Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY
1.1.
ELECTRICAL.
WARNING! It is the user's responsibility to read, understand and comply with the following:
WARNING! THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. Ensure the light is connected to an appropriate electrical on/off switch.
1.1.2. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.
1.1.3. Ensure that cables are always protected against short circuit and overload.
1.1.4. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially power connections, to
ensure that none are loose.
1.1.5. Important: Ensure the voltage marked on the product is the same as the electrical power supply to be used.
1.1.6. DO NOT pull power cable once installed.
1.1.7. DO NOT pull power plugs from sockets by the power cable.
1.1.8. DO NOT use worn or damaged leads, plugs or connections. Replace immediately or have repaired by a qualified Electrician.
1.2.
GENERAL SAFETY.
WARNING! Turn off the mains power supply before servicing or performing any maintenance.
Maintain the light in good condition (Repairs must only be undertaken by a qualified electrician).
Replace or repair damaged parts. Use genuine parts only, unauthorised parts may be dangerous and will invalidate the warranty.
Ensure the light is installed correctly in accordance with these instructions
Ideally the Installation should be away from flammable or combustible materials such as wood, cloth, paper etc.
DANGER! DO NOT direct the light into a persons eyes. This unit has a very intensive light output, which if incorrectly used
could cause eye damage.
DO NOT install the light where it is likely to be knocked or hit.
DO NOT install in bathrooms, shower rooms, sauna or such locations.
DO NOT install near an exhaust outlet. e.g: boiler flue, air conditioning units etc.
DO NOT touch the light when operating, allow to cool before touching. The heat sink behind the lamp can become very hot.
DO NOT use the light without the front glass shield. Avoid touching the glass shield as handling may reduce its serviceable life and
cause the glass to crack.
LED045S
© Jack Sealey Limited
INSTRUCTIONS FOR:
FLOODLIGHTS WITH SWIVEL HEADS, WALL
BRACKET & PIR SENSOR 10 & 20W LED 230V
LED045S,LED046S
MODEL No's :
LED046S
Original Language Version
LED045S,LED046S
Issue:1 14/04/14
Advertisement
Related Manuals for Sealey LED045S
Summary of Contents for Sealey LED045S
- Page 1 LED045S,LED046S MODEL No's : Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 It is now safe to connect to the mains supply. fig.3 fig.1 fig.2 The lamp unit may be pointed down to a maximum of 90º and panned to 30º for the LED046S and 20º left, 40º right for the LED045S (fig.4). 4.10. The detector head may be moved to 90º in each direction.(fig.4) fig.4...
- Page 3 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. Environmental Protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.