Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Manual
1. SAFETY
WARNING! Turn off, or disconnect from, air supply before servicing or performing any maintenance and when unit is not in use.
Failure to comply with this instruction may damage the unit and will invalidate your warranty.
WARNING! Wear approved ear, eye, hand and respiratory protection when operating the blaster. A full range of personal safety equipment
is available from your Sealey dealer.
Maintain correct balance and ensure firm footing.
Spillages of abrasive material, which may be slippery, must be cleaned up immediately to avoid injury.
Locate blaster in a suitable, well ventilated work area. Keep area clean and tidy and free from unrelated materials, and ensure that
there is adequate lighting.
Maintain the machine in good condition.
Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
Keep the unit clean for best and safest performance.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
Always keep the blast nozzle directed at the workpiece.
If a failure or malfunction occurs disconnect from air supply immediately.
Keep all other persons away from the working area. Contact with high pressure blast or inhaling the dust generated is dangerous.
DO NOT use the blaster for any purpose other than that for which it is designed.
DO NOT operate the blaster if any parts are missing or damaged as this may cause failure and/or personal injury.
DO NOT attempt to clear a blocked nozzle while the unit is pressurised.
DO NOT allow untrained persons to operate the blaster.
DO NOT get the blaster wet or use in damp or wet locations or areas where there is condensation.
DO NOT leave the blaster operating unattended.
DO NOT operate the blaster when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT stand or sit on the blaster.
DO NOT direct air from the air hose at yourself or others.
DO NOT operate system with air supply exceeding 100psi.
DO NOT refill the unit or attempt any maintenance whilst the cylinder is pressurised.
2. INTRODUCTION
Pressurised tank for maximum power. Supplied with 1.5mtr hose & ceramic nozzle with shut off valve. Also includes bayonet air line coupling and
airflow regulator. Soda blasting is especially suitable in the classic car and motorcycle markets as soda will not etch glass and will not warp or
remove metalwork. Surface will be left smooth. Soda also leaves a rust inhibitor behind for up to six weeks. Suitable for use with Sealey Blasting
Soda Model No. SBG25KG.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . PSB10 . . . . . . . . . . . . . . . . . . . . . . . PSB40
Maximum Media Capacity: . . . . . . . . . . . . . . 4.5kg . . . . . . . . . . . . . . . . . . . . . . . . . . 18kg
Maximum Filled Weight: . . . . . . . . . . . . . . . . 10kg. . . . . . . . . . . . . . . . . . . . . . . . . . . 30kg
Air Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . 35-90psi. . . . . . . . . . . . . . . . . . . . . 35-90psi
Air Consumption:. . . . . . . . . . . . . . . . . . . . . . 7cfm. . . . . . . . . . . . . . . . . . . . . . . . . . . 8cfm
Air Inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Ceramic Nozzle Size: . . . . . . . . . . . . . . . . . . 2.4mm . . . . . . . . . . . . . . . . . . . . . . . 2.4mm
Maximum Pressure: . . . . . . . . . . . . . . . . . . . 100psi . . . . . . . . . . . . . . . . . . . . . . . .100psi
Nett Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . 5.5kg . . . . . . . . . . . . . . . . . . . . . . . . . . 13kg
4. ASSEMBLY
4.1. Assemble the soda blaster as in fig.1. Apply PTFE tape to all air connections before tightening.
4.2. Connect the valve block (fig.1.1) to the cylinder by means of the cylinder nut (fig.1.2).
4.3. Screw in the safety valve (fig.1.3), delivery valve (fig.1.4) and push fit connector (fig.1.10).
4.4. Connect the regulator bracket (fig.1.5) to the cylinder by means of the hex. headed bolts provided. Place the neck of the regulator
(fig.1.15) through the bracket and secure with the regulator nut (fig.1.6). Screw in the pressure gauge (fig.1.7), push fit connector (fig.1.10)
and inlet valve. The inlet connector (fig.1.9) screws into the inlet valve.
4.5. Connect the regulator to the valve block using the air inlet tube (fig.1.11). Connect the delivery tube (fig.1.12) to the delivery valve.
NOTE: The delivery valve may be fitted to outer end of the delivery tube, against the nozzle, if preffered.
4.6. To assemble the wheels on the PSB40, pass the axle through the axle supports, place a washer, wheel, washer and 'R' clip in that order on
either side
4.7. Check that all the air connections are tight and free from leaks
4.8. Ensure that the compressor employed has an adequate output to power the soda blaster, and that the piping is of a sufficient diameter to
allow free air flow. DO NOT use a lubricator in the air supply system.
© Jack Sealey Limited
INSTRUCTIONS FOR:
PORTABLE SODA BLASTING KIT
4.5 AND 18kg CAPACITY
MODEL NO'S:
Wear a Face
Wear Protective
Shield
Original Language Version
PSB10,PSB40
Wear Protective
Gloves
Clothing
Wear a Mask
PBS10, PBS40 Version: 1 - 25/02/16
Advertisement
Related Manuals for Sealey PSB10
Summary of Contents for Sealey PSB10
- Page 1 Model No: ......PSB10 ...
- Page 2 Clean with a moist soapy cloth. DO NOT use abrasive or solvent cleaners. Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. Environmental Protection Recycle unwanted materials instead of disposing of them as waste.