Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure Health & Safety, local authority, and
general workshop practice regulations are adhered to when
using these lockers.
Locate locker in a suitable work area.
Keep the work area clean, uncluttered and ensure there is
adequate lighting.
WARNING! Use locker on level and solid ground, preferably
concrete.
Keep the locker clean and tidy in accordance with good
workshop practice.
Keep children and unauthorised persons away from the work area.
DO NOT use the locker for any purpose other than that for
which it is designed.
DO NOT use the locker outdoors.
DO NOT get the locker wet or use in damp or wet locations or
areas where there is condensation.
DO NOT clean the locker with any solvents which may damage
the surfaces or the protective coating.
2. INTRODUCTION
2.1. Introduction:
A range of lockers suitable for a variety of commercial
applications. Single and two door models fitted with a hanging
bar, single door model also has single shelf. Doors on all models
are ventilated and fitted with cylinder locks, 2 sets of keys
supplied per lock. Supplied flat packed.
2.2. Dimensions:
Width: 380mm, Depth: 450mm, Height: 1850mm.
© Jack Sealey Limited
INSTRUCTIONS FOR:
LOCKERS - 1 DOOR, 2 DOOR, 4 DOOR
MODEL No's:
3. ASSEMBLY
3.1. Lay out the back panel and the two side panels. The side
panels have a cut-out at the front and a lip at the bottom.
Slide the back panel into one of the side panels from the top
(fig.1) and slide it all the way down (fig.2) - note that the shelf
brackets line up.
fig.1
fig.2
fig.2
3.2. Fit the other side panel to the back panel following the same
procedure. Ensure that the side panels are supported in an
upright position so that the panels are not twisted.
3.3. Carefully stand the unit up, again ensuring that the panels are
not twisted, two people may be required for this.
Original Language Version
SL1D.V2, SL2D.V2, SL4D.V2
SL1D.V2, SL2D.V2, SL4D.V2 Issue: 1 - 13/08/13
Advertisement
Related Manuals for Sealey SL1D.V2
Summary of Contents for Sealey SL1D.V2
- Page 1 SL1D.V2, SL2D.V2, SL4D.V2 MODEL No's: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, www.sealey.co.uk 01284 757500 Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, sales@sealey.co.uk 01284 703534 IP32 7AR email Original Language Version © Jack Sealey Limited SL1D.V2, SL2D.V2, SL4D.V2 Issue: 1 - 13/08/13...