free stats
Download Print this page
Sealey 10000LQ Instructions

Sealey 10000LQ Instructions

10 ton long reach super rocket lift trolley jack

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS JACK CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1. SAFETY PRECAUTIONS
 Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
 Locate the jack in a suitable, well lit work area.
 Keep work area clean and tidy and free from unrelated materials.
 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
 Place wedges under wheels of vehicle (but ensure wheels of jack can move freely).
 Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in 1st or reverse gear ("PARK" if automatic).
 Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
 Ensure there are no passengers in the vehicle.
 Ensure all non-essential persons keep a safe distance whilst the jack is in use.
 Only place jack under those lifting points recommended by vehicle manufacturer (see vehicle handbook).
 Check the lifting point is stable and centred on the jack saddle.
 Ensure the jack wheels are free to move and that there are no obstructions.
 DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
 Use suitable capacity axle stands under the vehicle before proceeding with any task.
 Ensure there are no persons or obstructions beneath the vehicle before lowering.
 Use a qualified person to maintain or repair the jack hydraulic system.
 DO NOT operate the jack if damaged.
 DO NOT allow untrained persons to operate the jack.
 DO NOT exceed the rated capacity of the jack.
 DO NOT allow the vehicle to move while supported by the jack, nor use the jack to move the vehicle.
 DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substance.
 DO NOT work under the vehicle until axle stands have been correctly positioned.
 DO NOT use the jack for purposes other than that for which it is designed.
 DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.
 DO NOT adjust the safety overload valve.
 When not in use store jack, fully lowered, in a safe, dry, childproof area.
2.
SPECIFICATIONS
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10000kg
Max. Saddle Height . . . . . . . . . . . . . . . . . . . . . 686mm
Min. Saddle Height . . . . . . . . . . . . . . . . . . . . . 175mm
Long reach design for easier access to deep-set jacking points.
Single-piece hydraulic unit with hand or foot operation.
Single-piece handle lockable in three positions for storage and improved manoeuvrability.
Rocket lift feature brings lifting arm into contact with jacking point with five or less strokes of the handle/foot pedal.
Integral saddle pad provides protection for the jacking point.
Heavy-duty swivel castor wheels and Ø130mm x 55mm wide front wheels for even load distribution.
Grease nipples simplify maintenance.
3.
ASSEMBLY & PURGING
3.1.
Fit the handle assembly into the handle socket (fig. 1.1) and the locking control lever (fig. 2.3.) into the
guide (fig. 1.2.) Tighten the handle set bolt (fig. 1.3.).
3.2.
Oil the mechanical parts before first use - and regularly thereafter.
3.3.
Before using for the first time purge any air from the hydraulic system as follows. Open the release
valve (fig. 2.1.), by turning anticlockwise, pump handle twenty to thirty times and close the release
valve.
4. OPERATING INSTRUCTIONS
4.1.
General jacking
 WARNING! Before lifting, ensure Section 1 safety instructions are strictly followed.
4.1.1.
Prepare vehicle as described in safety instructions ensuring the ground on which jack is to stand is
level and solid (not tarmacadam).
4.1.2.
Position the jack saddle under the vehicle manufacturer's recommended lifting point (see vehicle
handbook). To aid moving the jack the pump handle may be locked in any one of three positions
using the locking control lever.
4.2.
Jacking the vehicle
4.2.1.
The jack saddle (fig. 2.4.) may be raised up to the load by using the foot pedal (fig. 2.5.) or jacking handle. DO NOT attempt to
raise the load with the foot pedal.
4.2.2.
Ensure the release valve is closed. Commence pumping the handle up and down using maximum strokes until the vehicle reaches
the required height.
Note:
If the jack becomes overloaded, the safety valve will operate and prevent the jack from lifting further.
INSTRUCTIONS FOR:
10 TON LONG REACH SUPER ROCKET LIFT TROLLEY JACK
10000LQ
MODEL No:
Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1309mm
Max. Chassis Height. . . . . . . . . . . . . . . . . . . . . . 252mm
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140kg
Original Language Version
Fig. 1.
Fig. 2.
10000LQ
Issue: 3 - 31/03/10

Advertisement

loading

Summary of Contents for Sealey 10000LQ

  • Page 1 10000LQ MODEL No: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
  • Page 2 2) Remove cover plate (fig. 2.2.) and then the filler plug, taking care that no dirt is allowed into the tank. 3) Check that level is to the bottom of the filler plug (fig. 3.). Add oil if necessary. NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL. ...
  • Page 3 DESCRIPTION 1....10000LQ-01 ... HYDRAULIC POWER UNIT 2....10000LQ-02 ... FRONT WHEEL ASSEMBLY 3..