Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
GENERAL
Ensure the lamp is fully charged before initial use.
DO NOT turn the lamp on when it is being charged.
DO NOT shine directly into your, other person's or animal's eyes.
DO NOT allow children to use the lamp.
DO NOT handle or move the lamp whilst it is being charged.
DO NOT use the lamp if you suspect that the battery or the lamp casing is damaged.
DO NOT LEAVE BATTERY IN A DISCHARGED STATE, RECHARGE BATTERY IMMEDIATELY. BEFORE STORAGE, FULLY
RECHARGE THE BATTERY, SUBSEQUENTLY RECHARGE THE BATTERY AT LEAST ONCE EVERY SIX
MONTHS OF NON-USE.
1.2.
ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING LAMP TO THE POWER SUPPLY.
WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions:
R
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3.
You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply.
If worn or damaged DO NOT use.
IMPORTANT: Check that the voltage marked on the charger plug is the same as the lamp.
V
Uncoil the cable between charger and the lamp.
DO NOT pull the charger plug from the mains socket by the lead.
WARNING! DO NOT use any other type of charger with this product, other than the supplied mains or car charger. Failure to observe
R
this warning could result in injury and or fire and will invalidate the warranty.
DO NOT try to take the charger plug apart.
DO NOT use the charger plug to charge or power any other electrical item.
DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
1.3
BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
R
DO NOT Attempt to open, disassemble, modify or service the battery pack.
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
DO NOT Expose to temperatures above 60°C (140°).
Replace only with the battery pack designated for this product.
Recycle or dispose of used battery as stipulated by local regulation.
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention
2. INTRODUCTION
Unique and innovative 360° swivel and tilt function enables the light source to be positioned in any direction. Exclusive patented design
owned and registered to Sealey. Each lamp houses 10 super bright SMD LEDs providing up to 400 lumens output with 120° spread of light,
illuminating the whole work area. Includes an additional high power 3W LED in the end for use as a directional torch. Features two swivel
hooks and three rubber covered magnets, two on the rear and one on the end, which allow hands free operation. High quality 2.2Ah Lithium-
ion battery for longer life, no memory effect and a much slower discharge than traditional Ni-MH batteries. Supplied with mains and in-car
charger. Also available with Schuko plug - add 'EU' onto the model number of choice.
© Jack Sealey Limited
INSTRUCTIONS FOR
CORDLESS 360° 10SMD+3W RECHARGEABLE INSPECTION
LAMP LITHIUM-ION-SCHUKO PLUG
MODEL NOS: LED360EU, LED360REU (RED), LED360GEU (GREEN)
Original Language Version
LED360EU | Issue 2(L)17/03/15
Advertisement
Related Manuals for Sealey LED360EU
Summary of Contents for Sealey LED360EU
- Page 1 Unique and innovative 360° swivel and tilt function enables the light source to be positioned in any direction. Exclusive patented design owned and registered to Sealey. Each lamp houses 10 super bright SMD LEDs providing up to 400 lumens output with 120° spread of light, illuminating the whole work area.
- Page 2 3. SPECIFICATION fig.1 Model No: ....LED360EU, LED360GEU, LED360REU Battery: ............Li-ion 3.7V-2.2Ah LED Quantity: ..............10+1 Lumen output: .............. 400lm Minimum length: ............260mm Maximum length: ............280mm Operating time: ..3hrs high brightness/6hrs low brightness Charging time: ..............4hrs...
- Page 3 Remove the 6 screws on the back of the lamp. Remove the back casing and disconnect the wiring from the circuit board. Remove the 2 battery mounting screws. Dispose of according to local government guidelines. Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.