free stats
Cisco Catalyst 6500 Series Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. 6500 - Catalyst Series 10 Gigabit EN Interface Module...
  6. Installation manual
Cisco Catalyst 6500 Series Installation Manual

Cisco Catalyst 6500 Series Installation Manual

Switch module
Hide thumbs Also See for Catalyst 6500 Series:
Table of Contents

Advertisement

Quick Links

See also: Troubleshooting Manual , Reference Manual
Catalyst 6500 Series Switch Module
Installation Guide
October 2003
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 526-4100
Customer Order Number: DOC-7815725=
Text Part Number: 78-15725-02

Advertisement

Table of Contents
loading

Related Manuals for Cisco Catalyst 6500 Series

Summary of Contents for Cisco Catalyst 6500 Series

  • Page 1 Catalyst 6500 Series Switch Module Installation Guide October 2003 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: DOC-7815725= Text Part Number: 78-15725-02...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
  • Page 3 CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet,...

  • Page 5: Table Of Contents

    Obtaining Additional Publications and Information xxiii Product Overview C H A P T E R Catalyst 6000 Series Switches Catalyst 6500 Series Switches Supervisor Engines LEDs 1-12 RESET Button 1-13 CONSOLE Port 1-13 Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 6 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6348-RJ21V) 1-28 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6348-RJ-45) 1-29 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6348-RJ45V) 1-30 24-Port 100BASE-FX Fabric-Enabled Ethernet Switching Module (WS-X6524-100FX-MM) 1-31 48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6548-GE-TX) 1-31 Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 7 Ethernet Module LEDs 1-47 ATM Modules 1-48 1-Port OC-12 ATM Module (WS-X6101-OC12-MMF) 1-49 1-Port OC-12 ATM Module (WS-X6101-OC12-SMF) 1-50 ATM Module LEDs 1-51 FlexWAN Module (WS-X6182-2PA) 1-52 Multilayer Switch Module (WS-X6302-MSM) 1-54 Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 8 1-87 Power Management and Environmental Monitoring 1-88 Preparing for Installation C H A P T E R Limiting Connection Distances Determining Cable Distances Ethernet and Fast Ethernet Gigabit Ethernet 10-Gigabit Ethernet Catalyst 6500 Series Switch Module Installation Guide viii 78-15725-02...
  • Page 9 Using Flash PC Cards 3-17 Installing and Removing a Flash PC Card 3-19 Verifying the Installation 3-19 Verifying Newly Installed Modules 3-20 Checking Connectivity 3-22 What To Do After Installing Modules and Verifying Connectivity 3-22 Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 10 Console Port Mode 1 Signaling and Pinouts B-10 Console Port Mode 2 Signaling and Pinouts B-13 Fiber-Optic Connectors B-14 SC Connectors B-14 MT-RJ Connectors B-15 LC Connectors B-16 Cleaning the Fiber-Optic Connectors B-17 N D E X Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 11: Preface

    Preface This preface describes who should read the Catalyst 6500 Series Switch Module Installation Guide, how it is organized, and its document conventions. Audience Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, replace, or service the equipment described in this publication.

  • Page 12: Organization

    This publication is organized as follows: Chapter Title Description Chapter 1 Product Overview Provides an overview of the Catalyst 6500 series switches, the supervisor engine, Ethernet switching modules, and ATM modules. Chapter 2 Preparing for Installation Describes how to prepare your site before installing the...
  • Page 13 Cautions use the following conventions: Means reader be careful. In this situation, you might do something that could Caution result in equipment damage or loss of data. Catalyst 6500 Series Switch Module Installation Guide xiii 78-15725-02...

  • Page 14: Statement 1071-Warning Definition

    Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 15 Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 16 Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 17 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Catalyst 6500 Series Switch Module Installation Guide xvii 78-15725-02...
  • Page 18 Preface Conventions Catalyst 6500 Series Switch Module Installation Guide xviii 78-15725-02...

  • Page 19: Related Documentation

    Preface Related Documentation Related Documentation For instructions on installing and configuring Catalyst 6500 series switches, refer to these publications: Regulatory Compliance and Safety Information for the Catalyst 6500 Series • Switches Site Preparation and Safety Guide • • Catalyst 6500 Series Switch Quick Software Configuration Guide Catalyst 6500 Series Switch Installation Guide •...

  • Page 20: Cisco.com

    Preface Obtaining Documentation Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.com International Cisco websites can be accessed from this URL: http://www.cisco.com/public/countries_languages.shtml...

  • Page 21: Documentation Feedback

    Cisco Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services, online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.

  • Page 22: Cisco Tac Website

    The Cisco TAC website (http://www.cisco.com/tac) provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365 days a year. Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password.

  • Page 23: Tac Case Priority Definitions

    Obtaining Additional Publications and Information TAC Case Priority Definitions To ensure that all cases are reported in a standard format, Cisco has established case priority definitions. Priority 1 (P1)—Your network is “down” or there is a critical impact to your business operations.
  • Page 24 You can access Packet magazine at this URL: http://www.cisco.com/packet iQ Magazine is the Cisco bimonthly publication that delivers the latest • information about Internet business strategies for executives. You can access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine...

  • Page 25: Product Overview

    C H A P T E R Product Overview This chapter describes the Catalyst 6000 series switches, the Catalyst 6500 series switches, supervisor engines, and switching modules. This chapter contains these sections: Catalyst 6000 Series Switches, page 1-2 • Catalyst 6500 Series Switches, page 1-4 •...

  • Page 26: Catalyst 6000 Series Switches

    Throughout this publication, except where noted, the term supervisor engine is Note used to refer to Supervisor Engine 1, Supervisor Engine 2, and Supervisor Engine 720. Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 27 The Switch Fabric Modules are not supported in the Note Catalyst 6000 series switches. Hot-swappable fan assembly and modules • Redundant AC-input or DC-input power supplies • Backplane bandwidth of 32 Gbps • Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 28: Catalyst 6500 Series Switches

    Chapter 1 Product Overview Catalyst 6500 Series Switches Catalyst 6500 Series Switches The Catalyst 6500 series switches consist of the following six chassis: • Catalyst 6503 (3 slots) Catalyst 6506 (6 slots) • Catalyst 6509 (9 slots) • Catalyst 6509-NEB (9 slots, vertical) •...
  • Page 29 Switch Fabric Module can be installed in slot 6. Only the WS-X6500-SFM2 Switch Fabric Module can be installed in – slot 7 of the Catalyst 6513 switch. A redundant WS-X6500-SFM2 Switch Fabric Module can be installed in slot 8. Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 30: Supervisor Engines

    Catalyst 6500 Series Switches Key Features Feature Description Performance and Refer to the Catalyst 6500 Series Switch Software Configuration Guide or the Configuration Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide for detailed information about the features supported on the switches.
  • Page 31 Chapter 1 Product Overview Catalyst 6500 Series Switches Table 1-1 Catalyst 6500 Series Switches Key Features (continued) Feature Description Component Modules (including the supervisor engine if you have redundant supervisor Hot-Swapping engines) and fans can be replaced without interrupting the system power or causing other software or interfaces to shut down.

