Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
1.1.
GENERAL SAFETY
p WARNING! Ensure Health & Safety, local authority and general workshop practice requirements are adhered to when using this equipment.
3 Familiarise yourself with the application and limitations, as well as the potential hazards of the kit.
3 This kit is suitable for cutting/bending copper, brass or thin walled aluminium pipe. DO NOT use for cutting/bending steel pipe.
3 Maintain the kit in good condition (use an authorised service agent).
3 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
3 Locate the kit in a suitable work area. Keep the area clean and tidy and ensure there is adequate lighting.
p WARNING! Always wear approved eye or face protection when using the kit.
3 Keep children and unauthorised persons away from the work area.
3 Secure the pipe to be cut, in a vice.
7 DO NOT use the kit for any purpose other than for which it is designed.
7 DO NOT use the kit if any parts are damaged or missing as this may cause failure and/or personal injury.
7 DO NOT allow untrained persons to use the kit.
7 DO NOT attempt to cut/bend piping when you are tired or under the influence of alcohol, drugs or intoxicating medication.
3 When not in use clean kit components, replace in case and store in a safe, dry, childproof area.
Remember! The safe operation of a vehicle, or other equipment, may well depend on the quality of the bend/cut produced.
Discard any pipe in which the bend/cut is malformed.
2. INTRODUCTION & SPECIFICATION
Composite dies suitable for bending soft metal pipes, with diameters between Ø10mm and Ø22mm, up to 180°. Hand-held, ratchet action tool
has interchangeable pipe guides. Tube cutter included. Supplied in carry-case.
Pipe Bender Capacity: . . . . . . . . . . . . . . . . . . . . . . .Ø10mm-Ø22mm
Tube Cutter Capacity: . . . . . . . . . . . . . . . . . . . . . . . .Ø3mm-Ø32mm
3. CONTENTS & PARTS LIST
Check the content of the kit against the list below. If any item is missing or damaged, contact your supplier immediately.
AK5061:
3.1
Wing Nut (1)
Guides:
12mm/15mm (2),
Dies:
22mm (4),
12mm (7),
Tube Bender (9)
Tube Cutter (10)
ITEM
PART NO.
DESCRIPTION
1.
AK5061.01
WING NUT
2.
AK5061.02
GUIDE 12/15mm
3.
AK5061.03
GUIDE18/22mm
4.
AK5061.04
DIE 22mm
5.
AK5061.05
DIE 18mm
6.
AK5061.06
DIE 15mm
7.
AK5061.07
DIE 12mm
8.
AK5061.08
DIE 10mm
9.
AK5061.09
TUBE BENDER
10.
AK5061.10
TUBE CUTTER
18mm/22mm (3)
18mm (5),
15mm (6),
10mm (8)
RATCHET TUBE AND
Dies: . . . . . . . . . . . . . . . . . . . . .10mm, 12mm, 15mm, 18mm, 22mm
Guides: . . . . . . . . . . . . . . . . . . . . . . . . .12mm, 15mm, 18mm, 22mm
Issue:
Issue Date:
INSTRUCTIONS FOR:
PIPE BENDER
AK5061
MODEL:
1
81104
AK5061 - 1 - 81104
Advertisement
Related Manuals for Sealey AUTO SERVICE AK5061
Summary of Contents for Sealey AUTO SERVICE AK5061
- Page 1 AK5061 MODEL: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS.
- Page 2 INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk. 01284 757500 01284 703534 www.sealey.co.uk...