hit counter script
Lenovo ThinkSystem D2 Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Enclosure
  5. ThinkSystem D2
  6. Manual

Lenovo ThinkSystem D2 Manual

Enclosure, modular enclosure, modular enclosure for 6u configuration and thinksystem sd530 compute node messages and codes reference
Hide thumbs Also See for ThinkSystem D2:
Table of Contents

Advertisement

Quick Links

ThinkSystem D2 Enclosure, Modular
Enclosure, Modular Enclosure for 6U
Configuration and ThinkSystem SD530
Compute Node
Messages and Codes Reference
Machine Type: 7X20, 7X21, and 7X22

Advertisement

Table of Contents
loading

Related Manuals for Lenovo ThinkSystem D2

Summary of Contents for Lenovo ThinkSystem D2

  • Page 1 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference Machine Type: 7X20, 7X21, and 7X22...
  • Page 2 Before using this information and the product it supports, be sure to read and understand the safety information and the safety instructions, which are available at: http://thinksystem.lenovofiles.com/help/topic/safety_documentation/pdf_files.html In addition, be sure that you are familiar with the terms and conditions of the Lenovo warranty for your server, which can be found at: http://datacentersupport.lenovo.com/warrantylookup Thirteenth Edition (April 2022) ©...

  • Page 3: Table Of Contents

    Index ....219 Chapter 4. UEFI events ..153 UEFI events organized by severity ..153 © Copyright Lenovo 2017, 2022...
  • Page 4 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 5: Chapter 1. Introduction

    Lenovo XClarity Provisioning Manager (although these events are not stored in the event log). Use this section to view the events that can be generated by Lenovo XClarity Controller, UEFI, or the Lenovo XClarity Provisioning Manager. For each event, a user action is available to help you understand what must be done to resolve the issue.
  • Page 6 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 7: Chapter 2. Smm2 Events

    2. If 12V_SENSE warning is still asserted, replace SMM module. • 0201001B: 3V3_SENSE: Voltage sensor, warning event was asserted, reading value %V (Threshold Asserted when voltage sensed on 3.3V power rail is lower than lower critical threshold or higher than upper critical threshold © Copyright Lenovo 2017, 2022...
  • Page 8 Asserted when voltage sensed on 12V power rail is lower than lower critical threshold or higher than upper critical threshold Severity: Critical ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 9 User Action: 1. Reseat SMM module. 2. If 12V_SENSE error is still asserted, replace SMM module. • 0201021B: 3V3_SENSE: Voltage sensor, critical event was asserted, reading value %V (Threshold Asserted when voltage sensed on 3.3V power rail is lower than lower critical threshold or higher than upper critical threshold Severity: Critical User Action:...
  • Page 10 • 0201071E: 1V2_SENSE: Voltage sensor, warning event was asserted, reading value %V (Threshold Asserted when voltage sensed on 1.2V power rail is higher than upper non-critical threshold. Severity: Informational ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 11 User Action: 1. Reseat SMM module. 2. If 1V2_SENSE warning is still asserted, replace SMM module. • 0201071F: 1V15_SENSE: Voltage sensor, warning event was asserted, reading value %V (Threshold Asserted when voltage sensed on 1.15V power rail is higher than high non-critical threshold. Severity: Informational User Action: 1.
  • Page 12 1. If warning is not de-asserted after several minutes, check all five fans are installed. 2. Reseat fan module a couple of times. If error still persist, replace fan module. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 13 • 04010014: FAN_TACH_3A: Fan sensor, warning event was asserted, reading value %RPM (Threshold %RPM) Asserted when Fan tach reading is below warning threshold RPM. Severity: Warning User Action: 1. If warning is not de-asserted after several minutes, check all five fans are installed. 2.
  • Page 14 • 04010215: FAN_TACH_3B: Fan sensor, critical event was asserted, reading value %RPM (Threshold %RPM) Asserted when Fan tach reading is below error threshold RPM. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 15 Severity: Critical User Action: 1. If critical is not de-asserted after several minutes, check all five fans are installed. 2. Reseat fan module a couple of times. If error still persist, replace fan module. • 04010216: FAN_TACH_4A: Fan sensor, critical event was asserted, reading value %RPM (Threshold %RPM) Asserted when Fan tach reading is below error threshold RPM.
  • Page 16 1. Check the inventory power of all powered on nodes to see if the summary over current power bank – Replace the node with light configuration ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 17 – Install the PSU with higher capacity • 080701CB: PSU_FFS: Power Supply, transition to Non-Critical from OK was asserted. All power supply fans run at full speed. Severity: Warning User Action: 1. Ensure the room temperature remains at the required level. 2.
  • Page 18 The power supply is not supporting low line input but initially applied with a low line voltage Severity: Informational User Action: Information only; no action is required. • 080708AB: PS_0_OUTPUT_FAIL: Power Supply, Informational was asserted. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 19 The zero output functions abnormally Severity: Informational User Action: Information only; no action is required. • 080801E0: PS1: Power Supply, Device Inserted / Device Present was asserted. The PSU is installed in the indicated slot. Severity: Informational User Action: Information only; no action is required. •...
  • Page 20 Severity: Critical User Action: 1. Check power supply LEDs – If AC LED is not lit, check power cord and input voltage. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 21 – If DC LED is not lit, remove and reinstall power supply. – If error LED is lit, replace the power supply. 2. If fault recurs, please call service. • 086F0188: PS1_12V_OV_ERR: Power Supply, Power Supply Failure detected was asserted. The 12V output voltage reaches overvoltage lockout limit Severity: Critical User Action:...
  • Page 22 – If error LED is lit, replace the power supply. 2. If fault recurs, please call service. • 086F0191: PS2_VIN_UV_ERR: Power Supply, Power Supply Failure detected was asserted. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 23 The input voltage drops to the Turn-Off voltage Severity: Critical User Action: 1. Check power supply LEDs – If AC LED is not lit, check power cord and input voltage. – If DC LED is not lit, remove and reinstall power supply. –...
  • Page 24 – If error LED is lit, replace the power supply. 2. If fault recurs, please call service. • 086F01AC: PS1_INTRL_OC_ERR: Power Supply, Power Supply Failure detected was asserted. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 25 The power supply experiences an internal fault caused overcurrent condition Severity: Critical User Action: 1. Check power supply LEDs – If AC LED is not lit, check power cord and input voltage. – If DC LED is not lit, remove and reinstall power supply. –...
  • Page 26 Information only; no action is required. • 146F0231: SMM_RESET: Button Or Switch, Reset Button pressed was asserted. A event indicate SMM system reboot Severity: Informational ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 27 User Action: Information only; no action is required. • 146F0232: USER_RST_DEFAULT: Button Or Switch, Reset Button pressed was asserted. User reset the system configuration to default setting Severity: Informational User Action: Information only; no action is required. • 1509002D: PIOR_R_3V3_PG: Module Or Board, Device Disabled was asserted. A event indicate right PIOR 3.3V power good fault Severity: Critical User Action:...
  • Page 28 • 180708CE: HI_PCI_NOACSTIC: Chassis, Informational was asserted. The acoustic mode has been disabled due to high power PCIe card be installed Severity: Informational User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 29 Information only; no action is required. • 1D6F0030: SMM_POWER_ON: System Boot Initiated, Initiated by power up was asserted. A event indicate SMM system power on Severity: Informational User Action: Information only; no action is required. • 21070150: NODE1_1ST_NOPERM: Slot Or Connector, transition to Non-Critical from OK was asserted.
  • Page 30 • 21070157: NODE4_2ND_NOPERM: Slot Or Connector, transition to Non-Critical from OK was asserted. OS failed to get the power permission to power on the compute node. Severity: Warning ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 31 User Action: 1. Check the PSU configuration 2. Check FAN status 3. Reset BMC 4. If error recurs, reseat compute node 5. If error recurs, replace the compute node • 21070164: NODE1_NO_COMM: Slot Or Connector, transition to Non-Critical from OK was asserted. The BMC has no response over 1 minute, system fans are ramped to prevent the compute node from potential thermal conditions Severity: Warning...
  • Page 32 2. Reset the XCC 3. Check the SEL if other Fail-Safe SEL asserted • 2107066A: NODE3_FS_NORESP: Slot Or Connector, transition to Non-recoverable was asserted. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 33 The BMC has no response over 7 minutes after the client OS is power on, no further action will be taken. Severity: Critical User Action: 1. Please shutdown the OS 2. Reset the XCC 3. Check the SEL if other Fail-Safe SEL asserted •...
  • Page 34 • 2107084B: NODE4_RESEAT: Slot Or Connector, Informational was asserted. Performed a virtual reseat to AC cycle the compute node Severity: Informational User Action: Information only; no action is required. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 35 • 2107084C: NODE1_RESET: Slot Or Connector, Informational was asserted. Performed BMC reset on the compute node Severity: Informational User Action: Information only; no action is required. • 2107084D: NODE2_RESET: Slot Or Connector, Informational was asserted. Performed BMC reset on the compute node Severity: Informational User Action: Information only;...
  • Page 36 Re-configure the power cap value of the compute node from web GUI or IPMI command • 216F005B: NODE4_CAP_LOW: Slot Or Connector, Fault Status asserted was asserted. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 37 The restored power cap value is invalid since it is lower than current power cap boundary Severity: Critical User Action: Re-configure the power cap value of the compute node from web GUI or IPMI command • 216F005C: NODE1_CAP_FAIL: Slot Or Connector, Fault Status asserted was asserted. Failed to set power cap to compute node Severity: Critical User Action:...
  • Page 38 Severity: Critical User Action: 1. Changing items in UEFI F1 Setup to force PTU running again – device is enabled / disabled ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 39 – memory speed or link disable setting changed – UPI speed or link disable setting changed – C1E, C-state, or P-state setting changed – # of enabled CPU cores changed – Turbo setting changed – CPU freq limit changed 2. If the error recurs, replace the node •...
  • Page 40 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 41: Chapter 3. Xclarity Controller Events

