Advertisement
Quick Links
thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. Safety
waRning! ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
waRning! disconnect from air supply before changing the blade, servicing or performing maintenance.
‰
Maintain the saw in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in suitable clean and tidy work area, free from unrelated materials, ensure that there is adequate lighting.
9
waRning! Always wear approved eye or face and hand protection when operating the saw.
‰
Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the saw.
9
never hold a workpiece by hand. Use a vice or clamps.
9
waRning! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
9
secure.
note:
Prolonged exposure to vibration from this saw poses a health risk. It is the employer's/owner's responsibility to assess the hazard
correctly and issue guidelines for safe periods of use and offer suitable protective equipment.
Do not use any power source except an air compressor.
8
Do not operate saw near any flammable substance or on any container that has held a flammable substance.
8
Do not use the saw for a task it is not designed to perform.
8
Do not operate saw if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Do not carry the saw by the hose, or pull the hose from the air supply.
8
Do not operate saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do not carry the saw with your finger on the trigger.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. intRoDuction
Textured finish to ensure a good grip. Suitable for a variety of bodyshop applications such as cutting through panels, sills, chassis members
etc. Excellent for initial crash-repair preparation when quick removal of damaged panels is required. Fitted with safety trigger device. Suitable
for the professional workshop. Supplied with starter pack of blades.
3. Specification
Model no: .......................................................................................... Sa1006
Air Consumption:.................................................................................. 8.5cfm
Free Speed: ......................................................................................4500rpm
Inlet Size: ...........................................................................................1/4"BSP
Maximum Cutting Capacity: ........................2mm (Steel), 2.5mm (Aluminium)
noise Power/Pressure: ................................................................. 88dB/77dB
Stroke: .................................................................................................7.9mm
Vibration/Uncertainty: ................................................................ 15.5/2.03m/s²
consumable parts:
SA34/B14 ..................................................................14tpi Air Saw Blade (x5)
SA34/B24 ..................................................................24tpi Air Saw Blade (x5)
SA34/B32 ..................................................................32tpi Air Saw Blade (x5)
© Jack Sealey limited
Mini RecipRocating aiR Saw
Model no:
Wear protective
Wear ear
gloves
protection
Original Language Version
Sa1006
Wear a mask
SA1006 Issue 1 18/12/19
Advertisement
Related Manuals for Sealey SA1006
Summary of Contents for Sealey SA1006
- Page 1 Sa1006 Model no: thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 If the cut ends within the sheet material allow the blade to come to a stop before removing the saw from the workpiece. Do not allow the saw to run without load for any length of time as this will damage the bearings. Original Language Version © Jack Sealey limited SA1006 Issue 1 18/12/19...
- Page 3 Guarantee is 24 months from purchase date, proof of which is required for any claim. Sealey group, Kempson way, Suffolk Business park, Bury St edmunds, Suffolk. ip32 7aR 01284 757500 01284 703534 sales@sealey.co.uk...