Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
!
Familiarise yourself with the application and limitations of the riveter, as well as the potential hazards.
"
Maintain the riveter in good condition (use an authorised service agent).
"
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
"
Keep the work area clean, uncluttered and ensure there is adequate lighting.
"
Keep the riveter clean for best and safest performance.
"
WARNING! Always wear approved eye or face protection when operating the riveter.
!
Keep children and unauthorised persons away from the working area.
"
Check moving parts alignment on a regular basis.
"
DO NOT hold the workpiece by hand. Secure unstable workpiece with a clamp, vice or other adequate holding device.
#
Ensure the workpiece is correctly secured before operating the riveter.
"
DO NOT use the riveter for any purpose other than that for which it is designed.
#
DO NOT operate the riveter if any parts are damaged or missing, as this may cause failure and/or personal injury.
#
When not in use return to the case and store in a safe, dry, childproof area.
"
2.
SPECIFICATION AND CONTENTS
Suitable for rivets, rivet nuts and rivet studs in aluminium, steel and stainless steel. Swivel head with 360° movement gives greatly improved
accessibility. Four nozzles for standard rivets, four mandrels for rivet nuts and three mandrels for rivet studs. Supplied with spanners and a
selection of steel rivet nuts.
The AK396 kit is suitable for fitting the following size rivet, rivet nuts and rivet studs.
Rivets
2.4mm (3/32")
Rivet Nuts
M3 x 0.5
Rivet Studs
#
fig. 1
1. Riveting tool
2. Sleeve for mandrels
3. Sleeve for nosepieces
Not shown - four starter packs of 10 steel rivet nuts - M3x0.5, M4x0.7, M5x0.8, M6x1.0.
3.2mm (1/8")
4.0mm (5/32")
M4 x 0.7
M5 x 0.8
M4 x 0.7
M5 x 0.8
CONTENTS
4. Jaw Case
5. Nosepiece (x4)
6. Mandrel for studs (x3)
INSTRUCTIONS FOR:
THREADED NUT RIVET KIT
AK396.V2
Model No:
4.8mm (3/16")
M6 x 1.0
M6 x 1.0
7. Mandrel for nuts (x4)
8. Mandrel holder(x4)
9. Spanners (x3)
AK396.V2 - 1 - 071205
Advertisement
Related Manuals for Sealey AK396.V2
Summary of Contents for Sealey AK396.V2
- Page 1 AK396.V2 Model No: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
- Page 2 Squeeze the riveter handles to compress the stud rivet. When the rivet has formed a retaining bulge against the rear face of the sample, unscrew the mandrel from the stud rivet by turning the knurled end of the draw bar (A) and then screw on a new stud rivet for the next operation. Fig.5 Fig.6 AK396.V2 - 1 - 071205...
- Page 3 INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode. Sole UK Distributor 01284 757500 www.sealey.co.uk Sealey Group, 01284 703534 Bury St. Edmunds, Suffolk. sales@sealey.co.uk email AK396.V2 - 1 - 071205...