    Chapter 3. XClarity Controller events When a hardware event is detected by the Lenovo XClarity Controller on the server, the Lenovo XClarity Controller writes that event in the system-event log on the server. Notes: Event identifier (ID) is a unique identifier used to search for XCC events. The event message may have one or more arguments, which could be replaceable text of FRU name or sensor name to identify the failed component.

  • Page 42: Xcc Events That Automatically Notify Support

    If you have configured this function and this field is set to Yes, Lenovo Support will be notified automatically if the event is generated. While you wait for Lenovo Support to call, you can perform the recommended actions for the event.

  • Page 43: Xcc Events Organized By Severity

    Table 1. Events that automatically notify Support (continued) Message String Event ID FQXSPIO0011N An Uncorrectable Error has occurred on [SensorElementName]. FQXSPPW0002L [PowerSupplyElementName] has Failed. FQXSPPW0035M Numeric sensor [NumericSensorElementName] going low (lower critical) has asserted. FQXSPPW0047M Numeric sensor [NumericSensorElementName] going high (upper critical) has asserted.
  • Page 44 Informational FQXSPEM4001I The [arg1] on system [arg2] is 75% full. Informational FQXSPEM4002I The [arg1] on system [arg2] is 100% full. Informational ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 45 Table 2. Events organized by severity (continued) Message String Severity Event ID FQXSPEM4003I LED [arg1] state changed to [arg2] by [arg3]. Informational FQXSPEM4004I SNMP [arg1] enabled by user [arg2] . Informational FQXSPEM4005I SNMP [arg1] disabled by user [arg2] . Informational FQXSPEM4006I Alert Configuration Global Event Notification set by user [arg1]: Informational...
  • Page 46 Error deassertion. FQXSPIO2003I System [ComputerSystemElementName] has recovered from a Informational diagnostic interrupt. FQXSPIO2004I Bus [SensorElementName] has recovered from a bus timeout. Informational ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 47 Table 2. Events organized by severity (continued) Message String Severity Event ID FQXSPIO2006I System [ComputerSystemElementName] has recovered from an NMI. Informational FQXSPIO4001I GPU Board Status was changed by [arg1] of [arg1]. Informational FQXSPIO4002I GPU Board Status was recovered by [arg1] of [arg1]. Informational FQXSPMA2005I The System [ComputerSystemElementName] has detected a POST...
  • Page 48 LAN over USB [arg1] by user [arg2]. Informational FQXSPNM4047I LAN over USB Port Forwarding set by user [arg1]: ExternalPort= Informational [arg2], USB-LAN port=[arg3]. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 49 User [arg1] has set the SMTP Server reverse-path to [arg2]. Informational FQXSPNM4052I DHCP specified hostname is set to [arg1] by user [arg2]. Informational FQXSPNM4053I DNS discovery of Lenovo XClarity Administrator has been [arg1] by Informational user [arg2]. FQXSPNM4054I The hostname from DHCP is [arg1] by user [arg2]. Informational FQXSPNM4055I The hostname from DHCP is invalid.
  • Page 50 FQXSPPP4039I The server stayed powered off because the power restore policy is set Informational to restore previous power state.. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 51 Table 2. Events organized by severity (continued) Message String Severity Event ID FQXSPPP4040I The server was powered off via Platform Event Filter. Informational FQXSPPP4041I The server was powered off via Real Time Clock (scheduled power Informational off). FQXSPPP4042I Management Controller [arg1] reset was initiated due to Power-On- Informational Reset.
  • Page 52 LDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], Informational BindingMethod=[arg4], EnhancedRBS=[arg5], TargetName=[arg6], GroupFilter=[arg7], GroupAttribute=[arg8], LoginAttribute=[arg9]. FQXSPSE4011I Secure Web services (HTTPS) [arg1] by user [arg2]. Informational ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 53 Table 2. Events organized by severity (continued) Message String Severity Event ID FQXSPSE4012I Secure CIM/XML(HTTPS) [arg1] by user [arg2]. Informational FQXSPSE4013I Secure LDAP [arg1] by user [arg2]. Informational FQXSPSE4014I SSH [arg1] by user [arg2]. Informational FQXSPSE4015I Global Login General Settings set by user [arg1]: Informational AuthenticationMethod=[arg2], LockoutPeriod=[arg3], SessionTimeout=[arg4].
  • Page 54 User [arg1] role set to [arg2] by user [arg3] from [arg4] at IP address [arg5]. FQXSPSE4061I User [arg1] custom privileges set: [arg2][arg3][arg4][arg5][arg6][arg7] Informational [arg8][arg9] by user [arg10] from [arg11] at IP address [arg12]. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 55 Table 2. Events organized by severity (continued) Message String Severity Event ID FQXSPSE4062I The system guard snapshot is captured by user [arg1] from [arg2] at Informational IP address [arg3]. FQXSPSE4063I The system guard configuration is updated: status=[arg1], hardware Informational inventory=[arg2] and action=[arg3] by user [arg4] from [arg5] at IP address [arg6].
  • Page 56 Numeric sensor [NumericSensorElementName] going low (lower non- Warning critical) has asserted. FQXSPPW0057J Sensor [SensorElementName] has transitioned from normal to non- Warning critical state. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 57 Table 2. Events organized by severity (continued) Message String Severity Event ID FQXSPSD0002G Failure Predicted on [StorageVolumeElementName] for array Warning [ComputerSystemElementName]. FQXSPUN0009G Sensor [SensorElementName] has asserted. Warning Warning FQXSPUN0018J Sensor [SensorElementName] has transitioned from normal to non- critical state. FQXSPUN0026G Device [LogicalDeviceElementName] has been added.

