high enough to turn Q131 on, and the level of the XPROTECT line becomes low. The microcomputer detects the XPROTECT level and shuts the power to the unit off. u163 XV-HTD330 http://www.xiaoyu163.com...
Page 117
Q3632 (E2, C2, B2), Q3633, and Q3636 (E, C, B) are turned on, the line to activate the SP relay becomes low level, and the SP Relay is turned off. (2) HP MUTE Q3635 is turned on, and the MUTE circuit for HP is turned on. u163 XV-HTD330 http://www.xiaoyu163.com...
When reattaching the bonnet, to avoid damaging the unit, hook the bonnet by supporting and lightly pushing it upward by hand from the rear, as shown in the photo below. Gear Pulley Bonnet Gear Pulley u163 Hook Bottom View XV-HTD330 http://www.xiaoyu163.com...
Page 119
3 7 63 1515 0 Remove the bonnet and tray cap. (See Step ¥.) Remove the three screws. Remove the one screw. Remove the four hooks. GND Plate L HTM ×3 L 13942296513 Remove the Front Panel Section. Front Panel Section u163 XV-HTD330 http://www.xiaoyu163.com...
Page 120
Note : After replacement, connect the flexible cable, then remove the soldered joint (open). L 13942296513 Rear Panel Reattatch the clamper holder by tighten the two screws. DVDM Assy Rear View Table Mechanism Section Table Mechanism Section DISPLAY Assy u163 XV-HTD330 http://www.xiaoyu163.com...
Page 121
To DVDM To DVDM Jig cable CN911 CN923 (GGD1160) DVDM Assy L 13942296513 Insert the insulation sheet between the DVDM Assy and the chassis. Arrange the cables as shown in the photo below. Insulation sheet u163 DVDM Assy XV-HTD330 http://www.xiaoyu163.com...
Page 122
The screw(5) of AMP Module can be removed even if it does not remove VIDEO JASK Assy. Connect the two jig cables. Arrange the cables as shown in the photo below. ×2 Jig cable (GGD1315) AMP TRADE Assy CN3031 CN3032 CN3011 CN3012 u163 6CH AMP Assy XV-HTD330 http://www.xiaoyu163.com...
Page 123
Arrange the cables as shown in the photo below. Connect the AF Assy with the AMP Module Section using a jig cable. AF Assy Jig cable Table Mechanism Section (GGD1315) AF Assy DVDM Assy PRIMARY Assy AMP Module Section u163 XV-HTD330 http://www.xiaoyu163.com...
Page 124
(open). Remove the four screws. L 13942296513 Disconnect the three flexible cables and the one connector. Remove the Table Mechanism Section. Rear View DVDM Assy Rear Panel Table Mechanism Section Table Mechanism Section u163 XV-HTD330 http://www.xiaoyu163.com...
Page 125
It is not necessary to set the Disc No. of the rotary tray, because the Automatic Disc No. Detection system will function. Adjust the position of the rotary tray so that the center hole can be seen. u163 XV-HTD330 http://www.xiaoyu163.com...
Page 126
Barrier A HTM Mecha Frame HTM L 13942296513 Arrangement of the flexible cables when reassembling Barrier A HTM 8P Flexible cable 17P Flexible cable 24P Flexible cable 2P Wire cable DVDM Assy To DVDM Assy Mecha Frame HTM u163 XV-HTD330 http://www.xiaoyu163.com...
Page 127
L 13942296513 Remove the five screws. 24P Flexible cable Remove the Traverse Mecha. Assy-S. ×2 Traverse Mecha. Assy-S ×4 Float Rubber Note on the Float Rubber Installation Pole of the Float Base ×2 Float Rubber u163 ×2 Hook XV-HTD330 http://www.xiaoyu163.com...
Page 128
L 13942296513 Mount the Table Mechanism Section on the Mechanism Base Section. Connect the flexible cable. Bring an extra flexible cable close to the front side. Mechanism Base Section Flexible cable Side View Side View u163 Table Mechanism Section XV-HTD330 http://www.xiaoyu163.com...
Page 129
If the boss is set in this position, the unit does not operate correctly. If the boss is set in the cam groove, the unit operates correctly. Table Mechanism Section L 13942296513 Table Mechanism Section Cam groove Mechanism Base Section u163 Planet Base Boss part XV-HTD330 http://www.xiaoyu163.com...
Page 130
Notes on Assembling the Mechanism Section 3 7 63 1515 0 Clamper Plate Tray Gear Motor (for Tray) Motor Pulley (for Tray Motor) Motor Holder Worm Gear, Tray Belt L 13942296513 Motor (for Loading) Motor Pulley (for Loading Motor) u163 XV-HTD330 http://www.xiaoyu163.com...
