Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEC CDR-3001A
Summary of Contents for NEC CDR-3001A
- Page 1 Internal CD-ROM Reader CDR-3001 User's Manual ECDR3001.PM5 98.11.20, 3:01 PM...
- Page 2 Laser Safety Information This drive employs a laser. Do not remove the cover or attempt to service this device when connected due to the possibility of eye damage. CAUTION Use of control of adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
- Page 3 NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
Page 4: Warning
HEED THE FOLLOWING Read the operating instructions carefully before using the unit and be sure to use it properly. After reading the instructions, store them in an easily accessible place so they can be consulted whenever necessary. WARNING • Continued use should there be an irregularity (smoke, abnormal smell or sound, etc.) will lead to fires or electric shocks. -
Page 5: Caution
CAUTION • When connecting computer equipment, audio equipment, speakers, etc., be sure to read the respective manuals carefully, turn of the power, and follow the connection instructions. Using cords other than the specified cords or extending cords could generate heat and result in burns, etc. •... -
Page 6: Cautions
Cautions Cleaning To clean the CD-ROM reader, wipe it with a soft, damp cloth, using mild detergent if necessary. Please avoid using solvents such as benzine or paint thinner. This can cause color changes or deformation of the CD- ROM reader. Handling the Disc •... -
Page 7: Table Of Contents
Table of Contents Heed the following Warning ................3 Caution ................4 Cautions Cleaning ................5 Handling the Disc ............... 5 Part Names and Functions Front View ................7 Rear View ................8 Installation Jumper Setting ..............9 Installing the CD-ROM reader in a host PC ....... 10 Inserting/Removing a CD Using the CD-ROM Drive Installed Vertically .... -
Page 8: Part Names And Functions
Part Names and Functions Front View 1 Phones Jack This jack is used to connect a set of headphones. Please use headphones with a stereo mini-jack plug. 2 Volume Control This control is used to adjust the headphone volume. NOTE: This control has no effect on the audio output from the LINE OUT connector on the back of the CD-ROM reader. -
Page 9: Rear View
Rear View 7 Jumper Blocks These blocks of jumper locations set the configuration for the CD- ROM reader. (See page 9, “Jumper Setting” for details.) 8 DIGITAL OUT Connector This connector is used to connect Digital Audio to an audio board. 9 Line Out Connector This connector is used to connect CD-Audio to an audio board. -
Page 10: Installation
Installation Jumper Setting A jumper consists of a pair of pins and a connector which fits over the pins. When the connector is in place it establishes an electronic link between the pins, which enables the function being controlled by the jumper. -
Page 11: Installing The Cd-Rom Reader In A Host Pc
Installing the CD-ROM reader in a host PC Note Refer to the guidebook included with your personal computer for instruc- tions on installing the CD-ROM reader. This chapter gives one example of installation. 1. Attach the mounting rails to both the left and right sides of the CD- ROM reader. - Page 12 5. Locate a spare power cable in your computer. 6. Connect that power cable to the power connector on the back of the CD-ROM reader. CD-ROM READER POWER CONNECTOR POWER CABLE ECDR3001.PM5 98.11.20, 3:01 PM...
- Page 13 7. Connect the I/O BUS connector on the CD-ROM reader and the IDE connector. Connect the colored stripe side of the cable to the side marked with the arrow ( I/O BUS CONNECTOR BUS CABLE ARROW COLORED STRIPE (Pin 1) 8.
-
Page 14: Inserting/Removing A Cd
Inserting/Removing a CD Using the CD-ROM Reader Installed Vertically When using the CD-ROM reader, in the vertical position, load and unload discs as shown on the diagram below. CD-ROM reader installed vertically CD-ROM reader installed vertically (right side) (left side) Caution Only 12cm discs can be used when the CD-ROM reader is installed vertically. -
Page 15: Inserting A Cd
Inserting a CD 1. Press the Load/Eject button. The CD tray will be ejected. 2. Place the disc in the center of the tray with the label side facing up. 3. Press the Load/Eject button. The CD tray will be retracted. Removing a CD 1. -
Page 16: Specifications
Specifications CD-ROM Section User Data Capacity ......656M bytes/disc (Mode 1) 748M bytes/disc (Mode 2) Total Number of Blocks ....336K blocks/disc (Maximum) User Data Blocks ......2048 bytes/block (Mode 1 and Mode 2, Form 1) 2336 bytes/block (Mode 2) 2328 bytes/block (Mode 2 Form 2) Data Transfer Rate ......