  • Page 58: List Of Xclarity Controller Events

    Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0027 User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 59 Information only; no action is required • FQXSPBR4001I: Running the backup Management Controller [arg1] main application. This message is for the use case where a Management Controller has resorted to running the backup main application. Severity: Warning Serviceable: No Automatically notify Support: No Alert Category: System - other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0030...
  • Page 60 SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0137 User Action: Complete the following steps until the problem is solved: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 61 1. Turn off the server and disconnect it from the power source. You must disconnect the server from AC power cycle to reset the XCC. 2. After 45 seconds, reconnect the server to the power source and turn on the server. 3.
  • Page 62 Alert Category: Critical - Temperature SNMP Trap ID: 0 CIM Prefix: PLAT CIM ID: 0494 User Action: Complete the following steps: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 63 1. Check the event log of system management module and xClarity Controller for any fan or cooling- related issues or power-related issues. 2. Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
  • Page 64 This message is for the use case when an implementation has detected an Upper Non-critical sensor going high has deasserted. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 65 Severity: Info Serviceable: No Automatically notify Support: No Alert Category: Warning - Temperature SNMP Trap ID: 12 CIM Prefix: PLAT CIM ID: 0491 User Action: Information only; no action is required • FQXSPCA2009I: Numeric sensor [NumericSensorElementName] going high (upper critical) has deasserted.
  • Page 66 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0128 User Action: Information only; no action is required ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 67 • FQXSPCN4002I: User [arg1] has terminated an active console session. A user has terminated an active console session Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0145 User Action: Information only;...
  • Page 68 Information only; no action is required • FQXSPDM4006I: User [arg1] has generated a new encryption key and certificate signing request for the TKLM client. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 69 User generated a new encryption key and certificate signing request for the TKLM client Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0149 User Action: Information only; no action is required •...
  • Page 70 • FQXSPEM4004I: SNMP [arg1] enabled by user [arg2] . A user enabled SNMPv1 or SNMPv3 or Traps Severity: Info Serviceable: No Automatically notify Support: No ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 71 Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0073 User Action: Information only; no action is required • FQXSPEM4005I: SNMP [arg1] disabled by user [arg2] . A user disabled SNMPv1 or SNMPv3 or Traps Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID:...
  • Page 72 Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0201 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 73 User Action: Information only; no action is required • FQXSPEM4013I: Battery error was detected by RAID controller. The battery unit needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5]) Battery error was detected by RAID controller Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0202 User Action:...
  • Page 74 Fan problem detected with the enclosure/chassis Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 75 SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0209 User Action: Information only; no action is required • FQXSPEM4022I: Enclosure/Chassis power supply has problem. Please check the enclosure/ chassis unit power supply for correct operation.([arg1],[arg2],[arg3],[arg4],[arg5]) Enclosure/Chassis power supply has problem Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 76 Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0220 User Action: Information only; no action is required ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 77 • FQXSPEM4029I: All PCIe slots on [arg1] may not be functional based upon your current CPU population. PCIe not be functional Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0221 User Action: Information only;...
  • Page 78 Information only; no action is required • FQXSPFC4003I: UEFI deployment boot mode is enabled for NextBoot. UEFI deployment boot mode is enabled for NextBoot ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 79 Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0197 User Action: Information only; no action is required • FQXSPFC4004I: UEFI deployment boot mode is enabled for NextAc. UEFI deployment boot mode is enabled for NextAC Severity: Info Serviceable: No...
  • Page 80 CIM Prefix: PLAT CIM ID: 0240 User Action: Check http://support.lenovo.com/ for TECH tips or firmware updates that might correct the error. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 81 1. Make sure that all I/O expansion adapters have correct and matching levels of device drivers and firmware. 2. Check the event log of system management module(SMM) or xClarity Controller for additional information about failing components. 3. If there are no entries related to the error in the event log, contact service. •...
  • Page 82 Serviceable: Yes Automatically notify Support: No Alert Category: Critical - Temperature SNMP Trap ID: 0 CIM Prefix: PLAT CIM ID: 0146 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 83 User Action: Complete the following steps until the problem is solved: 1. Check the event log of system management module and xClarity Controller (XCC) for any fan- or cooling-related issues. 2. Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
  • Page 84 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0003 User Action: Information only; no action is required ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 85 • FQXSPNM4002I: Ethernet Duplex setting modified from [arg1] to [arg2] by user [arg3]. This message is for the use case where A user modifies the Ethernet Port duplex setting. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0004 User Action:...
  • Page 86 This message is for the use case where a DHCP server fails to assign an IP address to a Management Controller. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 87 Severity: Warning Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0013 User Action: Complete the following steps until the problem is solved: 1. Make sure that the XCC network cable is connected. 2.
  • Page 88 Information only; no action is required • FQXSPNM4018I: DDNS setting changed to [arg1] by user [arg2]. DDNS setting changed by user ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 89 Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0045 User Action: Information only; no action is required • FQXSPNM4019I: DDNS registration successful. The domain name is [arg1]. DDNS registation and values Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 90 IPv6 DHCP assignment method is disabled by user Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0053 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 91 User Action: Information only; no action is required • FQXSPNM4027I: IPv6 stateless auto-configuration disabled by user [arg1]. IPv6 statless auto-assignment method is disabled by user Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0054 User Action: Information only;...