  • Page 32: Reset Button

    Supervisor Engine 1A, dual 1000BASE-X GBIC • uplinks QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t • WS-X6K-S1A-MSFC2 Supervisor Engine 1A, dual 1000BASE-X GBIC • uplinks, PFC and MSFC2 daughter cards QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t • Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 33 MSFC2, 256 MB on supervisor engine, 256 MB on MSFC2 • QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t WS-X6K-S2-PFC2 Supervisor Engine 2, dual 1000BASE-X GBIC • uplinks, fabric-enabled, and supports a PFC2 QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t • Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 34 Supervisor Engine 1, Figure 1-2 shows the front panel features of Supervisor Engine 2, and Figure 1-3 shows the front panel features of the Supervisor Engine 720. Catalyst 6500 Series Switch Module Installation Guide 1-10 78-15725-02...
  • Page 35 Reset button Figure 1-3 Supervisor Engine 720 Front Panel Features CompactFlash LINK LEDs Type II slots Status LEDs Gigabit Ethernet Disk LEDs uplink port Console port 10/100/1000 uplink port Catalyst 6500 Series Switch Module Installation Guide 1-11 78-15725-02...
  • Page 36 The supervisor engine is operational and active. Orange The supervisor engine is in standby mode. PWR MGMT Green Sufficient power is available for all modules. Orange Sufficient power is not available for all modules. Catalyst 6500 Series Switch Module Installation Guide 1-12 78-15725-02...
  • Page 37 The CONSOLE port allows you to access the switch either locally (with a console terminal) or remotely (with a modem). The CONSOLE port is an EIA/TIA-232 asynchronous, serial connection with hardware flow control and an RJ-45 connector. Catalyst 6500 Series Switch Module Installation Guide 1-13 78-15725-02...

  • Page 38: Console Port Mode Switch

    The cable and adapters shipped with the switch are the same ones used on the Note Cisco 2500 series routers (and other Cisco products). Additionally, you can connect a modem to the console port using the cable and adapter provided with the switch.

  • Page 39: Switch Load

    In a redundant configuration with two supervisor engines, the uplink ports on the Note redundant (standby) supervisor engine are active and can be used for normal traffic like any other ports in the chassis. Catalyst 6500 Series Switch Module Installation Guide 1-15 78-15725-02...

  • Page 40: 10/100 And 10/100/1000 Ethernet Switching Modules

    SFP 1-Gbps port connector or a 10/100/1000BASE-T RJ-45 connector. 10/100 and 10/100/1000 Ethernet Switching Modules In this chapter, the term Catalyst 6500 series modules refers to modules that can Note be installed in either the Catalyst 6000 series switch chassis (Catalyst 6006 and...
  • Page 41 (WS-X6548-RJ-21), page 1-33 • 48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-45), page 1-34 48-Port 10/100/1000BASE-T Fabric-Enabled Ethernet Switching Module • (WS-X6748-GE-TX), page 1-35 Table 1-4 lists the features of the Ethernet switching modules. Catalyst 6500 Series Switch Module Installation Guide 1-17 78-15725-02...
  • Page 42 32 Gbps Bus Centralized 128 KB 2 transmit, 1 receive WS-X6348-RJ-45 32 Gbps Bus Centralized Optional 128 KB 2 transmit, 1 receive WS-X6348-RJ45V 32 Gbps Bus Centralized 128 KB 2 transmit, 1 receive Catalyst 6500 Series Switch Module Installation Guide 1-18 78-15725-02...
  • Page 43 Bus 2 receive Supports optional DFC card WS-X6748-GE-TX Switch Fabric CEF720 1.3 MB 4 transmit, 2 receive 1. Supports IP phones. 2. Supports an optional inline power field upgrade module (WS-F6K-VPWR=) Catalyst 6500 Series Switch Module Installation Guide 1-19 78-15725-02...

  • Page 44: 24-Port 10Base-Fl Ethernet Switching Module (Ws-X6024-10Fl-Mt)

    The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. This module is a Class 1 laser product. Refer to the Regulatory Compliance and Note Safety Information for the Catalyst 6500 Series Switches for information on working with lasers. Figure 1-4...

  • Page 45: 48-Port 10/100/1000Base-T Ethernet Switching Module (Ws-X6148-Ge-Tx)

    Ethernet signals. The power signals are completely transparent to the Ethernet signals and do not interfere with their operation. Catalyst 6500 Series Switch Module Installation Guide 1-21 78-15725-02...

  • Page 46: 48-Port 10/100Base-T Ethernet Switching Module (Ws-X6148-Rj21V)

    Ethernet signals and do not interfere with their operation. Phone discovery—Automatically detects the presence of an IP phone and • supplies inline power to the phone. Catalyst 6500 Series Switch Module Installation Guide 1-22 78-15725-02...

  • Page 47: 48-Port 10/100Base-T Ethernet Switching Module (Ws-X6148-Rj45V)

    Auxiliary VLANs—Provides automatic VLAN configuration for IP phones • using IEEE 802.1Q as the standards-based VLAN tagging mechanism between the switch and the IP phone. Catalyst 6500 Series Switch Module Installation Guide 1-23 78-15725-02...

  • Page 48: 24-Port 100Base-Fx Ethernet Switching Module (Ws-X6224-100Fx-Mt)

    MT-RJ optical connectors for connection to MMF optical cable. This module is a Class 1 laser product. Refer to the Regulatory Compliance and Note Safety Information for the Catalyst 6500 Series Switches for information on working with lasers. The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t.

  • Page 49: 48-Port 10/100Base-T Ethernet Switching Module (Ws-X6248-Rj45)

    The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 1-11 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6248-TEL) WS-X6248-RJ-TEL 48 PORT ETHERNET SWITCHING 10/100 BASE-T MODULE The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-25 78-15725-02...

  • Page 50: 48-Port 10/100Base-T Ethernet Switching Module (Ws-X6248A-Tel)

    24 MT-RJ connectors for connection to the MMF cable. This module is a Class 1 laser product. Refer to the Regulatory Compliance and Note Safety Information for the Catalyst 6500 Series Switches for information on working with lasers. The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t.

  • Page 51: 24-Port 100Base-Fx Ethernet Switching Module (Ws-X6324-100Fx-Sm)

    24 MT-RJ connectors for connection to SMF cable. This module is a Class 1 laser product. Refer to the Regulatory Compliance and Note Safety Information for the Catalyst 6500 Series Switches for information on working with lasers. The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t.

  • Page 52: 48-Port 10/100Base-T Ethernet Switching Module (Ws-X6348-Rj21V)

    The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 1-15 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6348-RJ-21V) WS-X6348-RJ21 STATUS 48 PORT 10/100 BASE-T SWITCHING MODULE PHONE ETHERNET The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-28 78-15725-02...

  • Page 53: 48-Port 10/100Base-T Ethernet Switching Module (Ws-X6348-Rj-45)

    The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 1-16 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6348-RJ-45) WS-X6348-RJ-45 STATUS PHONE 48 PORT ETHERNET SWITCHING 10/100 BASE-T MODULE The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-29 78-15725-02...

  • Page 54: 48-Port 10/100Base-T Ethernet Switching Module (Ws-X6348-Rj45V)

    The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 1-17 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6348-RJ45V) WS-X6348-RJ-45V STATUS 48 PORT ETHERNET SWITCHING PHONE 10/100 BASE-T MODULE The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-30 78-15725-02...

  • Page 55: 24-Port 100Base-Fx Fabric-Enabled Ethernet Switching Module (Ws-X6524-100Fx-Mm)

    Distributed Forwarding Card (WS-F6K-DFC). This module is a Class 1 laser product. Refer to the Regulatory Compliance and Note Safety Information for the Catalyst 6500 Series Switches for information on working with lasers. The QoS port architecture (Rx/Tx) for this module is 1p1q0t/1p3q1t.

  • Page 56: 48-Port 10/100/1000Base-T Ethernet Switching Module (Ws-X6548V-Ge-Tx)

    Auxiliary VLANs—Provides automatic VLAN configuration for IP phones • using IEEE 802.1Q as the standards-based VLAN tagging mechanism between the switch and the IP phone. The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Catalyst 6500 Series Switch Module Installation Guide 1-32 78-15725-02...

