Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. SAFETY
Modern vehicles contain extensive electronic systems.
You are required to check with the vehicle Manufacturer, for any specific instructions regarding the use of this type of
equipment on each vehicle. No liability will be accepted for damage / injury, where this product is not used in accordance
with all instructions.
9
Ensure that the vehicle is in a well ventilated area.
9
Apply the handbrake and select neutral or 'park' before attempting to start.
9
Ensure that the ignition switch and all ancillary electrical equipment is switched off.
9
Keep clear of any pulleys, belts etc. that will move once the engine starts.
9
Take care to ensure correct connection polarity; red clamp to positive, black clamp to negative.
9
Energise the unit only at ambient temperatures between -30°C and 40°C.
9
When not in use, switch off and store in a cool, dry place out of the reach of children.
8
DO NOT allow this power pack to become wet.
8
DO NOT dismantle this unit: there are no user serviceable parts inside.
8
DO NOT use in explosive atmospheres (e.g. the presence of flammable liquids, gases or dust).
8
DO NOT use the unit if it appears damaged in any way.
8
DO NOT use this product for any purpose other than that for which it is designed.
8
DO NOT leave in direct sunlight or expose to heat.
8
DO NOT use abrasive or solvent cleaners on this product.
8
DO NOT allow children to play with this product
8
DO NOT allow the positive and negative clamps to touch.
1.1.
BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
‰
8
DO NOT attempt to open, disassemble, modify or service the battery pack.
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
8
8
DO NOT expose to temperatures above 60°C (140°).
9
Replace only with the battery pack designated for this product.
9
Recycle or dispose of used battery as stipulated by local regulation.
8
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
2. INTRODUCTION
Easily fits in a glove box or backpack and benefits from being compact and lightweight. Powered by Lithium-ion technology and fully
protected against short circuit, overload and reverse polarity. Fitted with a 16,000mAh Lithium-ion battery and two USB Type A outlets (5V/3A,
9V/2A,12V/1.5A), Type C input & output leads (5V/3A,9V/3A,12V/2.5A,20V/1.5A), this unit can also supply several full charges for smartphones
and tablets/laptops. Capable of starting an average 8ltr petrol or 6ltr diesel engine. Integral LED flashlight. Waterproof to IP67 rating. Supplied in
a sturdy hard-shell zip up case.
3. SPECIFICATION
Model no: .................................................................. RS1200
Auxiliary Output:.....................................................................
................................USB (x2) both - 5V/3A, 9V/2A, 12V/1.5A
............................. Type C - 5V/3A,9V/3A,12V/2.5A,20V/1.5A
Cable & Clamp Length: .............................................. 385mm
Capacity: .................................16Ah @ 3.7V or 4Ah @ 14.8V
Maximum Current: ....................1200A Peak, 600A Cranking.
Maximum Starting Capacity: .................... 8L Petrol/6L Diesel
Size (W x D x H): ......................................100 x 45 x 185mm
Voltage: ............................................................................12V
© Jack Sealey Limited
ROADSTART® 1200A 12V LITHIUM-ION JUMP
STARTER POWER PACK
MODEL NO:
Wear protective
Warning:
gloves
Electricity
Original Language Version
RS1200
RS1200
Issue:1
06/06/22
Advertisement
Related Manuals for Sealey ROADSTART RS1200
Summary of Contents for Sealey ROADSTART RS1200
- Page 1 RS1200 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 After use and before performing cleaning, unplug and disconnect the unit. 6.2. Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery clamps, cords, and the outer case. Original Language Version © Jack Sealey Limited RS1200 Issue:1 06/06/22...
- Page 3 BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.