Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear protective
instructions
gloves
1. SAFETY
‰
WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions
and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
WARNING! Ensure all preliminary checks are carefully carried out before use and that all fixings are correctly and securely engaged.
‰
Immediately repair or replace damaged parts (use authorised service agent). Ensure use of genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Use jack on level and solid ground, preferably smooth concrete. Ensure the floor over which the loaded jack will be
‰
transported is swept clean.
WARNING! Ensure that the loaded item is correctly supported, well balanced and secured in place prior to final removal from vehicle
‰
and before any movement of the loaded jack within the workshop.
DO NOT make any modifications to the unit supplied.
8
▲
DANGER! DO NOT use on tarmacadam, or any other soft surface as jack may sink or topple. Serious injury may result if ignored.
▲
DANGER! If the load tips or leans, stop what your are doing. MOVE QUICKLY TO A SAFE DISTANCE. DO NOT TRY TO HOLD
OR STEADY JACK.
9
The unit is intended for use only with Sealey products 500TTJ and 800TTJ.
Ensure that load adaptor is correctly attached to the jack and that the grub-screw is fitted before use.
9
2. INTRODUCTION
Fully adjustable SFC01 Subframe/Engine support adaptor that is supplied with various designs of fittings to suit different applications.
Designed to assist in the removal and fitting of subframes, complete engine assemblies, rear axles, gearboxes, fuel tanks, exhaust systems
and other awkward loads. The adaptor easily fits directly on to the Sealey 500TTJ and 800TTJ Transmission Jacks and assists in allowing
awkward two or three man jobs to be carried out by one person.
3. SPECIFICATION
Model No.:.................................................................. SFC01
Capacity ....................................................................... 450kg
4. ASSEMBLY
4.1.
Thread the boss located on the underside of
the Load Plate onto the Jack ram. Fix in place
using the grub screw supplied when fully
engaged.
Thread M16 Stud and Hex nut (fig.1) into load
4.2.
plate such that underside of the nut rests
on the surface of the Load Plate and that the
stud is flush with the nut.
4.3.
Slide the Support arm guide over the stud and
screw the Support arm hand wheel onto it.
4.4.
Screw the Tool post and hand wheel assembly
into the Support arm.
© Jack Sealey Limited
SUBFRAME/ENGINE LOAD ADAPTOR FOR
TTJ TRANSMISSION JACKS
SFC01
MODEL NO:
Wear safety
footwear
Tool post and
Hand wheel
fig.1
Original Language Version
Support arm
Hand wheel
SFC01
M16 Stud bar
and Hex. nut
Load Plate
Support arm
Guide
Issue 1
12/01/22
Advertisement
Related Manuals for Sealey SFC01
Summary of Contents for Sealey SFC01
- Page 1 Designed to assist in the removal and fitting of subframes, complete engine assemblies, rear axles, gearboxes, fuel tanks, exhaust systems and other awkward loads. The adaptor easily fits directly on to the Sealey 500TTJ and 800TTJ Transmission Jacks and assists in allowing awkward two or three man jobs to be carried out by one person.
- Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...