  • Page 57: 48-Port 10/100Base-T Fabric-Enabled Ethernet Switching Module

    The QoS port architecture (Rx/Tx) for this module is 1p1q0t/1p3q1t. Figure 1-21 48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-21) WS-X6548-RJ21 STATUS 48 PORT 10/100 BASE-T SWITCHING MODULE ETHERNET The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-33 78-15725-02...

  • Page 58: 48-Port 10/100Base-T Fabric-Enabled Ethernet Switching Module (Ws-X6548-Rj-45)

    The QoS port architecture (Rx/Tx) for this module is 1p1q0t/1p3q1t. Figure 1-22 48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-45) WS-X6548 STATUS 48 PORT 10/100 BASE-T SWITCHING MODULE ETHERNET The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-34 78-15725-02...

  • Page 59: 48-Port 10/100/1000Base-T Fabric-Enabled Ethernet Switching Module (Ws-X6748-Ge-Tx)

    The QoS port architecture (Rx/Tx) for this module is 1q8t/1p3q8t. Figure 1-23 48-Port 10/100/1000BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6748-GE-TX) WS-X6748-GE-TX 48 PORT 10/100/1000 RJ-45 STATUS SWITCHING MODULE The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-35 78-15725-02...

  • Page 60: Gigabit Ethernet Switching Modules

    Table 1-5 Gigabit and 10-Gigabit Ethernet Switching Modules Features Number of Number of Backplane Transmit Receive Product Number Connection Forwarding Queues/Port Queues/Port WS-X6316-GE-TX Centralized WS-X6408-GBIC Centralized WS-X6408A-GBIC Centralized WS-X6416-GBIC Centralized WS-X6416-GE-MT Centralized Catalyst 6500 Series Switch Module Installation Guide 1-36 78-15725-02...
  • Page 61 2. The module can be installed in slots 2–6 in the Catalyst 6506, slots 2–9 in the Catalyst 6509 and Catalyst 6509-NEB, and slots 9–13 in the Catalyst 6513 switches. It cannot be installed in slots 2–8 of the Catalyst 6513 switch. The module requires a Supervisor Engine 720. Catalyst 6500 Series Switch Module Installation Guide 1-37 78-15725-02...

  • Page 62: 16-Port Gigabit Ethernet Switching Module (Ws-X6316-Ge-Tx)

    Gigabit Ethernet Switching Modules These modules are Class 1 laser products. Refer to the Regulatory Compliance Note and Safety Information for the Catalyst 6500 Series Switches for information on working with lasers. 16-Port Gigabit Ethernet Switching Module (WS-X6316-GE-TX) The 16-port Gigabit Ethernet switching module (WS-X6316-GE-TX) provides 16 switched, full-duplex Gigabit Ethernet ports.

  • Page 63: 8-Port Gigabit Ethernet Switching Module (Ws-X6408A-Gbic)

    The QoS port architecture (Rx/Tx) for this module is 1p1q4t/1p2q2t. Figure 1-26 8-Port Gigabit Ethernet Switching Module (WS-X6408A-GBIC) WS-X6408 8 PORT GIGABIT ETHERNET 1000BASE-X GBIC ports The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-39 78-15725-02...

  • Page 64: 16-Port Gigabit Ethernet Switching Module (Ws-X6416-Gbic)

    The QoS port architecture (Rx/Tx) for this module is 1p1q4t/1p2q2t. Figure 1-27 16-Port Gigabit Ethernet Switching Module (WS-X6416-GBIC) WS-X6416-GBIC 16 PORT GIGABIT ETHERNET The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-40 78-15725-02...

  • Page 65: 16-Port Gigabit Ethernet Switching Module (Ws-X6416-Ge-Mt)

    Distributed Forwarding Card (WS-F6K-DFC). Figure 1-29 1-Port 10-Gigabit Ethernet Module (WS-X6501-10GEX4) WS-X6501-10GEX4 Metro 10GigE 10G BASE-EX4 The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-41 78-15725-02...

  • Page 66: 1-Port 10-Gigabit Ethernet Base Module (Ws-X6502-10Ge)

    CWDM GBICs are used with the CWDM Passive Optical System. For more Note information on the CWDM Passive Optical System, refer to the Installation Note for the CWDM Passive Optical System. Catalyst 6500 Series Switch Module Installation Guide 1-42 78-15725-02...

  • Page 67: 16-Port Gigabit Ethernet Switching Module (Ws-X6516A-Gbic)

    (Rx/Tx) for this module is 1p1q4t/1p2q2t. The module has 1 MB per port buffers. The WS-X6516A-GBIC module has a single fabric channel interface. The switching module is upgradable to support distributed forwarding by installing an optional Distributed Forwarding Card (WS-F6K-DFC). Catalyst 6500 Series Switch Module Installation Guide 1-43 78-15725-02...

  • Page 68: 16-Port 10/100/1000Base-T Gigabit Ethernet Switching Module (Ws-X6516-Ge-Tx)

    10GBASE-LR long-reach or 10GBASE-ER extended reach XenPak optical transceivers. The WS-X6704-10GE module has dual fabric channel interface and requires the Supervisor Engine 720. The QoS port architecture (Rx/Tx) for this module is 1q8t/1p7q8t. Catalyst 6500 Series Switch Module Installation Guide 1-44 78-15725-02...

  • Page 69: 24-Port Gigabit Ethernet Switching Module (Ws-X6724-Sfp)

    The QoS port architecture (Rx/Tx) for this module is 1q8t/1p3q8t. Figure 1-35 24-Port Gigabit Ethernet Switching Module (WS-X6724-SFP) WS-X6724-SFP 24 PORT GIGABIT ETHERNET-SFP STATUS The front panel LEDs are described in Table 1-6 on page 1-47. Catalyst 6500 Series Switch Module Installation Guide 1-45 78-15725-02...

  • Page 70: 16-Port Gigabit Ethernet Switching Module (Ws-X6816-Gbic)

    The WS-X6816-GBIC must have a DFC3A daughter card installed to Note operate with the Supervisor Engine 720. A Switch Fabric Module must be installed in the Catalyst 6500 series switch • chassis when a WS-X6816-GBIC module is installed. The WS-X6816-GBIC can be installed in slots 1 through 6 in the •...

  • Page 71: Ethernet Module Leds

    If the module fails to download code and configuration information successfully during the initial reset, the LED stays red; the module does not come online. The module is not receiving power. Catalyst 6500 Series Switch Module Installation Guide 1-47 78-15725-02...

  • Page 72: Atm Modules

    ATM Module LEDs, page 1-51 • These modules are Class 1 laser products. Refer to the Regulatory Compliance Note and Safety Information for the Catalyst 6500 Series Switches for information on working with lasers. Catalyst 6500 Series Switch Module Installation Guide 1-48...

  • Page 73: 1-Port Oc-12 Atm Module (Ws-X6101-Oc12-Mmf)

    Figure 1-37 ATM OC-12 Module (MMF) (WS-X6101-OC12-MMF) WS-X6101-OC12-MMF CONSOLE PORT ACTIVE ACTIVE SIGNAL SIGNAL LINK CONSOLE PORT UNI-622MM UNI-622MM MULTIMODE OC-12 ATM MODE The front panel LEDs are described in Table 1-7 on page 1-51. Catalyst 6500 Series Switch Module Installation Guide 1-49 78-15725-02...

