free stats
Download Print this page
Sealey SG18.V3 Quick Start Manual

Sealey SG18.V3 Quick Start Manual

Air operated wax injector kit

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! Disconnect the gun from the air supply before changing accessories, servicing or performing any maintenance.
Maintain the gun in good condition. Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Keep the gun clean and rinse out nozzle, quick-release coupling and suction pipes with thinner after use.
9
WARNING! If the gun components become blocked there is a danger of excessive pressure build-up causing the canister to burst.
Locate the gun in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate
9
lighting.
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
9
Keep children and unauthorised persons away from the work area.
9
When not in use ensure that the air supply is turned off and the gun is disconnected.
9
Avoid unintentional operation.
9
Ensure that wax manufacturer's instructions are carefully followed.
9
DO NOT place attachments close to your face (especially eyes, ears, etc.).
8
DO NOT carry by the air hose, or yank the hose or the gun from the air supply.
8
DO NOT use the gun for any purpose other than for which it is designed and DO NOT fill with any other fluid or liquid.
8
DO NOT operate the gun if it is damaged.
8
DO NOT direct air from the air hose at yourself or others.
8
Always wear suitable safety protection when using this equipment. For a full range of goggles, visors, gloves and ear defenders, plus
9
other personal safety equipment. Please refer to the Safety Products section of our catalogue.
When not in use, disconnect from the air supply and store in a safe, dry, childproof area.
9
2. INTRODUCTION
Designed for the application of wax rust inhibitor. Supplied with a selection of lances to enable the wax to be sprayed into body cavities through
small access points.
3. SPECIFICATION
MODEL NO: ........................................................... SG18.V3
Air Consumption: ......................................................... 15cfm
Air Inlet Size: .............................................................1/4"BSP
Recommended Air Pressure: ................................... 60-90psi
4. AIR SUPPLY
4.1.
Recommended hook-up.
4.2.
Ensure that the air valve is in the "off" position before connecting to the air supply.
WARNING! Ensure air supply does not exceed specified figure (see above). Too high an
air pressure and unclean air will shorten the product life due to excessive wear, and may be
dangerous causing possible damage and/or personal injury.
4.3.
Drain the compressor air supply tank daily. Water in the air line will damage equipment and
will invalidate your warranty.
4.4.
Clean the compressor air inlet filter screen weekly.
4.5.
Line pressure should be increased to compensate for
unusually long air hoses (over 8 metres). The minimum
hose bore should be 10mm and fittings must have similar
inside dimensions.
4.6.
Keep hoses away from heat, oil and sharp edges. Check
hoses for wear, and make certain that connectors are
secure.
© Jack Sealey Limited
AIR OPERATED WAX INJECTOR KIT
MODEL NO:
Wear protective
Wear protective
gloves
clothing
Original Language Version
SG18.V3
Wear a mask
fig.2
fig.1
SG18.V3 Issue 1 13/01/20
1

Advertisement

loading

Summary of Contents for Sealey SG18.V3

  • Page 1 SG18.V3 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk...