Advertisement
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! DO NOT rest your finger on the trigger when picking up the tool, moving between operating areas and positions or
‰
walking, as resting finger on trigger can lead to inadvertent operation. For tools with selective actuation, always check the
tool before use to ascertain the correct mode is selected.
WARNING! This tool has either selective actuation for contact actuation or continuous contact actuation by actuation mode
‰
selectors or is a contact actuation or continuous actuation contact tool and has been marked with the symbol above (*). Its
intended uses are for production applications such as pallets, furniture, manufactured housing, upholstery and sheathing.
If using this tool in selective actuation mode, always ensure it is in the correct actuation setting.
DO NOT use this tool in contact actuation mode for applications such as closing boxes or crates and fitting transportation
8
safety systems on trailers and lorries.
Be careful when changing from one driving location to another.
9
WARNING! DO NOT use the nail gun if damaged, has missing parts or is thought to be faulty. DO NOT use the tool if the trigger does
‰
not turn the tool on and off. The tool must be repaired. Contact your Service Agent.
WARNING! Remove the battery pack when a fastener jams in the tool, making any adjustments, or storing the tool.
‰
WARNING! Never engage in horseplay with the tool. DO NOT point the tool towards yourself or anyone nearby.
‰
WARNING! Always wear approved eye, face and hand protection when operating the nail gun. Wear a full face shield if stapling produces
‰
metal filings or wood chips.
WARNING! Store idle power tools out of reach of children and DO NOT allow persons unfamiliar with the tool or the instructions to operate
‰
the tool.
WARNING! Always assume that the tool contains fasteners.
‰
Dress properly. DO NOT wear loose clothing or jewellery. Keep hair, clothing and gloves away from moving parts.
9
Use the tool in accordance with these instructions taking into account the working conditions and the work to be performed.
9
WARNING! Keep hands, face, feet and all parts of the body away from the firing head at all times.
‰
DO NOT use the nail gun for a task it is not designed to perform. DO NOT force the tool.
8
DO NOT point the tool towards yourself or anyone nearby. Unexpected triggering will discharge the fastener causing an injury.
8
DO NOT actuate the tool unless it is placed firmly against the workpiece. If the tool is not in contact with the workpiece, the fastener
8
may be deflected away from your target.
DO NOT operate the nail gun near flammable substances or flammable containers.
8
DO NOT use the nail gun unless you have been instructed in its use by a qualified person.
8
DO NOT operate the nail gun if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry the nail gun with your hand on the power trigger in order to avoid unintentional firing.
8
DO NOT load bent or damaged staples into the magazine.
8
DO NOT overreach. Keep proper footing and balance at all times. Ensure the floor is not slippery and wear non-slip shoes.
8
DO NOT drive staples into thin boards or near the corners of the workpiece.
8
▲
DANGER! When putting the nail gun down, ensure that the trigger safety slide is not fouled, risking accidental firing.
Avoid unintentional firing. Keep fingers away from the trigger when not driving staples.
9
WARNING! Disconnect the battery especially when loading staples, when carrying the tool, handing the tool to another person,
‰
leaving the work area, making adjustments to the tool, clearing a jam or whenever it is left unattended.
WARNING! Use caution when clearing a jammed fastener. The mechanism may be under compression and the fastener may be
‰
forcibly discharged while attempting to free jammed condition.
Check the safety mechanism before use. Never use the stapler unless the safety is operating properly, otherwise the stapler could
9
drive a staple unexpectedly.
Place the tool properly on the workpiece. DO NOT drive staples one on top of another or with the tool at too steep an angle. The
9
staples could ricochet.
Keep the work area clean and well lit.
9
Maintain the nail gun in good condition and replace any damaged or worn parts. Check for misalignment or binding of moving
9
parts and any other condition that mat affect the tool's operation, have the tool repaired before use. Use genuine
parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Have the tool serviced by a qualified repair person using only identical replacement parts.
9
Follow all workshop safety rules, regulations, and conditions when using the nail gun.
9
Keep children and non essential persons away from the working area.
9
© Jack Sealey Limited
20V 18G CORDLESS STAPLE/NAIL GUN -
BODY ONLY
MODEL NO:
Wear protective
Wear ear
gloves
protection
Original Language Version
CP20VNG
Keep away from
Keep People
rain
Away
*
CP20VNG
Issue 2 (2,3) 24/05/21
Advertisement
Table of Contents
Related Manuals for Sealey CP20VNG
Summary of Contents for Sealey CP20VNG
- Page 1 CP20VNG MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
-
Page 2: Specification
Features an adjustable drive depth wheel for accurate results. Safety trigger device prevents accidental firing of nails or staples. Requires compatible 20V battery and mains charger, sold separately. 3. SPECIFICATION fig.1 Model No.............. CP20VNG Battery ....20V 2Ah - 6Ah Lithium-ion (not included) Consumable parts: CP20VBP2 - 2Ah Battery, CP20VBP4 - 4Ah Battery, CP20VBP6 - 6Ah Battery Nail capacity ..........10-50mm 18SWG... - Page 3 ; Release the trigger and against the work piece. fig.5 safety contact pin after firing. The safety contact pin must be depressed before the trigger is squeezed. CP20VNG Issue 2 (2,3) 24/05/21 Original Language Version © Jack Sealey Limited...
-
Page 4: Maintenance
Please note that the most effective protection is prevention, please refer to the Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work. Original Language Version CP20VNG Issue 2 (2,3) 24/05/21 © Jack Sealey Limited... -
Page 5: Environment Protection
BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.