Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
Refer to
instruction
manual
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool.
WARNING! Familiarise yourself with the specific applications and limitations of the tool as well as any potential hazards.
This tool should be used in conjunction with inspection maintenance procedures recommended in the vehicle manufacturer's manual.
Ensure that the tool is correct for the task.
Wear the appropriate personal protective equipment for the task. A full range is available from your Sealey dealer.
DO NOT use the tool for any purpose other than that for which it is designed.
Ensure there is adequate lighting prior to using the tool.
Keep children and unauthorised persons away from the working area.
DO NOT use the tool if any parts are damaged or missing, as this may cause failure and/or personal injury.
DO NOT use the tool when you are tired, or under the influence of alcohol, drugs or intoxicating medication.
After use, store in a safe, dry childproof area.
2. INTRODUCTION
Professional design ideal for the workshop technician or competent DIY enthusiast. Enables the accurate balancing after tyre fitting and truing
of warped or buckled spoke wheels. Includes two cones and spindle for precise, easy alignment and balancing. Uses gravity to find the heavy
point of a wheel and tyre. Also has threaded centring stabilizer bolts to securely hold the wheel whilst truing the rim. Truing is done by adjusting
the tension of the spokes.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WTS01
Maximum Cone Size Balancer: . . . . . . . . . . . Ø37.5mm
Centre Balncer Spindle to Base: . . . . . . . . . . . . 585mm
Maximum Cone Size Truing Axle:. . . . . . . . . . . .Ø37mm
Centre Truing Axle to Base: . . . . . . . . . . . . . . . . 445mm
4.1.
Assembling the Stand. See fig.1.
4.1.1. Screw the two uprights to the base, with the bearings facing
inwards, using 8 x hex headed screws and nuts.
4.1.2. Screw the threaded bolts through the uprights and screw a
cone onto each one.
4.1.3. Screw the four feet into the base and use a spirit level to
ensure the stand is level.
4.1.4. Place the cones on to the spindle and place the spindle onto
the bearings.
4.1.5. Slide the truing pointer into its holder and tighten the holding
screw. The pointer can be adjusted up and down by undoing
the nut on the back.
© Jack Sealey Limited
INSTRUCTIONS FOR
MOTORCYCLE & BICYCLE WHEEL
BALANCER & TRUING STAND
WTS01
MODEL No:
Original Language Version
fig.1
WTS01 Issue: 1 - 25/02/15
Advertisement
Related Manuals for Sealey WTS01
Summary of Contents for Sealey WTS01
- Page 1 3. SPECIFICATION Model No: ......WTS01 Maximum Cone Size Balancer: ... Ø37.5mm Centre Balncer Spindle to Base: .
- Page 2 WARNING! Sealey can not accept responsibility for incorrect use of this product. The end user should seek appropriate advice before use. 3.3. Wheel Truing See fig.3 3.3.1 Use the threaded centring bolts to securely hold the wheel whilst truing the rim.
- Page 3 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.