  • Page 92 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0062 User Action: Information only; no action is required ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 93 • FQXSPNM4035I: Web-HTTP port number changed from [arg1] to [arg2] by user [arg3]. A user has modified the Web HTTP port number Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0063 User Action: Information only;...
  • Page 94 • FQXSPNM4043I: SMTP Server set by user [arg1] to [arg2]:[arg3]. A user configured the SMTP server Severity: Info Serviceable: No Automatically notify Support: No ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 95 Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0086 User Action: Information only; no action is required • FQXSPNM4044I: Telnet [arg1] by user [arg2]. A user enables or disables Telnet services Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0087...
  • Page 96 User set SMTP Server reverse-path address Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 97 SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0216 User Action: Information only; no action is required • FQXSPNM4053I: DNS discovery of Lenovo XClarity Administrator has been [arg1] by user [arg2]. DNS discovery of Lenovo XClarity Administrator Severity: Info Serviceable: No...
  • Page 98 CIM Prefix: IMM CIM ID: 0028 User Action: If there was no operating-system error, complete the following steps until the problem is solved: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 99 1. Reconfigure the watchdog timer to a higher value. 2. Make sure that the IMM Ethernet-over-USB interface is enabled. 3. Reinstall the RNDIS or cdc_ether device driver for the operating system. 4. Disable the watchdog. 5. If there was an operating-system error, check the integrity of the installed operating system. •...
  • Page 100 This message is for the use case where Host Admin password cleared. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 101 SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0234 User Action: Information only; no action is required • FQXSPOS4009I: OS Crash Video Captured. This message is for the use case where OS Crash Video Captured. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22...
  • Page 102 Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0084 User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 103 Information only; no action is required • FQXSPPP4005I: The power cap value changed from [arg1] watts to [arg2] watts by user [arg3]. Power Cap values changed by user Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0113 User Action: Information only;...
  • Page 104 • FQXSPPP4013I: Static Power Savings mode has been turned on by user [arg1]. Static Power Savings mode turned on by user Severity: Info Serviceable: No ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 105 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0121 User Action: Information only; no action is required • FQXSPPP4014I: Static Power Savings mode has been turned off by user [arg1]. Static Power Savings mode turned off by user Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 106 Automatically notify Support: No Alert Category: Warning - Power SNMP Trap ID: 164 CIM Prefix: IMM CIM ID: 0131 User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 107 Information only; no action is required • FQXSPPP4022I: The server was restarted for an unknown reason. The server was restarted for an unknown reason Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0166 User Action: Information only;...
  • Page 108 CIM Prefix: IMM CIM ID: 0173 User Action: Information only; no action is required • FQXSPPP4030I: The server was reset via Platform Event Filter. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 109 Server was reset via Platform Event Filter Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0174 User Action: Information only; no action is required • FQXSPPP4031I: The server was power-cycled via Platform Event Filter. Server was power-cycled via Platform Event Filter Severity: Info Serviceable: No...
  • Page 110 Server stayed powered off because the power restore policy is set to always restore. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 111 SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0182 User Action: Information only; no action is required • FQXSPPP4039I: The server stayed powered off because the power restore policy is set to restore previous power state.. Server stayed powered off because the power restore policy is set to restore previous power state. Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 112 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0021 User Action: Information only; no action is required ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 113 • FQXSPPP4048I: Attempting to AC power cycle server [arg1] by user [arg2]. AC power cycle server Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0227 User Action: Information only;...
  • Page 114 Automatically notify Support: No Alert Category: Critical - Temperature SNMP Trap ID: 0 CIM Prefix: PLAT CIM ID: 0037 User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 115 Information only; no action is required • FQXSPPU2002I: The Processor [ProcessorElementName] is no longer operating in a Degraded State. This message is for the use case when an implementation has detected a Processor is no longer running in the Degraded state. Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 116 Serviceable: No Automatically notify Support: No Alert Category: System - Power Off SNMP Trap ID: 23 CIM Prefix: PLAT CIM ID: 0106 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 117 User Action: Information only; no action is required • FQXSPPW0009I: [PowerSupplyElementName] has been Power Cycled. This message is for the use case when an implementation has detected a Power Unit that has been power cycled. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: CIM Prefix: PLAT CIM ID: 0108...
  • Page 118 This message is for the use case when an implementation has detected a Sensor transitioned to critical from less severe. Severity: Error ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 119 Serviceable: Yes Automatically notify Support: Yes Alert Category: Critical - Voltage SNMP Trap ID: 1 CIM Prefix: PLAT CIM ID: 0522 User Action: Reseat the faulty node in D2 enclosure (AC cycle). 1. Check if multiple nodes within the D2 enclosure are reporting SysBrd Vol fault: 2.
  • Page 120 This message is for the use case when an implementation has detected a Power Unit that has been Enabled. Severity: Info Serviceable: No Automatically notify Support: No ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 121 Alert Category: System - Power On SNMP Trap ID: 24 CIM Prefix: PLAT CIM ID: 0107 User Action: Information only; no action is required • FQXSPPW2031I: Numeric sensor [NumericSensorElementName] going low (lower non-critical) has deasserted. This message is for the use case when an implementation has detected a Lower Non-critical sensor going low has deasserted.
  • Page 122 CIM Prefix: IMM CIM ID: 0243 User Action: Information only; no action is required • FQXSPSD0000I: The [StorageVolumeElementName] has been added. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 123 CIM Prefix: PLAT CIM ID: 0164 User Action: Complete the following steps: 1. Check the Support Portal(http://support.lenovo.com/)for service bulletins and TECH tips and firmware update related to your drive. 2. Check for any other RAID-related error. 3. Replace the drive.
  • Page 124 This message is for the use case when an implementation has detected a Drive has been Removed. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 125 CIM Prefix: PLAT CIM ID: 0163 User Action: Complete the following steps until the problem is solved: 1. If drive was intentionally removed, make sure that there is a filler in the drive bay. 2. Make sure that the drive is correctly seated. 3.
