Advertisement
Quick Links
This product is intended for use with UL
Listed products and must be installed by a
R
qualified professional installer.
Read instruction sheet before you start installation and assembly.
• Installer must verify that the ceiling will safely support four times the combined weight of all attached equipment and
hardware.
NOTE: Accessories listed in the included sheet, as well as other parts, can be ordered
through Peerless by calling 1-800-729-0307 or visiting www.peerlessindustries.com.
Turn to the appropriate page for your ceiling installation.
Installations:
To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings ............................................................................ step 2, page 3
To Concrete Ceilings ........................................................................................................................ step 3, page 4
Applications:
Threaded Rod .................................................................................................................................. step 4, page 5
Extension Column ............................................................................................................................ step 5, page 5
Projector Alignment:
Adjusting Roll, Pitch, and Yaw ...................................................................................................... step 12, page 8
Visit the Peerless Web Site at www.peerlessmounts.com
Installation and Assembly - All-in-One Projector Mount
for NEC
Maximum Load Capacity: 25 lb (11 kg)
WARNING
1 of 8
™
Projectors
ISSUED: 11-16-05 SHEET #: 055-9447-2
For customer care call 1-800-729-0307 or 708-865-8870.
Model:
VL80CM
Advertisement
Related Manuals for NEC VL80CM
Summary of Contents for NEC VL80CM
- Page 1 Threaded Rod ... step 4, page 5 Extension Column ... step 5, page 5 Projector Alignment: Adjusting Roll, Pitch, and Yaw ... step 12, page 8 Visit the Peerless Web Site at www.peerlessmounts.com for NEC ™ Projectors Maximum Load Capacity: 25 lb (11 kg) WARNING 1 of 8 For customer care call 1-800-729-0307 or 708-865-8870.
-
Page 2: Parts List
Before you start check the parts list to insure all of the parts shown are included. Parts List Description A projector mount assembly B 4 mm security allen wrench C #10-32 x 3/8" serrated washer head socket pin screw D #10-32 x 1/4" socket pin screw E 1/4"... - Page 3 Disengage connection block from projector mount assembly (A) by unscrewing captive screw and sliding out connection block as shown. CAPTIVE SCREW Installation To Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) with two #14 x 2.5"...
-
Page 4: Installation To Concrete Ceilings
Installation to Concrete Ceilings Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) using two concrete anchors (G), two flat washers (E), and two #14 x 2.5" wood screws (F) as shown in Illustration A and 1, 2, and 3 (below). -
Page 5: Installation To Extension Column
Installation to Threaded Rod Attach projector mount assembly (A) to two 3/8-16 threaded rods (not included) using two 3/8-16 hex thin nylon- insert locknuts (not included) as shown in figure 1.1 or figure 1.2. Skip to step 6. 3/8 -16 THREADED ROD (NOT INCLUDED) 3/8 -16 HEX THIN NYLON-INSERT... - Page 6 Note: The projector you are installing may differ in appearance from the sample illustrated below. Align shoulder on connection block opposite notch in adapter plate. Attach adapter plate (H) to connection block from projector mount assembly (A) using two #10-32 x 3/8" serrated washer head socket pin screws (C) as shown. NOTCH INDICATES FRONT OF PROJECTOR Flip projector upside down.
- Page 7 OPTIONAL: Press cable clip (O) into hole on adapter plate (H) indicated below. Pull on cable clip (O) to make sure it is engaged. Use cable tie (P) with cable clip (O) for cord management. Find your projector from the models listed below. Fasten M4 x 25 mm thumb screw (L) and .313 x .198 x .688H retaining spacer (K) to adapter plate (H) at hole indicated on the corresponding hole pattern diagram.
- Page 8 WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the projector. Slide connection block with projector into projector mount assembly (A) as shown. Tighten captive screw to secure projector to projector mount assembly (A).