  • Page 74: 1-Port Oc-12 Atm Module (Ws-X6101-Oc12-Smf)

    Figure 1-38 ATM OC-12 Module (SMF) (WS-X6101-OC12-SMF) WS-X6101-OC12-SMF CONSOLE PORT ACTIVE ACTIVE SIGNAL SIGNAL LINK CONSOLE PORT UNI-622MM UNI-622MM SINGLE MODE OC-12 ATM MODE The front panel LEDs are described in Table 1-7 on page 1-51. Catalyst 6500 Series Switch Module Installation Guide 1-50 78-15725-02...

  • Page 75: Atm Module Leds

    The port is transmitting a packet (the LED is lit for approximately 50 milliseconds). RX (receive) Green The port is receiving a packet (the LED is lit for approximately 50 milliseconds). Catalyst 6500 Series Switch Module Installation Guide 1-51 78-15725-02...

  • Page 76: Flexwan Module (Ws-X6182-2Pa)

    FlexWAN module, provides multiprotocol routing support with full Internet route connectivity for speeds ranging from serial RS-232 to OC-3. The FlexWAN module can accept up to two Cisco 7200/7500 WAN port adapters, which deliver WAN consolidation and extend QoS and traffic-management capabilities over WAN segments.
  • Page 77 PA-MC-8E1/120 PA-MC-T3 PA-MC-E3 PA-MC-STM-1 For more information about the MSFC and PFC, refer to the Catalyst 6500 Series Switch Software Configuration Guide. Throughout this publication, except where noted, the term MSFC refers to both Note MSFC and MSFC2, and the term PFC refers to both PFC and PFC2.

  • Page 78: Multilayer Switch Module (Ws-X6302-Msm)

    Multilayer Switch Module (WS-X6302-MSM) The Multilayer Switch Module (MSM) (WS-X6302-MSM) provides multiprotocol routing for the switch Ethernet interfaces. Cisco IOS features available for the MSM are listed in Table 1-10. Catalyst 6500 Series Switch Module Installation Guide...
  • Page 79 Chapter 1 Product Overview Multilayer Switch Module (WS-X6302-MSM) Table 1-10 Cisco IOS Features for the Multilayer Switch Module Feature Description Layer 3 forwarding Wire speed IP, IP multicast, and IPX routing • between VLANs Support for up to 64K entries for IP network •...
  • Page 80 Chapter 1 Product Overview Multilayer Switch Module (WS-X6302-MSM) Table 1-10 Cisco IOS Features for the Multilayer Switch Module (continued) Feature Description Layer 3-related protocols IGMP v1 and v2 • IGMP snooping • Cisco Group Multicast Protocol (CGMP) server • support Full ICMP support •...
  • Page 81 Use a paper clip or a small, pointed object to access the CONSOLE PORT MODE Note switch. Catalyst 6500 Series Switch Module Installation Guide 1-57 78-15725-02...

  • Page 82: Network Analysis Modules

    Network Analysis Modules The Network Analysis Modules (NAMs) monitor and analyze network traffic for the Catalyst 6000 series and Catalyst 6500 series switches using Remote Monitoring (RMON), RMON2, and other MIBs. The RMON support that the NAM provides for Ethernet VLANs is an extension of the RMON support provided by the supervisor engine.

  • Page 83: Network Analysis Module (Ws-Svc-Nam-1)

    The NAM collects network traffic statistics for real-time traffic analysis, performance monitoring, and troubleshooting. The NAM monitors and analyzes network traffic for the Catalyst 6500 series switches using remote monitoring (RMON), RMON extensions for switched networks (SMON), and other management information bases (MIBs).
  • Page 84 SHUTDOWN button as an alternative shutdown method. For information on NAM module hardware and software requirements and port adapter installation and configuration, refer to the Catalyst 6500 Series Network Analysis Module Installation and Configuration Note. Catalyst 6500 Series Switch Module Installation Guide...

  • Page 85: Network Analysis Module (Ws-Svc-Nam-2)

    The NAM monitors and analyzes network traffic for the Catalyst 6500 series switches using remote monitoring (RMON), RMON extensions for switched networks (SMON), and other management information bases (MIBs). The NAM supports the following RMON groups: •...
  • Page 86 SHUTDOWN button as an alternative shutdown method. For information on NAM module hardware and software requirements and port adapter installation and configuration, refer to the Catalyst 6500 Series Network Analysis Module Installation and Configuration Note. Catalyst 6500 Series Switch Module Installation Guide...

  • Page 87: Firewall Services Module (Ws-Svc-Fwm-1-K9)

    Depending on the response from the server, which matches a request against a list of 17 website characteristics that are considered inappropriate for business use, the module either permits or denies the connection. Catalyst 6500 Series Switch Module Installation Guide 1-63 78-15725-02...
  • Page 88 Network Address Translation (NAT) and Port Address Translation • (PAT)—Cisco firewalls provide NAT and PAT services that conceal IP addresses of internal networks and expand network address space for internal networks. Denial-of-service (DoS) attack prevention—Cisco firewalls protect the •...
  • Page 89 CLI or NAM shutdown commands, you can use the SHUTDOWN button as an alternative shutdown method. For further information on the Firewall Services Module, refer to the Catalyst 6500 Series Firewall Services Module Installation and Configuration Note. Catalyst 6500 Series Switch Module Installation Guide...

  • Page 90: Ipsec Vpn Acceleration Services Module (Ws-Svc-Ipsec-1)

    IPSec VPN Acceleration Services Module (WS-SVC-IPSEC-1) IPSec VPN Acceleration Services Module (WS-SVC-IPSEC-1) The IPSec VPN Acceleration Services module is a Gigabit Ethernet IPSec cryptographic module that you can install in the Catalyst 6500 series switches. (See Figure 1-44.) The VPN module provides bump-in-the-wire (BITW) IPSec implementation using VLANs.
  • Page 91 Product Overview IPSec VPN Acceleration Services Module (WS-SVC-IPSEC-1) When you configure a VPN on the Cisco routers, a packet is sent to a routed interface that is associated with an IP address. If the interface has an attached crypto map, the software checks that the packet is on an access control list (ACL) specified by the crypto map.

  • Page 92: Intrusion Detection System Module (Ws-X6381-Ids)

    IPSec VPN Acceleration Services Module Installation and Configuration Note. Intrusion Detection System Module (WS-X6381-IDS) The Intrusion Detection System Module (IDSM) is part of the Cisco Secure Intrusion Detection System (Cisco Secure IDS) and is managed by the Cisco Secure Policy Manager (Cisco Secure PM). (See Figure 1-45.) Cisco Secure PM...
  • Page 93 When the Intrusion Detection System Module detects an attack, it generates an alarm. Alarms are generated by the Intrusion Detection System Module through the Catalyst 6500 series switch backplane to the Cisco Secure PM, where they are logged or displayed on a graphical user interface. Alarm communication is...
  • Page 94 Module. To prevent corruption of the module, it is critical that you shut down the module properly. To properly shut down the switching module, session into the Intrusion Detection System Module from the Catalyst 6500 series switch console and enter the shutdown command. If the Intrusion Detection System Module fails to respond to the shutdown command, press the SHUTDOWN button to manually shut down the Intrusion Detection System Module.

  • Page 95: Content Switching Module (Ws-X6066-Slb-Apc)

    Figure 1-46 Content Switching Module (WS-X6066-SLB-APC) Status RJ-45 (Test) connector The STATUS LED displays the Content Switching Module status as described in Table 1-17. Catalyst 6500 Series Switch Module Installation Guide 1-71 78-15725-02...

  • Page 96: Switch Fabric Modules

    For redundancy, you can install a second Switch Fabric Module. The first-installed Switch Fabric Module functions as the primary module. When you install two modules at the same time, the module in slot 5 functions as the primary Catalyst 6500 Series Switch Module Installation Guide 1-72 78-15725-02...