  • Page 126 • FQXSPSE4001I: Remote Login Successful. Login ID: [arg1] using [arg2] from [arg3] at IP address [arg4]. This message is for the use case where a user successfully logs in to a Management Controller. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 127 Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Remote Login SNMP Trap ID: 30 CIM Prefix: IMM CIM ID: 0014 User Action: Information only; no action is required • FQXSPSE4002I: Security: Userid: [arg1] using [arg2] had [arg3] login failures from WEB client at IP address [arg4].
  • Page 128 • FQXSPSE4009I: LDAP Server configuration set by user [arg1]: SelectionMethod=[arg2], DomainName=[arg3], Server1=[arg4], Server2=[arg5], Server3=[arg6], Server4=[arg7]. A user changed the LDAP server configuration Severity: Info Serviceable: No ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 129 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0076 User Action: Information only; no action is required • FQXSPSE4010I: LDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], EnhancedRBS=[arg5], TargetName=[arg6], GroupFilter=[arg7], GroupAttribute=[arg8], LoginAttribute=[arg9]. A user configured an LDAP Miscellaneous setting Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 130 User Action: Information only; no action is required • FQXSPSE4017I: User [arg1] created. A user account was created Severity: Info Serviceable: No ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 131 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0100 User Action: Information only; no action is required • FQXSPSE4018I: User [arg1] removed. A user account was deleted Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0101...
  • Page 132 • FQXSPSE4025I: SSH Client key removed from user [arg1] by user [arg2] from [arg3] at IP address [arg4]. User removed an SSH Client key Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 133 SNMP Trap ID: CIM Prefix: IMM CIM ID: 0108 User Action: Information only; no action is required • FQXSPSE4026I: Security: Userid: [arg1] had [arg2] login failures from a CIM client at IP address [arg3]. This message is for the use case where a user has failed to log in to a Management Controller from CIM. Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 134 This message is for the use case where a user has been logged off of a Management Controller. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Remote Login ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 135 SNMP Trap ID: 30 CIM Prefix: IMM CIM ID: 0158 User Action: Information only; no action is required • FQXSPSE4034I: User [arg1] has removed a certificate. User removed certificate Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0164 User Action:...
  • Page 136 Automatically notify Support: No Alert Category: System - Remote Login SNMP Trap ID: 30 CIM Prefix: IMM CIM ID: 0230 User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 137 Information only; no action is required • FQXSPSE4042I: The third-party password function [arg1] by user [arg2] from [arg3] at IP address [arg4]. This message is for the use case where a user successfully switch the third-party password function. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other...
  • Page 138 Alert Category: none SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0248 User Action: Information only; no action is required ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 139 • FQXSPSE4050I: [arg1] sent IPMI command from [arg2], raw data: [arg3][arg4][arg5]. This message is for the use case where IPMI command to be sent. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0251 User Action: Information only;...
  • Page 140 • FQXSPSE4058I: User [arg1] removed by user [arg2] from [arg3] at IP address [arg4]. A user account was deleted by user ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 141 Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0266 User Action: Information only; no action is required • FQXSPSE4059I: User [arg1] password modified by user [arg2] from [arg3] at IP address [arg4]. A user account was changed by user Severity: Info Serviceable: No...
  • Page 142 • FQXSPSS4001I: Server General Settings set by user [arg1]: Name=[arg2], Contact=[arg3], Location=[arg4], Room=[arg5], RackID=[arg6], Rack U-position=[arg7], Address=[arg8]. A user configured the Location setting Severity: Info ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 143 Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0080 User Action: Information only; no action is required • FQXSPSS4002I: License key for [arg1] added by user [arg2]. A user installs License Key Severity: Info Serviceable: No Automatically notify Support: No...
  • Page 144 Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0226 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 145 User Action: Information only; no action is required • FQXSPSS4010I: Test Audit Log generated by user [arg1]. This message is for the use case where OS Crash Video Capture Failed. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: none SNMP Trap ID: 22 CIM Prefix: IMM CIM ID: 0237 User Action:...
  • Page 146 Automatically notify Support: No Alert Category: Warning - Other SNMP Trap ID: 60 CIM Prefix: PLAT CIM ID: 0520 User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 147 Please check event log of xClarity Controller to investigate the identified device for enhancement. • FQXSPUN0019M: Sensor [SensorElementName] has transitioned to critical from a less severe state. This message is for the use case when an implementation has detected a Sensor transitioned to critical from less severe.
  • Page 148 1. Check the Lenovo support site for an applicable service bulletin or firmware update that applies to this error. 2. Reboot the system. 3. If problem persists, collect Service Data log and Contact Lenovo Support. 4. For 1-2 Processor system: a.
  • Page 149 CIM Prefix: PLAT CIM ID: 0530 User Action: Complete the following steps: 1. Check the Lenovo support site for an applicable service bulletin or firmware update that applies to this error. 2. Reboot the system. 3. If problem persists, collect Service Data log and Contact Lenovo Support.
  • Page 150 This message is for the use case when an implementation has detected that a Sensor has deasserted a transition to non-critical from normal. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: Warning - Other ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 151 SNMP Trap ID: 60 CIM Prefix: PLAT CIM ID: 0521 User Action: Information only; no action is required • FQXSPUN2019I: Sensor [SensorElementName] has transitioned to a less severe state from critical. This message is for the use case when an implementation has detected a Sensor transition to less severe from critical.
  • Page 152 Automatically notify Support: No Alert Category: none SNMP Trap ID: CIM Prefix: IMM CIM ID: 0035 User Action: Information only; no action is required ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 153 • FQXSPUP4002I: Flash of [arg1] from [arg2] failed for user [arg3]. This message is for the use case where a user has not flashed the firmware component from the interface and IP address due to a failure. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - other SNMP Trap ID: 22...
  • Page 154 Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: CIM Prefix: PLAT CIM ID: 0372 User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 155 Information only; no action is required • FQXSPWD0003I: Power cycle of system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName]. This message is for the use case when an implementation has detected a Power Cycle by Watchdog occurred. Severity: Info Serviceable: No Automatically notify Support: No Alert Category: System - Other SNMP Trap ID: CIM Prefix: PLAT CIM ID: 0374...
  • Page 156 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 157: Chapter 4. Uefi Events

