free stats
Download Print this page
Sealey POWER TOOLS SA789 Instructions
Sealey POWER TOOLS SA789 Instructions

Sealey POWER TOOLS SA789 Instructions

Air staple gun 25mm capacity

Advertisement

Quick Links

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will,
if used according to these instructions and properly maintained, give you years of trouble free
performance.
IMPORTANT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents,
WarninGs anD cautions. use tHis ProDuct correctLy anD WitH care for tHe PurPose for WHicH
it is intenDeD. faiLure to Do so May cause DaMaGe anD/or PersonaL inJury anD WiLL inVaLiDate
tHe Warranty. PLease KeeP instructions safe for future use.
1.
safety instructions
 WarninG! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
 WarninG! Disconnect from air supply before refilling, servicing or performing maintenance.
 Maintain the staple gun in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
 Use in suitable clean and tidy work area, free from unrelated materials and ensure there is adequate lighting.
 WarninG! Always wear approved eye and/or face and hand protection when operating the staple gun.
 Remove ill fitting clothing. Remove ties, loose jewellery, and contain and/or tie back long hair.
 Wear appropriate protective clothing and keep hands and body clear of working parts.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the work area.
 Check moving parts alignment on a regular basis.
 Ensure workpiece is secure before operating the staple gun. Never hold a workpiece by hand.
 When the staple gun is put down during pauses in operation ensure that the trigger catch slide is not depressed
by the weight of the staple gun or by placing the staple gun in a restricted position that could put pressure on the
trigger catch slide.
 During extended breaks in operation disconnect the staple gun from the air supply.
 WarninG! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 60-100psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
 Prolonged exposure to vibration from this staple gun may pose a health risk. It is the owner's responsibility
to correctly assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective
equipment.
 DO NOT point the staple discharge outlet at yourself or anyone else. Do not point at animals.
 DO NOT use any power source except an air compressor.
 DO NOT operate the staple gun near any flammable substance or on any container that once contained a
flammable substance.
 DO NOT use the staple gun for a task it is not designed to perform.
 DO NOT operate staple gun if any parts are damaged or missing as this may cause failure and/or personal injury.
 DO NOT carry the staple gun by the hose, or yank the hose from the air supply.
 DO NOT place the staple gun close to your face and do not point at other persons or animals.
 DO NOT operate staple gun when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT carry the staple gun with your finger on the trigger.
 DO NOT direct air from the air hose at yourself or others.
 When not in use, disconnect from air supply and store in a safe, dry, childproof location.
2.
introDuction & sPecification
Professional air stapler with lightweight aluminium body and rubber grip handle. safety trigger device to prevent
accidental firing of staples. supplied in blow mould case with oiler and starter pack of staples.
staple Capacity: . . . . . 10-25mm 18sWG
Max Pressure: . . . . . . 120psi
Air Inlet size: . . . . . . . 1/4"BsP
air staPLe Gun 25MM
Weight: . . . . . . . . . . . . 1.3kg
Original Language Version
INsTRUCTIONs fOR:
caPacity
sa789
MODEl:
sA789
Issue: 2 - 12/11/09

Advertisement

loading

Summary of Contents for Sealey POWER TOOLS SA789

  • Page 1 INsTRUCTIONs fOR: air staPLe Gun 25MM caPacity sa789 Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, MODEl: if used according to these instructions and properly maintained, give you years of trouble free performance.
  • Page 2: Loading The Stapler

    PreParinG staPLe Gun for use air supply Recommended hook-up procedure is shown in fig 1. 3.1.1 Ensure tool air valve (or trigger) is in "off" position before connecting to the air supply. 3.1.2 You will require an air pressure of 90psi, and an air flow according to specification. 3.1.3 ...
  • Page 3 If the air supply does not have an oiler, lubricate the air staple gun daily with a few drops of the air tool oil supplied, dripped into the air inlet before use. To re-order air tool oil use sealey part Nos. ATO500s or ATO1000s.