  • Page 97: Switch Fabric Module 2 (Ws-X6500-Sfm2)

    Supervisor Engine 2 and must be installed in slot 5 or slot 6 of the Catalyst 6506, Catalyst 6509, or Catalyst 6509-NEB switches, or in slot 7 or slot 8 of the Catalyst 6513 switch. Catalyst 6500 Series Switch Module Installation Guide 1-73 78-15725-02...
  • Page 98 Two push button switches control the LCD display: SELECT—This switch is used for LCD display menu selection. • NEXT—This switch is used to scroll to the next item on the LCD display • menu. Catalyst 6500 Series Switch Module Installation Guide 1-74 78-15725-02...

  • Page 99: Voice-Related Modules

    Communications Media Module (WS-SVC-CMM) The Catalyst 6500 series Communications Media Module can support single or multiple Cisco CallManagers in a voice-over-IP network. (See Figure 1-49.) The...
  • Page 100 Communications Media Module Gigabit Ethernet backplane interface through the CLI using the interface GigabitEthernet1/0 command. For an overview of a VoIP network using the Catalyst 6500 series switches, refer Note to the “Configuring a VoIP Network” section of the Catalyst 6500 Series Switch Software Configuration Guide at this URL: http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_7_4/confg_gd...
  • Page 101 E&M = ear and mouth DTMF = Dual Tone Multi-Frequency DTMF is supported; DTMF/MF is not supported For additional information, refer to the Catalyst 6500 Series and Cisco 7600 Series Communication Media Module Installation and Verification Note. The front panel LEDs are described in Table 1-19.
  • Page 102 The module is operational; the supervisor engine has • granted module online status. 1. Enter the show environment temperature mod command to display the temperature of each of four sensors on the module. Catalyst 6500 Series Switch Module Installation Guide 1-78 78-15725-02...
  • Page 103 Table 1-20 6-Port T1 and E1 Interface Modules Receive Port LEDs Color/State Description Green T1/E1 interface is operational. T1/E1 receive alarm. Yellow T1/E1 remote alarm. The administrative port shut down or there is no power. Catalyst 6500 Series Switch Module Installation Guide 1-79 78-15725-02...

  • Page 104: 8-Port T1/E1 Pstn Interface Module (Ws-X6608-T1/E1)

    (See Figure 1-52.) The module requires an IP address, is registered with Cisco CallManager in its domain, and is managed by Cisco CallManager. The module software is downloaded from a TFTP server. Depending upon which software you download, the ports can serve as T1/E1 interfaces or support...
  • Page 105 The module is not receiving power. The module was powered down due to lack of power. (The module is listed as power-deny in the show module status field.) Catalyst 6500 Series Switch Module Installation Guide 1-81 78-15725-02...

  • Page 106: 24-Port Fxs Analog Interface Module (Ws-X6624-Fxs)

    European Union standards. Connecting the port to this type of public network can cause severe personal injury or can damage the unit. Statement 1031 Catalyst 6500 Series Switch Module Installation Guide 1-82 78-15725-02...
  • Page 107 Note must have a system ground cable attached to the chassis. Refer to the Catalyst 6000 Series Switch Installation Guide or the Catalyst 6500 Series Switch Installation Guide for the system grounding cable installation procedure. Figure 1-53 24-Port FXS Analog Interface Module (WS-X6624-FXS)

  • Page 108: Port Addresses

    For more information, see the “Physical Interface Addresses” section on page 1-85. For Catalyst 6500 series switches running Cisco IOS software, refer to the Note Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide for port address information.

  • Page 109: Physical Interface Addresses

    8 PORT GIGABIT ETHERNET Port numbers 6/1 to 6/24 Port numbers 7/1 to 7/24 Port numbers 8/1 to 8/24 Port numbers 9/1 to 9/24 INPUT OUTPU T FAIL INPUT OUTPU T FAIL Catalyst 6500 Series Switch Module Installation Guide 1-85 78-15725-02...

  • Page 110: Mac Addresses

    MAC address. This addressing scheme gives the switch the intelligence to identify the state (connected or not connected) of each interface. When you hot swap a module, the MAC address changes with the module. Catalyst 6500 Series Switch Module Installation Guide 1-86 78-15725-02...

  • Page 111: Hot Swapping Supervisor Engines And Switching Modules

    To avoid erroneous failure messages, note the current configuration of all Caution interfaces before you remove or replace another switching module, and allow at least 15 seconds for the system to reinitialize after a module has been removed or replaced. Catalyst 6500 Series Switch Module Installation Guide 1-87 78-15725-02...

  • Page 112: Power Management And Environmental Monitoring

    Power Management and Environmental Monitoring For detailed information on power management and environmental monitoring, refer to the Catalyst 6500 Series Switch Software Configuration Guide or Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide. Catalyst 6500 Series Switch Module Installation Guide...

  • Page 113: Chapter 2 Preparing For Installation

    This chapter does not contain instructions for installing the switch chassis. For information on installing the switch chassis, refer to the Catalyst 6000 Series Switch Installation Guide or the Catalyst 6500 Series Switch Installation Guide. Limiting Connection Distances The length of your networks and the distances between connections depend on the type of signal, the signal speed, and the transmission media (the type of cabling used to transmit the signals).

  • Page 114: Determining Cable Distances

    10-Gigabit Ethernet, page 2-7 • Patch Cord, page 2-9 • Differential Mode Delay, page 2-11 • Console Port Cabling Specifications—Supervisor Engine Only, page 2-13 • Port Connector Requirements—Switching Modules Only, page 2-14 • Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 115: Atm

    ATM OC-12 Optical Specifications for SMF Cables Characteristic Specification Optical source Laser Wavelength 1300 nm Transmitter output power –15 to –8 dBm Receiver sensitivity –28 to –8 dBm Maximum cabling distance 9.3 mi (15 km) Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 116: Ethernet And Fast Ethernet

    Table 2-5 lists the optical characteristics for 100BASE-FX. Table 2-4 10BASE-FL Optical Characteristics Characteristic Specification Optical source Wavelength 850 nm Transmitter output power –20 to –12 dBm Receiver sensitivity –32.5 to –12 dBm Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 117: Gigabit Ethernet

    Gigabit Interface Converter (GBIC) channel insertion losses. All optical GBIC interfaces have SC connectors, and the minimum cable distance for the optical GBICs listed (MMF and SMF) is 6.5 feet (2 meters). Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 118 6. The minimum link distance for ZX GBICs is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance is 24.9 miles (40 km). Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 119: 10-Gigabit Ethernet

    12.4 miles (20 km). To prevent severe damage to the WS-X6501-10GEX4 receiver, you must install a 5-dB 1550 nm fixed-loss attenuator when fiber-optic cable lengths are less then 6.2 miles (10 km). Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 120 7. According to the IEEE 802.ae standard. Requires a 5 dB 1550 nm fixed-loss attenuator for distances less than 20 km. The exact distances supported by this module vary according to the number of splices and connectors in the fiber-optic cable attached to the OIM. Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 121: Patch Cord

    Patch Cord When using the long wavelength/long haul (LX/LH) GBIC with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord (Cisco product number CAB-GELX-625 or equivalent) between the GBIC and the MMF cable on both the transmit and receive ends of the link. The patch cord is required for link distances greater than 984 feet (300 meters).
  • Page 122 Chapter 2 Preparing for Installation Determining Cable Distances Cisco Gigabit Ethernet products have been tested and evaluated to comply with Note the standards listed in Appendix A, “Technical Specifications.” Equivalent cables should also meet these standards. Patch Cord Configuration Example Figure 2-1 shows a typical configuration using the patch cord.

