Advertisement
Quick Links
MoDeL no's
Thank you for purchasing a Sealey jack. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Important: ReaD tHeSe InStRUCtIonS CaRefULLY. note tHe Safe oPeRatIonaL ReQUIReMentS, WaRnInGS anD CaUtIonS.
USe tHIS JaCK CoRReCtLY anD WItH CaRe foR tHe PURPoSe foR WHICH It IS IntenDeD. faILURe to Do So MaY CaUSe
DaMaGe anD/oR PeRSonaL InJURY, anD WILL InvaLIDate tHe WaRRantY. RetaIn tHeSe InStRUCtIonS foR fUtURe USe.
1. SafetY InStRUCtIonS
Disconnect jack from air supply before changing parts, servicing or performing any maintenance.
WaRnInG! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 100-145psi. Required air flow 9.5cfm.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are secure.
Ensure Jack is kept clean and in good working order. Immediately repair or replace damaged parts.
Use recommended parts only. Incorrect parts may be dangerous and will invalidate the warranty.
Use a qualified person to lubricate and maintain the jack. DO NOT use brake fluid to top up system. Use Sealey hydraulic oil only.
Locate jack in a suitable, well lit work area. Keep area clean and tidy and free from unrelated materials.
Use jack on level & solid ground, preferably concrete. Avoid tarmacadam since jack may sink in.
Place wedges under wheels of vehicle (but ensure wheels of jack can freely move).
Ensure the vehicle handbrake is engaged (or in "PARKED" mode), and switch the engine off.
Ensure minimum distance of 0.5m between vehicle tilt & static objects such as doors, walls, etc.
Ensure all non essential persons keep a safe distance and that there are no passengers in the vehicle to be jacked up.
Place jack under vehicle manufacturer's recommended jacking points (see vehicle handbook).
Check that the jacking point is stable and centred on the jack saddle and is free from grease or oil.
Ensure jack wheels are free to move and there are no obstructions.
DanGEr: Use jack for lifting only, NOT for supporting the jacked load. Use correct axle stands under vehicle before proceeding
with task.
DO NOT apply your body weight to the handle during jacking. The handle is only for moving the jack to and from the jacking
location.
DO NOT operate the jack if parts are missing or damaged.
DO NOT exceed the rated capacity of the jack.
DO NOT allow the vehicle to move during jacking and do not use the jack to move the vehicle.
DO NOT jack a vehicle which may result in the spillage of fuel, battery acid, or dangerous
substances.
DO NOT work under the vehicle until Axle Stands have been correctly positioned.
DO NOT use the jack for purposes other that than which it is designed for.
DO NOT adjust the safety overload valve.
DO NOT yank the hose from the air supply, and DO NOT direct air from the air hose at
yourself or others..
Ensure there are no persons or obstructions beneath the vehicle before lowering.
When not in use disconnect jack from the air supply, and store in the down position in a safe, dry, childproof area.
WarnInG! Turn off air supply and de-pressurise the control nozzle before removing the pump unit from any installation or mobile system.
Failure to comply with this instruction may damage the unit and will invalidate your warranty.
2. SPeCIfICatIonS
Note: The maximum heights shown may be extended by use of the extension pin (fig 3A).
Model:
Max capacity . . . . . . . . . 25Tonnes . . . . 35Tonnes. . . . . 30Tonnes . . . . . 80Tonnes . . . 65Tonnes . . . . 30Tonnes
Min height. . . . . . . . . . . . . . 215mm . . . . . . 125mm. . . . . . . 185mm . . . . . . .155mm . . . . . 180mm . . . . . . 360mm
Max height/capacity: . . . . . . . . . . .
Stage 1 (mm/Tonnes). . . . . . 423/25 . . . . . . 240/30. . . . . . . 375/30 . . . . . . . 313/80 . . . . . .358/60 . . . . . . .710/30
Stage 2 (mm/Tonnes). . . . . . . . . . . . . . . . . . 290/20. . . . . . . 470/15 . . . . . . . 371/50 . . . . . .434/35 . . . . . . . . . . . .
