Advertisement
Table of Contents
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. sAFetY
i
1.1.
electricAl sAFetY
WArNiNG! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
electrical safety information: it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
importANt: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
do Not pull or carry the appliance by the power cable.
8
do Not pull the plug from the socket by the cable.
8
do Not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.1.5.
Products which require more than 13 amps are supplied without a plug. Contact a qualified electrician to ensure that a suitably rated
supply is available. Ensure that an industrial round pin plug and socket are fitted by a qualified electrician.
1.1.6.
If an extension cable reel is used, ensure that it is fully unwound before connection. Use a reel that includes an RCD, an appliance
will be protected by the RCd. The cable core section is important and should be at least 1.5mm
appropriate for this product. We recommend the use of 2.5mm² core section cable.
1.2.
GeNerAl sAFetY
Familiarise yourself with the application and limitations of the compressor.
9
ensure the compressor is in good order and condition before use. If in any doubt do Not use the unit and contact an electrician/service
9
agent.
WArNiNG! Compressor must only be serviced by an authorised agent. do Not tamper with, or attempt to adjust, pressure switch or
‰
safety valve.
Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air tank pressure has been
9
vented.
Maintain the compressor in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and will invalidate your warranty.
Read the instructions relating to any accessory to be used with this compressor. ensure the safe working pressure of any air appliance
9
used exceeds compressors output pressure. If using a spray gun, check that the area selected for spraying is provided with an air change
system/ventilation.
ensure the air supply valve is turned off before disconnecting the air supply hose.
9
To move a transportable compressor use the handle only. lift the compressor so that the front leg gives enough clearance
9
for manoeuvring but maintain unit's centre of gravity in front of the wheels. do Not attempt to lift or move the compressor by any other
means.
Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
9
Keep tools and other items away from the compressor when it is in use, and keep area clean and clear of unnecessary items.
9
ensure the air hose is not tangled, twisted or pinched.
9
Keep children and unauthorised persons away from the working area.
9
© Jack Sealey limited
compressor 50ltr direct drive 2hp/
4pc Air AccessorY Kit
model no:
Wear ear
Warning:
protection
Hot surface
Automatic start-
Original Language Version
sAc5020e.v3/sAc5020epK.v2
Warning:
Warning:
do Not open
electricity
the air cock
up
before an air
hose is attached
SAC5020E.V3, SAC5020EPK.V2 Issue 1
Indoor
ensure oil level
is correct
use only
before first use
replacement fuse
rating:13A
. ensure that the cable of the reel is
2
13/06/19
Advertisement
Table of Contents
Related Manuals for Sealey AirPower SAC5020E.V3
Summary of Contents for Sealey AirPower SAC5020E.V3
- Page 1 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Ensure that the air vent in the oil filler/breather is free from debris. If the air vent is blocked, pressure can build up in the crankcase causing damage to the compressor and possible personal injury. 4.6. Fit the air filter into the inlet port if required (fig.4). fig.2 fig.1 Original Language Version SAC5020E.V3, SAC5020EPK.V2 Issue 1 13/06/19 © Jack Sealey limited...
-
Page 3: Tool Selection
Thermal cut out: If the unit overheats the thermal cut out will operate and shut the unit down. Allow the unit to cool down then press the reset button, located just inside the pump cover (fig.7). fig.4 fig.3 fig.5 Original Language Version SAC5020E.V3, SAC5020EPK.V2 Issue 1 13/06/19 © Jack Sealey limited... -
Page 4: Maintenance
7.5. recommeNded oil: 7.5.1. Suitable for room temperatures ranging from +5ºC to +25ºC: SeAleY CPo or equivalent SAe 40 compressor oil. 7.5.2. Room temperature below +5ºC: SAe 20 compressor oil. WArNiNG! Never mix different oils and do Not use non-detergent/low quality oils as the compressor may be damaged. -
Page 5: Troubleshooting
Not operate the gauge when you are tired or under the influence of alcohol, drugs or intoxicating medication. do Not operate gauge if parts are missing or the gauge is damaged, as this may cause failure and/or personal injury. © Jack Sealey limited Original Language Version SAC5020E.V3, SAC5020EPK.V2 Issue 1... - Page 6 (fig.12). This provides a vertical fan-shaped pattern which gives maximum, uniform and even coverage when moving the gun back and forth, parallel to the work surface (fig.13). © Jack Sealey limited Original Language Version SAC5020E.V3, SAC5020EPK.V2 Issue 1...
- Page 7 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey Group, Kempson Way, suffolk Business park, Bury st edmunds, suffolk. ip32 7Ar 01284 757500 01284 703534 sales@sealey.co.uk...