Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! Ensure health & safety, local authority and general workshop practice regulations are strictly adhered to when using this
‰
equipment.
Familiarise yourself with product application and limitations, as well as the specific potential hazards perculiar to this product.
9
Maintain pump in good condition. Use an authorised service agent.
9
Replace or repair damaged parts. Use only genuine parts only. Non authorised parts will invalidate warranty.
9
Pump is specifically constructed with Viton seals for transferring AdBlue (diesel engine fuel additive).
9
Can also be used with water, antifreeze, windshield washer fluid or mild detergents.
9
Ensure safety eye protection, protective clothing and gloves are worn when using this product.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip footware.
9
Keep children and unauthorised persons away from the working area.
9
Dispose of waste liquids in accordance with local authority regulations.
9
DO NOT use to extract corrosive fluids.
8
DO NOT dismantle, tamper with or adapt the pump for any other purpose other than for which it is designed.
8
DO NOT use the pump if it had been dropped or mishandled. Check the pump to ensure there is no damage.
8
DO NOT use the pump as a handle to move the fluid drum.
8
Keep the pump clean and store in a safe dry, childproof location.
9
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment.
‰
2. INTRODUCTION
Lever action pump specifically for use with AdBlue®. The dip tube extends from 350mm to 980mm to fit 100L, 205L drums or
barrels, or 1000L IBC tank. Specially constructed with Viton® seals for transferring AdBlue®. 1.6m Delivery hose for hands-free
applications.
Approximately 500ml per stroke discharge. Can also be used with water, antifreeze, windshield washer fluid or mild detergents.
3. SPECIFICATION
Model no: ...................................................................TP6809
Delivery volume: .............................500ml approx. per stroke
4. ASSEMBLY
Unpack the product and check contents. Should there be any damaged or missing parts contact your local supplier immediately.
4.1.
Dip tube assembly
4.2.
Thread dip tube (fig 2-B) into dip tube (fig 2-A) .
4.3.
Thread dip tubes (A + B) (fig 2) into pump (fig 1-1).
4.4.
Loosen joint nut (fig 1-6) and adjust the length of dip tube (fig 1-C) to fit the height of the drum and fix by re-tightening joint nut.
4.5.
Length of assembled dip tubes
4.6.
Dip tube (A + B + C) = 690mm - 980mm.
4.7.
Dip tubes (B + C) = 350mm - 640mm
Note: Dip tube (C) is located within dip tube (B) and is extended by loosening joint nut (fig 1-6) and pulled out to required length.
Re-tighten joint nut.
4.8.
To attach dip tube assembly (B + C)
4.9.
Unscrew dip tube (B) from dip tube (A), and unscrew dip tube (A) from the pump (fig 1-1) and retain.
4.10.
Thread dip tube assembly (B + C) into pump (fig 1-1).
4.11.
Delivery hose attachment
4.12.
Attach delivery hose (fig 1-4) to pump outlet and secure with spring hose clamp (fig1-5).
© Jack Sealey Limited
ADBLUE® LEVER ACTION PUMP
MODEL NO:
Wear protective
Wear protective
gloves
clothing
Original Language Version
TP6809
TP6809 Issue 1 26/01/21
Advertisement
Related Manuals for Sealey ADBLUE TP6809
Summary of Contents for Sealey ADBLUE TP6809
- Page 1 TP6809 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...