    UEFI error messages can be generated when the server starts up (POST) or while the server is running. UEFI error messages are logged in the Lenovo XClarity Controller event log in the server. For each event code, the following fields are displayed: Event identifier An identifier that uniquely identifies an event.
  • Page 158 Host Admin password has been cleared. Informational FQXSFPU4084I Host boot order has been changed. Informational FQXSFPU4085I Host WOL boot order has been changed. Informational ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 159 Table 3. Events organized by severity (continued) Message String Severity Event ID FQXSFSM0007I The XCC System Event log (SEL) is full. Informational FQXSFSR0002I [arg1] GPT corruption recovered, DiskGUID: [arg2] Informational FQXSFDD0001G DRIVER HEALTH PROTOCOL: Missing Configuration. Requires Warning Change Settings From F1. Warning FQXSFDD0002M DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller.
  • Page 160 System TPM_TCM_POLICY does not match the planar. Warning FQXSFPU4054G TPM/TCM card logical binding has failed. Warning FQXSFPW0001L CMOS has been cleared. Warning ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 161 Table 3. Events organized by severity (continued) Message String Severity Event ID FQXSFSM0002N Boot Permission denied by Management Module: System Halted. Warning Warning FQXSFSM0003N Timed Out waiting on boot permission from Management Module: System Halted. FQXSFSM0004M An XCC communication failure has occurred. Warning FQXSFSR0001M [arg1] GPT corruption detected, DiskGUID: [arg2]...
  • Page 162 A processor model mismatch has been detected for one or more Error processors. FQXSFPU0014N A processor family mismatch has been detected for one or more Error processors. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 163: List Of Uefi Events

