Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
8
is replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a EN 60309 (110volt 16amp) plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a EN 60309 (110volt 16amp) plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.1.5.
When a cable extension reel is used it should be fully unwound before connection A cable reel with an RCD fitted is recommended since
any product which is plugged into the cable reel will be protected. The cross-section of the cable on the cable reel must be suitable for the
unit and never lower than the cross-section of the mains cable supplied with the unit.
1.2.
GENERAL SAFETY
Enlist help to place and remove the drill from its working position.
9
DO NOT allow non-essential persons, children or animals into the working area. Establish a cordon below.
8
DO NOT allow the use of this machine except by those who have received suitable training and have read these instructions.
8
If operating above ground level, use suitable staging to provide a safe working platform.
9
DO NOT work from ladders or steps.
8
Use of non-original parts; use of such parts may be dangerous will affect the warranty.
9
WARNING: Always wear approved eye or face protection when operating this drill. Use a face or dust mask if dust is generated.
‰
DO NOT use near flammable gas or liquid, use only in a well lit and ventilated areas.
8
Remove ill fitting clothing, remove ties, watches, rings, and other loose jewellery, and contain long hair.
9
DO NOT operate whilst under the influence of drugs, alcohol or intoxicating medication, or if tired.
8
1.3.
OPERATIONAL SAFETY
ALWAYS attach the drill to the work by means of the nylon security strap and buckle, in case of an electrical supply failure releasing
9
the electro-magnet.
Ensure that the machine is electrically isolated before installing in its working position and switched off before connecting to supply.
9
Ensure drill is switched off and isolated from mains supply before changing bit, or moving its position.
9
Check that the drill and its electric lead is not damaged before use. DO NOT use if any damage is evident.
9
Use non-original parts; use of such parts may be dangerous will affect the warranty.
9
Ensure magnetic switch is in the off position before connecting to mains supply.
9
Only use water as coolant NOT antifreeze.
9
Keep drill dry.
9
If cut-out switch operates follow these steps: turn off power switch, wait for a few minutes, disconnect from mains.
9
DO NOT force the drill with excessive force.
8
© Jack Sealey Limited
60MM MAGNETIC DRILLING MACHINE 110V
MODEL NO:
Wear
Wear protective
protective
footwear
gloves
Original Language Version
MAG60110V
Wear a mask
Wear ear
protection
Brown
Blue(N)
(L)
Cable
Yellow/
restraint
Green
(E)
MAG60110V Issue 1 06/03/20
Advertisement
Related Manuals for Sealey MAG60110V
Summary of Contents for Sealey MAG60110V
- Page 1 MAG60110V MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 If the drill suddenly stops, you must turn off the motor switch immediately. 5.5.6. Once the hole has been cut, back the cutting head back out of the hole and switch off the motor. 5.5.7. Turn off the coolant tap. Original Language Version MAG60110V Issue 1 06/03/20 © Jack Sealey Limited...
- Page 3 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...