Page 131
Apply lubricating oil (GYA1001) to the holder part. Motor Holder Apply lubricating oil (GYA1001). Clamper Plate Motor (for Loading), Motor Pulley (for Loading Motor) Adjust the height of the motor pulley to 6.2mm. Motor Pulley 6.2mm u163 Motor Apply lubricating oil (GYA1001). XV-HTD330 http://www.xiaoyu163.com...
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC STM6316ATXXA, STM5589C, PDC103A 7 STM6316ATXXA (DVDM ASSY : IC301) • FRONT END IC ¶ Block Diagram L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
Page 133
3 7 63 1515 0 ¶ Pin Function t i c t i c t s i L 13942296513 t s i t s i t s i t s i t i s t i s u163 XV-HTD330 http://www.xiaoyu163.com...
Page 134
- t l l i c y t i - t l l i c y t i - t l l i c y t i d l l u163 XV-HTD330 http://www.xiaoyu163.com...
Page 135
3 7 63 1515 0 l l i l l i t i c l i b y t i L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
Page 136
7 STM5589CVA (DVDM ASSY : IC601) 3 7 63 1515 0 • BACK END IC ¶ Pin Function . r i & l a i L 13942296513 l a i . t i . t i u163 XV-HTD330 http://www.xiaoyu163.com...
Page 137
3 7 63 1515 0 . r i t i s t i s t i s t i s t i s t i s t i s t i s t s i t s i L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
Page 138
: ' L XV-HTD330 http://www.xiaoyu163.com...
Page 139
3 7 63 1515 0 . r i r i f ' L ' ' L ' ' L ' t i r ' L ' ' L ' L 13942296513 ' L ' ' L ' u163 XV-HTD330 http://www.xiaoyu163.com...
Page 140
3 7 63 1515 0 . r i L 13942296513 ' L ' l a i l a i u163 XV-HTD330 http://www.xiaoyu163.com...
Page 141
3 7 63 1515 0 . r i L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
Page 142
Chip select 1 for system bus XHPMUTE HP MUTE ON/OFF XRECMUTE REC OUTPUT MUTE ON/OFF XMUTEC Cch MUTE ON/OFF REAR RELAY ON/OFF RYFSC FRONT/SW/CENTER RELAY ON/OFF TIMERLED Control TIMER LED LEVELSHIFT VOL 0 to 5 : H VSS4 VSS4 VDD4 VDD4 u163 XV-HTD330 http://www.xiaoyu163.com...
Page 143
WIRE LESS OUTPUT SELECT A INPUTSELB AUDIO INPUT SELECT B INPUTSELA AUDIO INPUT SELECT A XTL0 Selection X'tal to DIR DIRERR LOCK/UNLOCK from DIR DIRRST Reset to DIR /CODEC DIRCS Chip select to DIR/CODEC PB7/D7 DIRDO Data input from DIR/CODEC u163 XV-HTD330 http://www.xiaoyu163.com...
Page 144
• PortE and PortF can be selected for input or output by each 2 bits. • In case of without RDS, it is best that RDSDATA and RDSCLK are assigned as I/O port which can be set output and output low level. u163 XV-HTD330 http://www.xiaoyu163.com...
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Position to be cleaned Cleaning tools Fans Cleaning paper : GED-008 L 13942296513 u163 XV-HTD330 http://www.xiaoyu163.com...
Press to start playback of any disc in the player. Lights when the timer is set. u163 This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording(VR) mode. 20 PHONES jack Headphone jack. XV-HTD330 http://www.xiaoyu163.com...
Page 148
(kHz for AM, MHz for FM) Lights when Rec Mode is on. 19 Character display 11 Timer indicators Lights when the timer is set u163 Lights during multi-angle scenes on a DVD disc Lights when the sleep timer is active XV-HTD330 http://www.xiaoyu163.com...
Page 149
Press to change the camera angle during • Use with SHIFT for QUIET/MIDNIGHT: Use to select DVD multi-angle scene playback. the Quiet and Midnight modes. ZOOM u163 14 RETURN Press to change the screen zoom level. Press to return to a previous menu screen. XV-HTD330 http://www.xiaoyu163.com...
Page 150
CD Mode on/off. REPEAT (SHIFT + 2 18 SHIFT Use to select a repeat play mode. Use to access the functions/commands printed in green on the remote (press the button for the function you want while holding down SHIFT). u163 XV-HTD330 http://www.xiaoyu163.com...