Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a
high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT
PLEaSE REaD THESE INSTRUCTIONS CaREFULLy. NOTE THE SaFE OPERaTIONaL REQUIREMENTS, WaRNINGS aND CaUTIONS.
USE THIS PRODUCT CORRECTLy aND WITH CaRE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FaILURE TO DO SO May CaUSE
DaMaGE aND/OR PERSONaL INJURy, aND WILL INVaLIDaTE THE WaRRaNTy. RETaIN THESE INSTRUCTIONS FOR FUTURE USE.
1. SaFETy INSTRUCTIONS
1.1.
ELECTRICaL SaFETy
WaRNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
device (rcd) is used. It is particularly important to use an rcd with portable products that are plugged into a supply which is not protected
by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the Electricity at Work act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & Safety at Work act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. Important: ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the GREEN/yELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) after wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol
to rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and
socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2
GENERaL SaFETy
only power the tool from the mains supply.
disconnect the tool from the mains supply before changing accessories, servicing or performing any maintenance.
maintain tool and accessories in good condition. check moving parts and alignment. If necessary use an authorised service agent.
replace or repair damaged parts using recommended parts. un-authorised parts may be dangerous and will invalidate the warranty.
Wear approved safety eye protection with side shields and a dust mask if generating dust.
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain long hair.
use the tool in a suitable working area, keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.
Prevent body contact with earthed surfaces to avoid electric shock e.g. pipes, radiators, refrigerators etc.
maintain correct balance and footing.
Keep children and unauthorised persons away from the working area.
secure unstable workpiece with a clamp, vice or other adequate holding device.
Avoid unintentional starting. Keep the tool clean for best and safest performance.
When not in use switch tool off and unplug it from the mains supply. store it in the case and put in a dry, childproof area.
DO NOT operate the tool if any parts are missing or damaged as this may cause failure and/or personal injury.
DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT over-reach. ensure the floor is not slippery and wear non-slip shoes.
DO NOT use the tool for a task it is not designed to perform.
DO NOT operate tool where there are flammable liquids or gases.
DO NOT get the tool wet or use in damp or wet locations.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500.
InstructIons for:
MULTIPURPOSE ROTaRy TOOL
E540.V2
model no:
, are fitted with live (brown) and neutral (blue) wires only.
Original Language Version
Yellow & Green
Earth Wire
Blue
Neutral
Wire
FUSE RaTING 3aMP
DO NOT carry the tool by the cable.
DO NOT hold unsecured work in your hand.
DO NOT leave the tool running unattended.
e540.V2
Brown
Live
Wire
Cable
Restraint
Issue: 1 - 12/02/10
Advertisement
Summary of Contents for Sealey E540.V2
- Page 1 (rcd) is used. It is particularly important to use an rcd with portable products that are plugged into a supply which is not protected by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.
- Page 2 WaRRaNTy: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMaTION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, www.sealey.co.uk...