  • Page 123: Differential Mode Delay

    Gigabit Ethernet experiences this problem because of its very high baud rate and its long MMF cable lengths. SMF cable and copper cable are not affected by DMD. Catalyst 6500 Series Switch Module Installation Guide 2-11 78-15725-02...
  • Page 124 A significant variation in the amount of DMD is produced from one MMF cable to the next. No reasonable test can be performed to survey an installed cable plant to assess the effect of DMD. Therefore, you must use the mode-conditioning Catalyst 6500 Series Switch Module Installation Guide 2-12 78-15725-02...

  • Page 125: Console Port Cabling Specifications-Supervisor Engine Only

    These cables and adapters are the same as those shipped with the Cisco 2500 series routers and other Cisco products. The supervisor engine front-panel console port mode switch allows you to...

  • Page 126: Port Connector Requirements-Switching Modules Only

    GBIC and the MMF cable. See the “Patch Cord” section on page 2-9 for details. RJ-45 male connectors for the 48-port 10/100BASE-T RJ-45 module. (See • Figure 2-5.) Catalyst 6500 Series Switch Module Installation Guide 2-14 78-15725-02...
  • Page 127 RJ-21 telco connectors for the 48-port 10/100BASE-T R J-21 telco module. • (See Figure 2-8.) Figure 2-4 SC Fiber-Optic Cable Connector Figure 2-5 RJ-45 Interface Cable Connector RJ-45 (both ends) Pin 1 Pin 8 Figure 2-6 MT-RJ Fiber-Optic Cable Connector Catalyst 6500 Series Switch Module Installation Guide 2-15 78-15725-02...

  • Page 128: Port Densities

    RJ-21 Telco Interface Cable Connectors RJ-21 port RJ-21 connector RJ-21 connector RJ-21 connector Port Densities Table 2-11 lists the bandwidth and port densities of the Catalyst 6000 series and Catalyst 6500 series switches. Catalyst 6500 Series Switch Module Installation Guide 2-16 78-15725-02...
  • Page 129 Chapter 2 Preparing for Installation Port Densities Table 2-11 Catalyst 6000 Series and Catalyst 6500 Series Bandwidth and Port Density Architecture Catalyst 6000 Series Switch Catalyst 6500 Series Switch Backplane Bandwidth 32 Gbps 32 to 256 Gbps Number of Gigabit...

  • Page 130: Gigabit Interface Converters

    Chapter 2 Preparing for Installation Gigabit Interface Converters Table 2-11 Catalyst 6000 Series and Catalyst 6500 Series Bandwidth and Port Density (continued) Architecture Catalyst 6000 Series Switch Catalyst 6500 Series Switch Number of ATM OC-12 5 (6 slots) Catalyst 6006 switch...

  • Page 131: Ws-G5483 Copper Gbic

    2-9.) Refer to your release notes or the online 1000BASE-T GBIC Switch Compatibility Matrix posted with the GBIC documentation on Cisco.com for the list of modules and the required software release level necessary to support this GBIC. To comply with GR-1089 intrabuilding, lightening-immunity requirements, you Caution must use foil-twisted pair (FTP) cable that is properly grounded at both ends.

  • Page 132: Ws-G5484, Ws-G5486, And Ws-G5487 Optical Gbics

    Each of the three types of optical GBICs comes in two physical models shown in Figure 2-10. These two physical models require different installation procedures. Figure 2-10 Optical GBIC Physical Styles (WS-G5484, WS-G5486, and WS-G5487) Clip Handle Receiver Transmitter Receiver Transmitter Catalyst 6500 Series Switch Module Installation Guide 2-20 78-15725-02...

  • Page 133: Coarse Wave Division Multiplexing Gbics

    Table 2-13 lists the available GBICs. These eight GBICs are installed in the Catalyst 6500 series modules that support GBICs and are used with the CWDM Passive Optical System. For more information on the CWDM Passive Optical System, refer to the Installation Note for the Cisco CWDM Passive Optical System.

  • Page 134: Sfp Optical Transceiver Modules

    Gigabit Ethernet module. The SFP optical transceiver modules use an LC connector. You can use any combination of SFP modules that your Cisco device supports. The only restrictions are that each SFP port must match the wavelength specifications on the other end of the cable and that the cable must not exceed the stipulated cable length for reliable communications.

  • Page 135: 1000Base-T Sfp Modules

    328 feet (100 meters) and have standard RJ-45 connectors. Figure 2-13 shows a 1000BASE-T SFP module. Figure 2-13 1000BASE-T SFP Transceiver Module Catalyst 6500 Series Switch Module Installation Guide 2-23 78-15725-02...

  • Page 136: Cwdm Sfp Optical Transceiver Modules

    Longwave 1570 nm laser, single mode Orange CWDM-SFP-1590 Longwave 1590 nm laser, single mode CWDM-SFP-1610 Longwave 1610 nm laser, single mode Brown Figure 2-14 shows a CWDM SFP with the optical port dust plug removed. Catalyst 6500 Series Switch Module Installation Guide 2-24 78-15725-02...

  • Page 137: Xenpak Optical Transceiver Modules

    The XenPak optical transceiver modules are hot-swappable, transceiver components that you can plug into standard receptacles in modules that convert Gigabit Ethernet electrical signals into a single-mode fiber-optic (SMF) interface. Figure 2-15 shows a XenPak optical transceiver module. Catalyst 6500 Series Switch Module Installation Guide 2-25 78-15725-02...

  • Page 138: Software Requirements

    Software Requirements For information on the minimum, recommended, and default software versions for the Catalyst 6000 series and Catalyst 6500 series switches, supervisor engines, and modules, refer to the applicable release notes for the latest maintenance release of your software.

  • Page 139: Installing The Module

    C H A P T E R Installing the Module This chapter describes how to install and verify the operation of the supervisor engine and switching modules in the Catalyst 6500 series switches, and it contains these sections: Required Tools, page 3-2 •...

  • Page 140: Required Tools

    Note least one supervisor engine. For information on installing the switch chassis, refer to the Catalyst 6000 Series Switch Installation Guide or the Catalyst 6500 Series Switch Installation Guide. This section describes how to install a supervisor engine in the chassis. Supervisor engines must be installed in specific slots in the chassis depending on which model of supervisor engine you are installing.
  • Page 141 • Slots 7 and 8 (13-slot chassis) • You should install switching-module filler plates (Cisco part number 800-00292-01) in any empty slots to maintain consistent airflow through the switch chassis. To prevent ESD damage, handle modules by the carrier edges only.
  • Page 142 To remove a module, refer to “Removing the Supervisor Engine or a Switching Module” section on page 3-12. Fully open both ejector levers on the new or replacement module. (See Step 5 Figure 3-1.) Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 143 MODE CONSOLE SUPERVISOR 2 PCMCIA EJECT WS-X6224 24 PORT 100FX EMI gasket INPUT OUTPU T FAIL INPUT OUTPU T FAIL WS-C 6500 -SFM SWIT CH FABR IC MDL Ejector lever fully extended Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 144 STATUS LED. If the STATUS LED changes from orange to green, the supervisor engine or module has successfully completed the boot process and is now online. If the STATUS LED remains orange or turns red, the Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 145 Press down WS-X62 24 24 PORT 100FX WS -C6 500 -SF 1 mm Gap between the module EMI gasket and the module above it SW ITC H FA BIR D MD L Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 146 45 degrees with respect to the module faceplate. (See Figure 3-5.) Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 147 Installing a Supervisor Engine or a Switching Module Figure 3-4 Positioning the Module in a Vertical Slot Chassis Ejector lever fully extended STATUS gasket gasket INPUT OUTPUT FAIL INPUT OUTPUT FAIL Insert module between slot guides Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 148 Clearing the EMI Gasket in a Vertical Slot Chassis Gap between the module EMI gasket and the module above it 1 mm STATUS Press left Press left INPUT OUTPUT FAIL INPUT OUTPUT FAIL Catalyst 6500 Series Switch Module Installation Guide 3-10 78-15725-02...
  • Page 149 For more information about the orange or red STATUS LED states, see the LED table for your specific module in Chapter 1. Catalyst 6500 Series Switch Module Installation Guide 3-11 78-15725-02...

