hit counter script
Cisco Nexus 5596 Hardware Installation Manual
Cisco Nexus 5596 Hardware Installation Manual

Cisco Nexus 5596 Hardware Installation Manual

Replacing an i/o module nexus 5000 series

Advertisement

Replacing Components

This chapter describes how to remove and install components for the Cisco Nexus 5500 Platform switch
or the Cisco Nexus 5000 Platform switch.
This section includes the following sections:
To prevent ESD damage, wear grounding wrist straps during these procedures and handle modules by
Caution
the carrier edges only.
Replacing an I/O Module for a Cisco Nexus 5548 Switch
To replace an I/O module with another I/O module (Layer 2 I/O module or layer 3 I/O module) you must
remove the right fan module and then pull the I/O module out using the handle of the left fan module,
which is installed in the middle of the I/O module. You then install the replacement I/O module and fill
its fan module slots with the fan modules from the original I/O module.
If the module includes the product ID on the front, it is a Layer 3 I/O module (product ID N55-D160L3
Note
or N55-D160L3-V2). The N55-D160L3-V2 uses a newer version of the Layer 3 ASIC and enables higher
table sizes in a future software release from 8K host entries to 16K host entries or from 4K multicast
routes to 8K multicast routes (IPv4). The Layer 2 module (product ID N55-DL2) does not include the
product ID on the front.
Replacing an I/O Module for a Cisco Nexus 5548 Switch, page 4-1
Replacing Expansion Modules, page 4-5
Replacing or Installing Power Supplies, page 4-8
Replacing a Fan Module, page 4-13
Removing the Cisco Nexus 5500 Platform Chassis or the Cisco Nexus 5000 Platform Chassis,
page 4-17
C H A P T E R
Cisco Nexus 5000 Series Hardware Installation Guide
4
4-1

Advertisement

Table of Contents
loading

Summary of Contents for Cisco Nexus 5596

  • Page 1: Replacing Components

    C H A P T E R Replacing Components This chapter describes how to remove and install components for the Cisco Nexus 5500 Platform switch or the Cisco Nexus 5000 Platform switch. This section includes the following sections: Replacing an I/O Module for a Cisco Nexus 5548 Switch, page 4-1 •...
  • Page 2: Removing An I/O Module

    • Installing an I/O Module, page 4-4 Removing an I/O Module To remove an I/O module from a Cisco Nexus 5548 chassis, follow these steps: Prepare an antistatic surface for placing removed components. Step 1 On the right fan module, loosen its captive screw so that it is no longer connected to the chassis or I/O...
  • Page 3 Chapter 4 Replacing Components Replacing an I/O Module for a Cisco Nexus 5548 Switch Figure 4-2 Removing a Fan Tray from the I/O Module in the Chassis Loosen the captive screw on the right most fan Pull the fan tray out of the I/O module and tray so that the screw is free of the I/O module.
  • Page 4: Installing An I/O Module

    4-14. Installing an I/O Module To install an I/O module in a Cisco Nexus 5548 chassis, follow these steps: Align the replacement I/O module to the I/O module slot in the chassis and push the module all the way Step 1 into the slot so that its two captive screws are aligned to their holes in the chassis.
  • Page 5: Replacing Expansion Modules

    “Installing the Switch” section on page 2-5. Cisco NX-OS Release 5.0(2)N1(1) does not support the hot swapping of a Cisco Nexus 5548 expansion Note module during switch operations. Instead, you must power down the switch before removing and replacing an expansion module.
  • Page 6: Installing An Expansion Module In A Cisco Nexus 5500 Platform Chassis

    Installing an Expansion Module in a Cisco Nexus 5500 Platform Chassis To install an expansion module in a Cisco Nexus 5500 Platform switch chassis, follow these steps: For the Layer 3 GEMs (N55-M160L3 and N55-M160L3-V2) in the Cisco Nexus 5596UP switch, you Step 1 must power down the switch first.
  • Page 7: Installing An Expansion Module In The Cisco Nexus 5000 Platform Chassis

    4-7. Installing an Expansion Module in the Cisco Nexus 5000 Platform Chassis To install an expansion module in the Cisco Nexus 5000 Platform chassis, follow these steps: Step 1 Grasp the handle of the module and place your other hand under the module to support it.
  • Page 8: Replacing Or Installing Power Supplies

    If you are installing a new power supply where one did not exist before, follow the installation procedure. You can use port-side exhaust airflow power supply modules for all Cisco Nexus 5000 and 5500 switches and you can alternatively use port-side intake airflow power supply modules with the Cisco Nexus 5548UP switch.
  • Page 9: Removing A Power Supply

    Removing a Power Supply If you are using a Cisco Nexus 5500 Platform switch or a Cisco Nexus 5000 Platform switch with one Caution power supply, removing the power supply causes the switch to shut down. If you are using two power supplies and you remove one of them, the switch can continue to operate.
  • Page 10 Chapter 4 Replacing Components Replacing or Installing Power Supplies Figure 4-9 Removing the Power Supply from a Cisco Nexus 5548 Switch Figure 4-10 Removing the Power Supply from a Cisco Nexus 5020 Switch Cisco Nexus 5000 Series Hardware Installation Guide...
  • Page 11: Installing A Power Supply

    Installing a Power Supply, page 4-11 Installing a Power Supply To install a power supply in a Cisco Nexus 5500 Platform chassis or the Cisco Nexus 5000 Platform chassis, follow these steps: Ensure that the system (earth) ground connection has been made. For ground connection instructions,...
  • Page 12: Wiring A Dc Power Connector

    Finger tight or about 3 ft./lbs should be sufficient. Step 4 Insert the red (DC positive) wire into the left aperture on the connector and tighten down the connection set screw. Do not tighten over 0.7 Nm. Cisco Nexus 5000 Series Hardware Installation Guide 4-12...
  • Page 13: Replacing A Fan Module

    You can use port-side exhaust fan modules with all Cisco Nexus 5000 switches and you can alternatively use port-side intake fan modules with only the 5548UP switches.
  • Page 14: Removing A Fan Module

    To install a fan module, follow these steps: Hold the fan module with the LED at the bottom (Cisco Nexus 5596 or Cisco Nexus 5020) or right (Cisco Step 1 Nexus 5548 or Cisco Nexus 5010).
  • Page 15 Step 2 into the chassis as far as it can go until the captive screw makes contact with the chassis, and tighten the captive screw. To install a fan module in a Cisco Nexus 5596 chassis, see Figure 4-13. To install a fan...
  • Page 16 Replacing Components Replacing a Fan Module Figure 4-15 Installing a Fan Module in a Cisco Nexus 5020 Chassis Figure 4-16 Installing a Fan Module in a Cisco Nexus 5010 Chassis If the switch is powered on, listen for the fans. You should immediately hear them operating. If you do...
  • Page 17 To remove the Cisco Nexus 5500 Platform chassis or the Cisco Nexus 5000 Platform chassis from a rack, follow these steps:...
  • Page 18 Chapter 4 Replacing Components Repacking Cisco Nexus 5500 Platform Switch Components or Cisco Nexus 5000 Platform Switch Components for Cisco Nexus 5000 Series Hardware Installation Guide 4-18...

This manual is also suitable for:

Nexus 5020Nexus 5548Nexus 5010

Table of Contents