Stage 3 (mm/Tonnes). . . . . . . . . . . . . . . . . . 345/10. . . . . . . . . . . . . . . . . . . . 429/30 . . . . . .515/20 . . . . . . . . . . . .
Stage 4 (mm/Tonnes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490/15 . . . . . . . . . . . . . . . . . . . . . . . . .
Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mm. . . . . . . 100mm . . . . . . .100mm . . . . . . 100mm . . . . . . 100mm
Piston stroke . . . . . . . . . . . 108mm . . . . . . 160mm. . . . . . . 185mm . . . . . . .235mm . . . . . 235mm . . . . . . 250mm
Length inc handle. . . . . . . 1840mm . . . . . 2085mm. . . . . . 2085mm . . . . . .2090mm . . . . 2075mm . . . . . 2000mm
Width . . . . . . . . . . . . . . . . . 280mm . . . . . . 280mm. . . . . . . 280mm . . . . . . .317mm . . . . . 317mm . . . . . . 280mm
Working Pressure. . . . . 100-145psi . . . 100-145psi. . . . 100-145psi . . . .100-145psi . . 100-145psi . . . 100-145psi
Required air flow . . . . . . . . . 9.5cfm . . . . . . .9.5cfm. . . . . . . 9.5cfm . . . . . . . 9.5cfm . . . . . . . 9.5cfm . . . . . . . 9.5cfm
Weight . . . . . . . . . . . . . . . . . . 47kg . . . . . . . . 41kg. . . . . . . . . 47kg . . . . . . . . .71kg . . . . . . . 70kg . . . . . . . . 78kg
3. aIR SUPPLY
3.1.
Ensure that the jack pneumatic switch is in the "off" position before connecting to the air supply.
3.2.
You will require an air pressure of more than 100psi (max 145psi) and an air flow of 9.5cfm to get the best performance from this jack.
WaRnInG! Ensure the air supply does not exceed 145psi while operating the jack. Too high an air pressure and unclean air will
3.3.
shorten the products life due to excessive wear, and may be dangerous causing possible damage and personal injury.
3.4.
Drain the air tank daily. Water in the air line will damage the jack.
3.5.
Clean the air inlet filter screen weekly.
3.6.
Keep the air hose between the compressor and the air jack as short as possible, and install an air filter and oiler
(fig 1).
3.7.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum
hose diameter should be 3/8" I.D. and fittings must have the same inside dimensions.
3.8.
Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections
are secure.
MaJ25
MaJ10-35.v2 MaJ15-30.v2
MaJ25 MaJ10-35.v2 MaJ15-30.v2 MaJ15-80.v2 MaJ20-65.v2
Original Language Version
INSTRUCTIONS FOR :
aIR / HYDRaULIC JaCKS
MaJ15-80.v2 MaJ20-65.v2
MAJ25, MAJ10-35.V2, MAJ15-30.V2,
MAJ15-80.V2, MAJ20-65.V2, MAJ30H.V2
MaJ30H.v2
MaJ30H.v2
fig 1.
Issue 3 - 18/02/10
Advertisement
Related Manuals for Sealey MaJ25
Summary of Contents for Sealey MaJ25
- Page 1 Use recommended parts only. Incorrect parts may be dangerous and will invalidate the warranty. Use a qualified person to lubricate and maintain the jack. DO NOT use brake fluid to top up system. Use Sealey hydraulic oil only.
- Page 2 AIR HERE fig 6 jack from the air line and store the jack and air line accordingly. Original Language Version MAJ25, MAJ10-35.V2, MAJ15-30.V2, Issue 3 - 18/02/10 MAJ15-80.V2, MAJ20-65.V2, MAJ30H.V2...
- Page 3 After topping up or pouring off excess oil it may become necessary to purge air from the unit. See section 5.2. note: Use a good quality Jack oil, such as SEALEY HYDRAULIC JACK OIL. WaRnInG! DO NOT use brake fluid, or any fluid other than hydraulic jack fluid as this may cause serious damage to the Jack and will invalidate the warranty! WaRnInG! wear safety goggles.