  • Page 150: Removing The Supervisor Engine Or A Switching Module

    {host file | network | terminal} command. This step saves time when bringing the module back online. You can recover the configuration by downloading it from the server to the nonvolatile memory of the supervisor engine. Catalyst 6500 Series Switch Module Installation Guide 3-12 78-15725-02...
  • Page 151 Refer to the Catalyst 6500 Series Switch Software Configuration Guide or to the Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide for additional information.
  • Page 152 (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029 Catalyst 6500 Series Switch Module Installation Guide 3-14 78-15725-02...

  • Page 153: Connecting To The Console Port-Supervisor Engine Only

    CONSOLE PORT MODE switch in the in position (factory default). Connect to the port using the RJ-45-to-RJ-45 cable and RJ-45-to-DB-25 DTE adapter or RJ-45-to-DB-9 data terminal equipment (DTE) adapter (labeled “Terminal”). Catalyst 6500 Series Switch Module Installation Guide 3-15 78-15725-02...

  • Page 154: Connecting A Modem

    Invisible laser radiation may be emitted from disconnected fibers or Warning connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 Catalyst 6500 Series Switch Module Installation Guide 3-16 78-15725-02...

  • Page 155: Using Flash Pc Cards

    The plugs protect the GBIC and SFP optical bores and cable from contamination. For GBIC installation information, refer to the Gigabit Interface Converter Installation Note. For SFP installation information, refer to the Cisco Small Form-Factor Pluggable Module Installation Notes. Using Flash PC Cards...
  • Page 156 This section describes how to insert and remove a (PCMCIA) Flash PC card. For additional information related to the Flash PC card, refer to the Catalyst 6500 Series Switch Software Configuration Guide or the Catalyst 6500 Series Switch IOS Software Configuration Guide.

  • Page 157: Installing And Removing A Flash Pc Card

    This section describes how to verify the installation of a supervisor engine or switching module. To verify the installation of a Catalyst 6500 series switch running Cisco IOS software, refer to the Catalyst 6500 Series Switch IOS Software Configuration Guide.

  • Page 158: Verifying Newly Installed Modules

    --- -------------------------------------- ------ ---------- ----------------- 00-30-96-29-9f-84 to 00-30-96-29-9f-85 1.0 5.2(1) 6.1(0.128)ORL 00-30-96-29-9f-86 to 00-30-96-29-9f-87 00-50-3e-8d-64-00 to 00-50-3e-8d-67-ff 00-d0-bc-ed-6b-2c to 00-d0-bc-ed-6b-6b 1.2 12.0(7T)XE 12.0(7T)XE1(2.07) 00-90-2b-00-a7-ca to 00-90-2b-00-a7-cb 0.201 4B4LZ0XA 1.1(0.20) 00-50-f0-ac-30-54 to 00-50-f0-ac-30-83 1.0 4.2(0.24)V 6.1(0.128)ORL Catalyst 6500 Series Switch Module Installation Guide 3-20 78-15725-02...
  • Page 159 UnderSize ----- ---------- ---------- ---------- ---------- --------- Port Single-Col Multi-Coll Late-Coll Excess-Col Carri-Sen Runts Giants ----- ---------- ---------- ---------- ---------- --------- --------- --------- Last-Time-Cleared -------------------------- Fri March 2 2003, 20:41:52 Console> Catalyst 6500 Series Switch Module Installation Guide 3-21 78-15725-02...

  • Page 160: Checking Connectivity

    For complete information on configuring the supervisor engine and all modules, refer to the Catalyst 6500 Series Switch Software Configuration Guide or the Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide. For information on all Catalyst 6500...

  • Page 161: Appendix

    A P P E N D I X Technical Specifications In this appendix, the term Catalyst 6500 series modules refers to modules that can Note be installed in either the Catalyst 6000 series switch chassis (Catalyst 6006 and Catalyst 6009 switches) or the Catalyst 6500 series switch chassis (Catalyst 6503, Catalyst 6506, Catalyst 6509, Catalyst 6509-NEB, and Catalyst 6513 switches) unless specifically noted.

  • Page 162: Regulatory Standards Compliance

    Weight 3 to 10 lb (1.4 to 4.5 kg) Regulatory Standards Compliance Catalyst 6500 series switches comply with the regulatory standards listed in the Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches publication. Catalyst 6500 Series Switch Module Installation Guide...

  • Page 163: Appendix

    RJ-21 Connector, page B-2 • RJ-21 (WS-X6624-FXS Only), page B-4 • RJ-45 Connector, page B-5 • Supervisor Engine Console Port Signals and Pinouts, page B-8 • • Fiber-Optic Connectors, page B-14 Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 164: Connector

    Always ground the cables (especially in new cable runs) to a suitable and safe earth ground before connecting them to the module. Figure B-1 RJ-21 Connectors RJ-21 port RJ-21 connector RJ-21 connector RJ-21 connector Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 165 RxD (–) RxD (+) TxD (–) TxD (+) RxD (–) RxD (+) TxD (–) TxD (+) RxD (–) RxD (+) TxD (–) TxD (+) RxD (–) RxD (+) TxD (–) TxD (+) Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 166 RJ-21 Connector Pinouts (WS-X6224-FXS Analog Interface Module Only) Port Connector Pin Port Connector Pin Number Number Signal Number Number Signal Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 167: Rj-45 Connector

    Always ground the cables (especially in new cable runs) to a suitable and safe earth ground before connecting them to the module. To comply with GR-1089 intrabuilding, lightning-immunity requirements, you Caution must use foil-twisted pair (FTP) cable that is properly grounded at both ends. Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 168 3 (TD+) 1 (RD+) 6 (TD–) 2 (RD–) 4 (Not used) 4 (Not used) 5 (Not used) 5 (Not used) 7 (Not used) 7 (Not used) 8 (Not used) 8 (Not used) Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...
  • Page 169 1 (TP0+) 3 (TP1+) 2 (TP0–) 6 (TP1–) 3 (TP1+) 1 (TP0+) 6 (TP1–) 2 (TP1–) 4 (TP2+) 7 (TP3+) 5 (TP2–) 8 (TP3–) 7 (TP3+) 4 (TP2+) 8 (TP3–) 5 (TP2–) Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 170: Supervisor Engine Console Port Signals And Pinouts

    RJ-45-to-DB-25 female DTE adapter (labeled “Terminal”) • RJ-45-to-DB-25 male DCE adapter (labeled “Modem”) • This is the same cable and adapters that ship with the Cisco 2500 series routers and other Cisco products. Catalyst 6500 Series Switch Module Installation Guide 78-15725-02...

  • Page 171: Console Port Mode Switch

    B-5.) If your cable was purchased from Cisco Systems, pin 1 will be white on one connector, and pin 8 will be white on the other (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5).