    2. Search for the driver menu from System Settings and change settings appropriately. 3. Save settings and restart the system. 4. If the problem persists, collect Service Data logs. 5. Contact Lenovo Support. • FQXSFDD0002M: DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller. Severity: Warning...
  • Page 164 4. Contact Lenovo Support. • FQXSFDD0007G: Security Key Lifecycle Manager (SKLM) IPMI Error. Severity: Warning User Action: Complete the following steps: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 165 1. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to this error. 2. A/C cycle the system. 3. If the problem persists, collect Service Data logs. 4. Contact Lenovo Support. • FQXSFDD0012I: SATA Hard Drive Error: [arg1] was recovered.
  • Page 166 1. Check Lenovo support site for an applicable service bulletin or firmware update for the system or adapter that applies to this error. 2. If the problem persists, collect Service Data logs. 3. Contact Lenovo Support. • FQXSFIO0008M: An intra-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].
  • Page 167 1. If this PCIe device and/or any attached cables were recently installed, moved, serviced or upgraded, reseat adapter and any attached cables. 2. Check Lenovo support site for any applicable service bulletin or UEFI or adapter firmware update that applies to this error.(NOTE: It may be necessary to disable unused option ROMs from UEFI F1...
  • Page 168 Reseat adapter and any attached cables. 2. Move adapter to a different system slot, if available. 3. Check Lenovo support site for any applicable service bulletin or UEFI or adapter firmware update that applies to this error. Note: It may be necessary to configure slot to Gen1 or to use special utility software so that adapter firmware can be upgraded.
  • Page 169 1. Check the log for a separate error related to an associated PCIe device and resolve that error. 2. Check the Lenovo support site for an applicable service bulletin or firmware update for the system or adapter that applies to this error.
  • Page 170 1. Check the log for a separate error related to an associated PCIe device or NVME disk and resolve that error. 2. Check the Lenovo support site for an applicable service bulletin or firmware update for the system or adapter that applies to this error.
  • Page 171 1. Reseat the affected DIMM (Note: The event Log might contain a recent FQXSFMA0011I event denoting detected change in DIMM population that could be related to this problem.) 2. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this memory error.
  • Page 172 5. After you install qualified memory and power up the server, check to ensure this informational event is not logged again. • FQXSFMA0008I: DIMM [arg1] POST memory test failure has been recovered. [arg2] Severity: Info ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 173 3. If the DIMMs have been upgraded just prior to the issue than update uEFI to the latest version. 4. If the problem persists, collect Service Data logs. 5. Contact Lenovo Support. • FQXSFMA0009I: Invalid memory configuration for Mirror Mode has been recovered. [arg1]...
  • Page 174 1. Reseat affected DIMM (Note: The event Log might contain a recent FQXSFMA0011I event denoting detected change in DIMM population that could be related to this problem.) 2. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this memory error.
  • Page 175 DIMM connector on that memory channel. 2. If no problem is observed on the BBU connectors or the problem persists, Check the Lenovo support site for an applicable service bulletin or firmware update that applies to this memory error.
  • Page 176 3. Update UEFI firmware to the latest version. 4. If the problem persists, collect Service Data logs. 5. Contact Lenovo Support. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 177 3. If the problem persists, collect Service Data logs. 4. Contact Lenovo Support. • FQXSFMA0028M: DIMM [arg1] Self-healing, attempt post package repair (PPR) exceeded DIMM level threshold [arg2] at Rank [arg3] Sub Rank [arg4] Bank [arg5] Row [arg6] on Device [arg7].
  • Page 178 4. Move all DCPMMs of error message FQXSFMA0034M logs to the correct location. 5. If the problem persists, collect Service Data logs. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 179 3. This error message will provide the UID of the missing DCPMM, 4. Use Lenovo Service Client or contact Lenovo Support to parse log to get correct location for DCPMM Find the missing DCPMM and install it in the correct location.
  • Page 180 4. If the issue is not resolved then contact Lenovo Support. • FQXSFMA0040K: Invalid Intel Optane DCPMM configuration detected. Please verify DCPMM configuration is valid. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 181 Severity: Error User Action: Complete the following steps: 1. Check Lenovo support site for a firmware update required for this processor and install that update, if applicable. 2. If the problem persists, collect Service Data logs. 3. Contact Lenovo Support.
  • Page 182 1. Verify that the Processor is a valid option that is listed as a Server Proven device for this system. If a non-supported processor is identified, remove that Processor or replace with a supported Processor. 2. Check Lenovo support site for a firmware update required for this Processor and install that update, if applicable.
  • Page 183 1. Verify that matching processors are installed in the correct processor sockets. Correct any mismatch issues found. 2. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this processor error. 3. If the problem persists, collect Service Data logs.
  • Page 184 1. Verify that matching processors are installed in the correct processor sockets. Correct any mismatch found. 2. Check the Lenovo support site for an applicable service bulletin or firmware update that applies to this processor error. 3. If the problem persists, collect Service Data logs.
  • Page 185 1. Verify that matching processors are installed in the correct processor sockets. Correct any mismatch found. 2. Check the Lenovo support site for an applicable service bulletin or firmware update that applies to this processor error. 3. If the problem persists, collect Service Data logs.
  • Page 186 Severity: Error User Action: Complete the following steps: 1. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to this error. 2. Reboot the system. 3. If the problem persists, collect Service Data logs.
  • Page 187 Severity: Error User Action: Complete the following steps: 1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this error. 2. Reflash UEFI image. 3. Undo recent system changes (settings or devices added). Verify that the system boots. Then, re- install options one at a time to locate the problem.
  • Page 188 3. Undo recent system changes (settings or devices added). Verify that the system boots. Then, re- install options one at a time to locate the problem. 4. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this error. Update UEFI firmware if applicable.
  • Page 189 1. Perform a virtual reseat or AC cycle the server. 2. If the problem returns Collect Service Data log. 3. Contact Lenovo Support. • FQXSFPU4033F: TPM Firmware recovery is in progress. Please DO NOT power off or reset system. Severity: Warning User Action: Information only;...
  • Page 190 User Action: Information only; no action is required. • FQXSFPU4051G: Undefined TPM_TCM_POLICY found Severity: Warning User Action: Complete the following steps: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 191 1. Reboot the system. 2. If the problem persists, collect Service Data logs. 3. Contact Lenovo Support. • FQXSFPU4052G: TPM_TCM_POLICY is not locked Severity: Warning User Action: Complete the following steps: 1. Reboot the system. 2. If the problem persists, collect Service Data logs.
  • Page 192 1. If the CMOS clear was user initiated this event can be safely ignored and no further action is required. 2. If the system was recently installed, moved, or serviced, make sure the battery is properly seated. 3. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this error.
  • Page 193 1. AC cycle the system. 2. Make sure XCC and UEFI FW are operating with same compatible level. 3. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this error. 4. Reflash XCC Firmware.
  • Page 194 2. Use F1 Setup to reset date and time. 3. If the problem persists, collect Service Data logs. 4. Contact Lenovo Support. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 195: Chapter 5. Xclarity Provisioning Manager Events

    Chapter 5. XClarity Provisioning Manager events The following events can be generated by the Lenovo XClarity Provisioning Manager. For each event code, the following fields are displayed: Event identifier An identifier that uniquely identifies an event. Event description The logged message string that appears for an event.
  • Page 196 Failed to read Deployment Manager Signature from USB. FQXPMCL0003K BMC communication failed: DRIVER Mount Failure. Warning Warning FQXPMCL0004K BMC communication succeeded. Volume Name MISMATCHED. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 197 Table 4. Events organized by severity (continued) Message String Severity Event ID FQXPMCL0005K Current System Boot Mode is Legacy. OS Clone only support UEFI Warning Mode. FQXPMCL0006K Failed to export raid config. Warning FQXPMCL0007K Failed to import raid config. Warning FQXPMCL0008K Failed to export uefi settings.

