Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear eye
instructions
protection
1. sAFetY
1.1.
electricAl sAFetY
WArninG! it is the owner's responsibility to read, understand and comply with the following electrical instructions:
‰
1.1.1.
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An rccB (residual current
circuit Breaker) should be incorporated in the main distribution board. We also recommend that an rcd (residual current device)
is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an
rccB.
You must also read and understand the following instructions concerning electrical safety.
1.1.2.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.3.
the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.4.
ensure that the charger and cable are inspected for wear and damage, to ensure they are safe before connecting to the mains power
supply. if worn or damaged do not use, immediately replace or contact a qualified electrician.
1.1.5.
check cables are always protected against short circuit and overload.
important: check that the voltage marked on the charger is the same as the power supply to be used.
do not pull or carry the charger by the power lead, or pull the plug from the mains socket by the power lead.
8
do not use any other type of charger.
8
do not try to open or dismantle.
8
1.2.
BAtterY sAFetY.
1.2.1.
Charge battery prior to first use. The battery pack will have been shipped in a low charge state.
1.2.2.
use only the charger provided to charge the polisher battery.
do not attempt recharging the battery by means of an engine generator or a dc power source.
8
do not short-circuit the battery by linking both terminals with a metal object, or your fingers etc.
8
do not store the battery (or polisher) in locations where the temperature may exceed 104°f (40°c) such as outside sheds, above
8
heaters, or metal buildings in summer.
WArninG! dispose of spent batteries correctly.
‰
▲
dAnGer! do not attempt to dismantle the battery pack. for safety and environmental reasons do not discard in domestic
waste or by burning. onlY discard or recycle according to local authority regulations.
WArninG! do not allow a leaking battery to contact your person. if you come into contact with battery liquid take the following
‰
immediate action:
a) skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.
b) eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.
1.3.
GenerAl sAFetY
WArninG! ensure that Health & safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
familiarise yourself with the application, limitations and potential hazards of the polisher.
9
WArninG! disconnect from the mains power before changing accessories, servicing or performing any maintenance.
‰
maintain the polisher in good condition (use an authorised service agent).
9
replace or repair damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
WArninG! Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.
‰
Any part that is damaged must be repaired/replaced before the tool is next used.
9
use the polisher in a suitable work area and keep the area clean and tidy and free from unrelated materials. ensure that there is
9
adequate lighting.
Keep the polisher clean for best and safest performance.
9
Before each use check all attachments for condition. if worn or damaged replace immediately.
9
ensure that there are no flammable materials near the work area.
9
WArninG! Wear approved safety eye protection, ear and, if dust is generated, respiratory protection.
‰
maintain correct balance and footing. ensure that the floor is not slippery and wear non-slip shoes.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
© Jack sealey limited
instructions for
cordless lithium-ion polisher Ø240mm 18v
model no:
Wear a mask
Original Language Version
cp2518l
cP2518l | issue 1 25/11/16
Advertisement
Related Manuals for Sealey CP2518L
Summary of Contents for Sealey CP2518L
- Page 1 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 ..............cP2518l Battery: ............18V 1.3Ah li-ion speed: ................ 2500rpm Pad size: ..............Ø240mm replacement battery pack: ........cP2518lBP replacement backing pad: ........ cP2518l.sBP replacement bonnet terry cloth: ......er230P.tB replacement bonnet synthetic fleece: ....cP2518l.Bsf noise power: ..............88dBA noise pressure: .............. 77dBA Vibration: ..............3.325m/s²...
- Page 3 Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid waste authority for recycling information. Battery removal under the Waste Batteries and Accumulators regulations 2009, Jack sealey ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
- Page 4 Please note that the most effective protection is prevention, please refer to the correct use and maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the Hsc website www.hse.gov.uk - Hand-Arm Vibration at Work. Original Language Version cP2518l | issue 1 25/11/16 © Jack sealey limited...