  • Page 172: Console Port Mode 1 Signaling And Pinouts

    (labeled “Terminal”) to connect the console port to a PC running terminal emulation software. Table B-5 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-9 female DTE adapter. Catalyst 6500 Series Switch Module Installation Guide B-10 78-15725-02...
  • Page 173 RJ-45-to-DB-25 female DTE adapter. Table B-6 Port Mode 1: Console Port Signaling and Pinouts (DB-25 Adapter) RJ-45-to-DB-25 Terminal Console Console Port RJ-45-to-RJ-45 Rollover Cable Adapter Device Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal Catalyst 6500 Series Switch Module Installation Guide B-11 78-15725-02...
  • Page 174 (labeled “Modem”) to connect the console port to a modem. Table B-7 lists the pinouts for the asynchronous serial auxiliary port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 male DCE adapter. Catalyst 6500 Series Switch Module Installation Guide B-12 78-15725-02...

  • Page 175: Console Port Mode 2 Signaling And Pinouts

    (console port mode switch in the out position). See Table B-8 for the pinouts. Table B-8 Console Port Pinouts (Port Mode Switch Out) Console Port Console Device Pin (signal) Input/Output 1 (RTS) Output 2 (DTR) Output 3 (RxD) Input Catalyst 6500 Series Switch Module Installation Guide B-13 78-15725-02...

  • Page 176: Fiber-Optic Connectors

    Do not stare into beams or view directly with optical instruments. Statement 1051 The SC single-mode (fiber) connector is used to connect fiber-optic module ports with the external network. (See Figure B-6.) Figure B-6 SC Optical Connector Catalyst 6500 Series Switch Module Installation Guide B-14 78-15725-02...

  • Page 177: Mt-Rj Connectors

    Do not stare into beams or view directly with optical instruments. Statement 1051 The MT-RJ style connector is used on fiber-optic modules to increase port density. (See Figure B-7.) Figure B-7 MT-RJ Optical Connector Catalyst 6500 Series Switch Module Installation Guide B-15 78-15725-02...

  • Page 178: Lc Connectors

    Small Form-Factor Pluggable (SFP) tranceiver modules used on the Supervisor Engine 720 uplink ports use either MT-RJ connectors or LC connectors depending on the SFP vendor. Figure B-8 shows an LC connector. Catalyst 6500 Series Switch Module Installation Guide B-16 78-15725-02...

  • Page 179: Cleaning The Fiber-Optic Connectors

    Always install protective covers on unused or disconnected components to prevent contamination. Always clean fiber connectors before installing them. Catalyst 6500 Series Switch Module Installation Guide B-17 78-15725-02...
  • Page 180 If the surface is not clean or does not have an even shine, repeat the process using Note a fresh surface of the alcohol pad. Catalyst 6500 Series Switch Module Installation Guide B-18 78-15725-02...

  • Page 181: I N D E X

    1-48 to 1-52 10 Gigabit Ethernet optical specifications MMF (table) 5-dB attenuator requirement (caution) optical specifications SMF (table) optical characteristics (table) attenuators, using with 1000BASE-ZX GBIC optical transmission distance specifications (table) audience Catalyst 6500 Series Switch Module Installation Guide IN-1 78-15725-02...
  • Page 182 SMF 2-11 guidelines B-18 Catalyst 6006 switches commands description show module 3-20 Catalyst 6009 switches show port 1-86, 3-20 description write 3-12 Catalyst 6503 switches description Catalyst 6500 Series Switch Module Installation Guide IN-2 78-15725-02...
  • Page 183 2-14 See DMD connecting to 3-15 distance limitations description 1-13 port mode switch compared to laser transmission (figure) 2-12 signaling and pinouts connections mode 1 B-10 description mode 2 B-13 Catalyst 6500 Series Switch Module Installation Guide IN-3 78-15725-02...
  • Page 184 1-23 front panel (figure) 1-54 WS-X6148V-GE-TX 1-21 LEDs (table) 1-54 WS-X6248-RJ45 1-25 MSFC 1-52 WS-X6548-GE-TX 1-31 1-52 WS-X6548V-GE-TX 1-32 front panel features excessive link spans 2-13 console port 1-13 LEDs 1-12 Catalyst 6500 Series Switch Module Installation Guide IN-4 78-15725-02...
  • Page 185 See modes supervisor engines and modules 1-87 LINK LED ATM modules description (table) 1-52 description (table) 1-48 supervisor engine 1-13 IEEE, recommended signaling requirements Catalyst 6500 Series Switch Module Installation Guide IN-5 78-15725-02...
  • Page 186 1-84 modules See NAM blank module carriers NVRAM LED description 1-47 supervisor engine module 1-86 MSFCs FlexWAN modules 1-52 optical power specifications (table) supervisor engine features organization overfilled launch condition 2-12 Catalyst 6500 Series Switch Module Installation Guide IN-6 78-15725-02...
  • Page 187 WS-X6348-RJ-45V 1-30 RJ-45 connector, 10/100BASE-TX 2-14 PHONE LED description (table) 1-48 RJ-45 connectors physical interface addresses 1-85 description physical specifications (table) figure ping command 3-22 pinging a host 3-22 Catalyst 6500 Series Switch Module Installation Guide IN-7 78-15725-02...
  • Page 188 1-3, 1-4 firewall service modules 1-65 See also specific switches (for example, FlexWAN modules 1-54 Catalyst 6506 switches MSM module description (table) 1-57 Switch Fabric Module 2 use in Catalyst 6513 switches Catalyst 6500 Series Switch Module Installation Guide IN-8 78-15725-02...
  • Page 189 WS-G6483 OIM optical power specifications (table) uplink ports optical transmission specifications connecting to 3-16 (table) description 1-15 WS-G6488 OIM 1-42 optical power specifications (table) optical transmission specifications (table) verifying installation 3-20 Catalyst 6500 Series Switch Module Installation Guide IN-9 78-15725-02...
  • Page 190 WS-X6148-RJ21V 1-60 supported RMON groups 1-59 description 1-22 WS-SVC-NAM-2 front panel (figure) 1-23 description inline power 1-61 1-22 front panel (figure) LEDs 1-62 1-23 LEDs (table) 1-62 RMON groups supported 1-61 Catalyst 6500 Series Switch Module Installation Guide IN-10 78-15725-02...
  • Page 191 WAN adapters (table) 1-53 WS-X6224-100FX-MT description 1-24 front panel (figure) 1-24 LEDs 1-24 WS-X6248A-TEL description 1-26 front panel (figure) 1-26 LEDs 1-26 WS-X6248-RJ45 description 1-25 front panel (figure) 1-25 LEDs 1-25 Catalyst 6500 Series Switch Module Installation Guide IN-11 78-15725-02...
  • Page 192 (figure) 1-28 1-40 front panel (figure) LEDs 1-28 1-40 LEDs 1-28 WS-X6416-GE-MT WS-X6348-RJ-45 description 1-41 description front panel (figure) 1-29 1-41 front panel (figure) LEDs 1-29 1-41 LEDs 1-29 WS-X6348-RJ45V Catalyst 6500 Series Switch Module Installation Guide IN-12 78-15725-02...
  • Page 193 1-33 WS-X6516A-GBIC front panel (figure) 1-33 description 1-43 LEDs 1-33 Distributed Forwarding Card upgrade 1-43 WS-X6548-RJ-45 front panel (figure) 1-44 description 1-34 LEDs 1-44 front panel (figure) 1-34 LEDs 1-34 Catalyst 6500 Series Switch Module Installation Guide IN-13 78-15725-02...
  • Page 194 (figure) 1-45 LEDs 1-45 QoS architecture 1-44 WS-X6724-SFP description 1-45 front panel (figure) 1-45 LEDs 1-45 QoS architecture 1-45 WS-X6816-GBIC description 1-46 front panel (figure) 1-46 installation restrictions 1-46 LEDs 1-47 Catalyst 6500 Series Switch Module Installation Guide IN-14 78-15725-02...

Table of Contents