  • Page 198: List Of Xclarity Provisioning Manager Events

    Error List of XClarity Provisioning Manager events This section lists all messages that can be sent from the Lenovo XClarity Provisioning Manager. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 199 • FQXPMCL0001K: Bootx64.efi is not found. Failed to Boot OS. Severity: Warning User Action: 1. Restart BMC via supported method and reboot the system. 2. If the problem persists, reflash BMC firmware. 3. Reboot system and retry OS booting. 4. Perform AC reset or virtual reseat. Note: When performing AC reset, after powering off AC, wait several seconds before powering on AC.
  • Page 200 Severity: Info User Action: Information only; no action is required. • FQXPMCL0007K: Failed to import raid config. Severity: Warning User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 201 1. Check the following Lenovo support site for information on supported RAID adapters. http://www. lenovo.com/us/en/serverproven/index.shtml 2. Ensure RAID adapter, LXPM, and UEFI firmware are at the latest levels. 3. Ensure the state of RAID adapter and disk drives are healthy.
  • Page 202 User Action: Information only; no action is required. • FQXPMEM0003I: LXPM has exited. Control returned to UEFI Severity: Info User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 203 Information only; no action is required. • FQXPMEM0004I: Launching diagnostic program Severity: Info User Action: Information only; no action is required. • FQXPMEM0005I: boot diagnostic program success Severity: Info User Action: Information only; no action is required. • FQXPMEM0006M: Unable to locate diagnostic firmware image Severity: Error User Action: 1.
  • Page 204 2. Restart BMC via supported method and reboot the system. 3. If the problem persists, reflash BMC firmware. 4. Retry OS deployment. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 205 5. If the problem persists, perform AC reset or virtual reseat. Note: When performing AC reset, after powering off AC, wait several seconds before powering on AC. After AC power is restored, power on the host system. 6. If the problem persists, contact technical support. •...
  • Page 206 1. Change boot mode to UEFI mode 2. Retry OS deployment. • FQXPMOS0010I: Red Hat RHEL 7.3 (64-bit) OS installed Severity: Info User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 207 Information only; no action is required. • FQXPMOS0011I: Red Hat RHEL 6.9 (64-bit) OS installed Severity: Info User Action: Information only; no action is required. • FQXPMOS0012I: SLES 12 for AMD64 and Intel64 Service Pack 2 OS installed Severity: Info User Action: Information only;...
  • Page 208 Severity: Info User Action: Information only; no action is required. • FQXPMOS0027I: Vmware ESXi 6.0 U3 OS installed Severity: Info User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 209 Information only; no action is required. • FQXPMRS0011K: Failed to change disk drives' state. Severity: Warning User Action: 1. Ensure LXPM and RAID adapter firmware are at the latest levels. 2. Ensure the state of the RAID adapter and disk drives are both healty. 3.
  • Page 210 3. If the problem persists, contact technical support. • FQXPMSD0009M: Device error detected when LXPM sent a test command to a hard drive. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 211 Severity: Error User Action: 1. Do one of the following: – If the affected drive(s) are detected by the system, update the disk drive firmware and reboot the server. – If the affected drive(s) are not detected by the system or failing to respond: a.
  • Page 212 User Action: Information only; no action is required. • FQXPMUP0001K: The system configuration does not meet the prerequisite Severity: Warning User Action: ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 213 1. Follow prompts to update the firmware and retry the update. 2. If the problem persists, contact technical support. • FQXPMUP0002K: The selected packages are not compatible Severity: Warning User Action: 1. Follow prompts to update each individual firmware package. 2.
  • Page 214 • FQXPMUP0103I: Start to update linux driver Severity: Info User Action: Information only; no action is required. • FQXPMUP0104I: Start to update UEFI ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 215 Note: When performing AC reset, after powering off AC, wait several seconds before powering on AC. After AC power is restored, power on the host system. 4. If the problem persists, try a different Lenovo tool to perform the update (eg. XClarity Administrator, XClarity Controller, or XClarity Essential OneCLI).
  • Page 216 Note: When performing AC reset, after powering off AC, wait several seconds before powering on AC. After AC power is restored, power on the host system. 4. If the problem persists, try a different Lenovo tool to perform the update (eg. XClarity Administrator, XClarity Controller, or XClarity Essential OneCLI).
  • Page 217 Note: When performing AC reset, after powering off AC, wait several seconds before powering on AC. After AC power is restored, power on the host system. 4. If the problem persists, try a different Lenovo tool to perform the update (eg. XClarity Administrator, XClarity Controller, or XClarity Essential OneCLI).
  • Page 218 1. Press "Apply" button on VPD update page. 2. Reboot the system if step 1 failed. 3. If the problem persists, contact technical support. ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 219: Appendix A. Getting Help And Technical Assistance

    Appendix A. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. On the World Wide Web, up-to-date information about Lenovo systems, optional devices, services, and support are available at: http://datacentersupport.lenovo.com...

  • Page 220: Collecting Service Data

    Collecting service data To clearly identify the root cause of a solution issue or at the request of Lenovo Support, you might need collect service data that can be used for further analysis. Service data includes information such as event logs and hardware inventory.

  • Page 221: Contacting Support

    • Lenovo XClarity Essentials OneCLI Lenovo XClarity Essentials OneCLI has inventory application to collect service data. It can run both in- band and out-of-band. When running in-band within the host operating system on the solution, OneCLI can collect information about the operating system, such as the operating system event log, in addition to the hardware service data.
  • Page 222 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...

  • Page 223: Index

    Index hardware service and support telephone numbers collecting service data help creating a personalized support web page custom support web page Lenovo XClarity Controller error messages Lenovo XClarity Controller events error codes and messages Lenovo XClarity Controller UEFI 153, 191...
  • Page 224 ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node Messages and Codes Reference...
  • Page 226 Part Number: SP47A24248 Printed in China (1P) P/N: SP47A24248 *1PSP47A24248*...

This manual is also suitable for:

7x207x217x22

Table of Contents