Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
WARNING! Ensure Health & Safety, local authority, and general workshop practice
regulations are adhered to when building this shed.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep children and unauthorised persons away from the working area.
DO NOT use the shed for any purpose other than that for which it is designed.
Use appropriate safety clothing including eye protection.
Note! The assembly of this product will require assistance.
Before commencing the assembly, we recommend that you read the instructions thoroughly. Your
new shed comes with all the holes pre drilled to make for fast easy assembly. We recommend
that you assemble the shed using a trestle table or sawhorses and planks. This will ensure that
you are working off the ground and make it easier for you. Assembly is a two person job and
should not be attempted in windy conditions.
Step 1: Check all parts against the component list.
Step 2: Assemble rear wall panels.
Step 3: Assemble side wall panels.
Step 4: Assemble front wall panel.
Step 5: Assemble roof panel.
Step 6: Assemble door.
Step 7: Fit the panels together.
Concrete Slab: It is recommended that your new shed is secured to a concrete slab as per the
specifications in this manual.
INSTRUCTIONS FOR:
GALVANIZED STEEL SHED
MODEL No: GSS1515
Advertisement
Related Manuals for Sealey GSS1515
Summary of Contents for Sealey GSS1515
- Page 1 GALVANIZED STEEL SHED MODEL No: GSS1515 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
- Page 2 Concrete slab: Please ensure that your site is level. It is recommended that your slab is 100mm thick and you use builders plastic and F52 reinforcing mesh. We recommend that you make your slab 100mm bigger than the base dimensions of your shed. This will allow for a 50mm edge around your shed.
- Page 3 Tools Required:...
- Page 4 Step 1：Check all parts against the component list Lay out all parts with number facing outwards and check off against parts list Part Picture Description Component Location Check Sheet 2057x770 zinc- Sheet rear wall left Sheet Sheet 2057x770 zinc- rear wall right Sheet 1977-2057x770 Sheet...
- Page 5 M8 Hexagonal Nut Mid wall brace bracket Channel safety cover Self tapper safety cover (L type) Channel safety cover Rawl bolt (R type) In the unlikely event that you find you are missing a part, please contact your Sealey dealer.
- Page 6 Shed Overview...
- Page 7 Step 2: Assemble rear wall panels. You will find it easier to assemble your shed using sawhorses with timber studs attached ( timber needs to be the same length as the shed ( 1.5 M ) or alternatively, a trestle table. Place 6R and 6L the sheeting on your work table and join together with the self tapping screws per the diagram.
- Page 8 Now fit 31 mid wall channel to the sheeting and position it using the self tapping screws. Please note that the groove should face downwards. Position the top and bottom channels using the self tapping screws as well.
- Page 9 Step 3: Assemble side wall panels Place 2R’ and 7R the sheeting on your work table and tap or slide in 25 top channel and 20A bottom channel. Fix and position the 31 mid wall channel using the self tapping screws. Fix 20A the bottom channel by the self tapping screws but not 25 the top channel in this stage.
- Page 10 Step 4: Assemble the roof panel. Place 8 and 8 the sheeting on your work table and join together with the self tapping screws per the diagram. Now tap or slide in 20A and 20A the channels to the sheeting and fix them using the self tapping screws.
- Page 12 Step 5: Assemble the front wall panel and front door. Place 4 the sheeting on the work table. Fit 20D the top channel, 20E the bottom channel 41B the jamb (There are pre-drilled holes for next step on both 4 and 41B and must be aligned.) and 33R the mid wall channel to the sheeting and fix them using the self tapping screws.
- Page 13 Step 6: Assemble the front wall panel and front door. Fit 5R the pre-assembled door to the front wall panel per the diagram. Use riveter to fix the door into the pre-drilled holes. Fix 70 the pad bolt (but NOT its keeper in this stage) to the pre-drilled holes and rivet or self tapping screws as required.
- Page 14 Step 7: Fit the panels together. Attach the side walls to the back wall, then the front wall, then the roof. Fix all the components using the self tapping screws. Fix 71 the pad bolt keeper with rivets or screws as required. For greater security fit rivets as below.
- Page 15 Now fit the bolt down kit per the diagram. Strengthen your mid wall brace by applying 72 the mid wall brace bracket on each corner. RAWL BOLT...
- Page 16 Apply channel safety cover L type on channel 32 and R type on channel 33R. Apply the self-tapper covers on the screws fixed on the wall to prevent accidental injuries.
- Page 17 Perform the same procedure for the pad lock. Sealey sheds are weatherproof, however, heavy winds with driving rain could cause your shed to leak. Condensation will also occur in some weather conditions such as extreme heat or cold. We would recommend the use of a waterproof sealant to help seal around all joins and wherever you feel that water may get in under these extreme conditions.