Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
do not cover
instructions
1. safety
1.1.
eLeCtrICaL safety
WarnInG! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
dO nOt pull or carry the appliance by the power cable.
8
dO nOt pull the plug from the socket by the cable.
8
dO nOt use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GeneraL safety
Familiarise yourself with the applications and limitations of the heater.
9
ensure the heater is in good order and condition before use. If in any doubt dO nOt use the unit and contact an electrician.
9
only use recommended attachments and parts. To use unauthorised items may be dangerous and will invalidate your warranty.
9
Check that element guards are in place, undamaged and firmly attached.
9
Keep tools and other items away from the heater when it is in use.
9
Keep the work area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the heater, as it gets very hot.
9
disconnect from mains before moving or attempting any cleaning or maintenance.
9
dO nOt get the heater wet or use in damp or wet locations or areas where there is condensation.
8
dO nOt locate the heater below the power outlet.
8
dO nOt move the heater whilst in operation or even when still warm.
8
dO nOt touch the heater elements, even when cold.
8
dO nOt disassemble the heater for any reason. The heater must be checked by qualified personnel only.
8
dO nOt use this product to perform a task for which it has not been designed.
8
WarnInG! If a fuse blows, ensure it is replaced with an identical fuse type and rating.
‰
When not in use, store the heater carefully in a safe, dry, childproof location.
9
2. IntrOduCtIOn
electric, tripod mounted, heaters with infrared quartz lamps. Reach maximum heat output within seconds of being turned on. Supplied with
power cable and 3-pin plug. A totally dry heat with no condensation, no gas, no fumes, so no smell. Ideal for workshops, bars, forecourts or
gardens and terraces if weather protected.
© Jack Sealey limited
Infrared quartz heaters
LP1500.V2, LP3000
Model no:
Original Language Version
Recommended fuse rating
lP1500.V2 LP3000 Issue 4 (HF) 14/11/18
13 Amp
Advertisement
Related Manuals for Sealey LP1500.V2
Summary of Contents for Sealey LP1500.V2
- Page 1 LP1500.V2, LP3000 Model no: thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 (See fig.5). 4.3.5. The wires at the end of each element should be disconnected from the terminal blocks before attempting to unclip the elements. fig.4 Original Language Version lP1500.V2 LP3000 Issue 4 (HF) 14/11/18 © Jack Sealey limited...
- Page 3 Important: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey Group, Kempson Way, suffolk business Park, bury st edmunds, suffolk. IP32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...