Advertisement
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1.
ELECTRICAL SAFETY. F
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products that are
plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current
Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business premises, to be tested by
a qualified Electrician at least once a year by using a Portable Appliance Tester (PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3.
Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5.
Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
especially power connections, to ensure that none are loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse. A 13Amp plug may require
a fuse smaller than 13Amps for certain products (subject to 1.1.10. below) see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead. Products such as
welders must not be pulled or carried by their output cables.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired by
a qualified Electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage, cut off
and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
After wiring, check there are no bare wires, that all wires have been correctly connected and that the wire restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked with
this symbol
. To re-wire, connect the brown & blue wires as indicated above. DO NOT connect the brown or blue to the earth terminal.
1.1.10. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD
fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable
reel is important. We recommend that at least 1.5mm
suitable for this product and for others that may be used in the other output sockets, we recommend the use of 2.5mm
1.2
GENERAL SAFETY
! Disconnect the machine from mains power supply before servicing, changing accessories, or performing any maintenance.
! Use genuine accessories and parts only (non recommended accessories and parts may be dangerous, and will invalidate your warranty).
! Maintain the Valet machine in good condition. Use authorised agent for servicing. Keep machine clean, but DO NOT use solvents.
! Ensure the correct filter is firmly in place before operating the Auto Valet. Wrong filters will invalidate your warranty.
! Wear protective clothing and gloves.
% DO NOT allow children or untrained persons to operate the unit.
% DO NOT place attachments close to your face (especially eyes, ears, etc). Do not point the hose end at other persons or animals.
F
WARNING! DO NOT get detergent on flesh. If contact is made wash immediately. NEVER allow detergent near eyes, or mouth. If contact
is made, thoroughly rinse and seek medical advice. If swallowed, seek immediate medical advice. Follow instructions on the detergent container
p
I
DANGER! DO NOT vacuum hot, or glowing ash, cigarette ends, inflammable, explosive, corrosive or dangerous liquids, dusts or substances.
% DO NOT operate the unit without the correct filter for the type of job. Make sure the filter is firmly in place.
s
% DO NOT operate the Green Pump Switch when there is no liquid in the detergent tank. The vacuum motor runs independently of the pump.
% DO NOT leave machine running unattended. Turn power supply OFF, and DO NOT leave the vicinity until motor has come to a complete stop.
% DO NOT operate the Auto Valet while under the influence of drugs, alcohol, or impairing medication, or if you are fatigued.
% DO NOT force the Auto Valet to achieve a task it was not designed to perform.
% DO NOT clean the filters with solvents. When not in use store the valet machine in a safe, dry, childproof location.
INSTRUCTIONS for
Model:
Thank you for purchasing this product. Please follow
these instructions carefully.
FOR CLEANING CAR INTERIORS
WARNING! It is the user’s responsibility to read, understand and comply with the following:
p
VMA 913
section cable but to be absolutely sure that the capacity of the cable reel is
2
Yellow & Green
Earth wire
Blue
Neutral
wire
FUSE RATING
THIS PRODUCT MUST BE FITTED
WITH A:
13 Amp FUSE
section cable.
2
VMA9133 - 3 - 031003
Brown
Live
wire
wire
restraint
Advertisement
Table of Contents
Related Manuals for Sealey AUTO Valet VMA 913
Summary of Contents for Sealey AUTO Valet VMA 913
- Page 1 RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
-
Page 2: Dry Vacuum Cleaning
2. PACKAGE CONTENTS & ASSEMBLY fig 1. 2.1. Carton Content 2.1.1. Carefully unpack the carton content and view the main body of the vacuum cleaner. 2.1.2. Locate the two side clips which hold the motor head in place (fig 1). 2.1.3. -
Page 3: Wet Vacuum Cleaning
5.1.5. Fill the plastic detergent tank with COLD water up to the “MAX” level indicator number 9, or according to the amount you wish to use (fig 12). 5.1.6. Add 20cl of SEALEY “VMR” or Supplied detergent (Note: 20cl is about half a coffee mug). 5.1.7. DO NOT USE ANY OTHER DETERGENT. -
Page 4: After Use
5.3. OPERATING THE AUTO VALET MACHINE WARNING! Test materials for colour fastness, test on an area not normally noticed (i.e. under a car seat). 5.3.1. Plug the machine into the mains power supply. fig 20 5.3.2. Switch the BLACK MOTOR SWITCH “ON” to start the vacuum (fig 20). DO NOT PRESS THE PISTOL TRIGGER AT THIS STAGE. -
Page 5: Troubleshooting
89/336/EEC EMC Directive 93/68/EEC CE Marking Directive For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products CONSUMABLES Part No VMR921 Detergent for Valet Machine ... . . Packs of 12 x 1 Ltr Bottles.