free stats
Download Print this page
Sealey FJ45.V3 Instructions

Sealey FJ45.V3 Instructions

Hydraulic forklift / tractor 4/5 t

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
Important: Read these instRuctions caRefully. note the safe oPeRational ReQuiReMents, WaRninGs and cautions.
use this Jack coRRectly and With caRe foR the PuRPose foR Which it is intended. failuRe to do so May cause
daMaGe and/oR PeRsonal inJuRy and Will invalidate the WaRRanty. Retain these instRuctions foR futuRe use.
1. safety
Wear protective footwear Warning crushing of hands
read the instructions
Ensure that the jack is in good working order. Take action for immediate repair or replacement of damaged
parts. Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the
warranty.
Locate the jack in a suitable, well lit work area.
Keep work area clean and tidy and free from unrelated materials.
Use jack on a level and solid ground, preferably concrete. Avoid tarmacadam as the jack may sink in.
Place wedges under wheels of the vehicle (but ensure wheels of the jack can move freely).
Ensure the vehicle handbrake is engaged, engine/motor is switched off and transmission is in 1st or reverse
gear.
Ensure a minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for
vehicle tilting.
Ensure there are no passengers in the vehicle.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
Only place jack under those lifting points recommended by the vehicle manufacturer (see vehicle handbook).
Check the lifting point is stable and centred on the jack saddle.
Ensure the jack wheels are free to move and that there are no obstructions.
DanGEr: Use the jack for lifting only, not for supporting the lifted load.
Use suitable capacity axle stands under the vehicle before proceeding with any task.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
Use a qualified person to maintain or repair the jack hydraulic system.
do not operate the jack if damaged.
do not allow untrained persons to operate the jack.
do not exceed the rated capacity of the jack.
do not allow the vehicle to move while supported by the jack and do not use the jack to move the vehicle.
do not jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substance.
do not work under the vehicle until axle stands have been correctly positioned.
do not use the jack for purposes other than that for which it is designed.
do not top up hydraulic system with brake fluid. Use hydraulic jack oil only.
do not adjust the safety overload valve.
When not in use store the jack, fully lowered, in a safe, dry, childproof area.
WaRninG! It is very dangerous to go under a vehicle which is supported by a jack even if additional
supports are used. Do not go under a vehicle unless it is supported by adequately rated axle stands.
iMPoRtant! ensure that you can see the saddle and jacking point throughout the jacking operation
in case there is any relative movement.
2. intRoduction
Scissor action jack suitable for automotive, industrial and agricultural applications. Ideal for vehicles with low
ground clearance. Front scissor nose, 4tonne capacity with minimum height of 65mm, allows use under forklifts.
Cylinder cap 5tonne capacity with minimum height of 416mm suits agricultural and other vehicles with high set
jacking points.
Other Text:
iMPoRtant safety WaRninG! alWays use Rated stands.
Please remember a jack is a lifting and lowering device and is not designed to support a load. Never get
underneath a vehicle/load supported only by a jack; your life is at risk. We stock a comprehensive range of axle
stands, for example, please see relevant catalogue section for full details. The jack is not limited to forklift/
tractor/vehicle use only, with many applications in the engineering and construction industries.
3.
sPecification
Capacity: Scissor Nose: . . . . . . . . .4000kg
Cylinder Cap: . . . . . . . . . .5000kg
Min. Scissor Nose Height: . . . . . . . . .65mm
Max. Scissor Nose Height:. . . . . . . .425mm
© Jack Sealey Limited
INSTrUCTIONS FOr:
hydRaulic foRklift / tRactoR
4/5 tonne
fJ45.v3
MOdEL NO:
Min. Cylinder Cap Height: . . . . . . . .416mm
Max. Cylinder Cap Height: . . . . . . . .715mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . .42kg
Original Language Version
Use axle stands
Use wheel chocks
fig.1
See 4.3.
FJ45.V3
Issue: 1 - 28/05/15

Advertisement

loading

Summary of Contents for Sealey FJ45.V3

  • Page 1 MOdEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. Important: Read these instRuctions caRefully. note the safe oPeRational ReQuiReMents, WaRninGs and cautions.
  • Page 2 2) remove filler screw and check that level is up to bottom of filler hole. Add hydraulic oil if necessary. NOTE: Use a good quality jack oil, such as SEALEY HYdrAULIC JACK OIL. WArNING: do not use brake fluid, or any fluid other than hydraulic jack oil as this will cause serious damage to the jack and will ...

This manual is also suitable for:

Fj45