Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Do not cover Indoor use only
instruction
manual
1. SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the heater is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
1.1.
ELECTRICAL SAFETY INFORMATION. It is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply off and remove from use.
9
Ensure that repairs are carried out by a qualified electrician.
9
Replace a damaged plug with a BS1363/A 3 pin plug. If in doubt contact a qualified electrician.
9
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
9
Sealey recommend that repairs are carried out by a qualified electrician.
9
1.2.
GENERAL SAFETY
WARNING! Disconnect the heater from the mains power supply before carrying out any servicing or
‰
maintenance.
Disconnect the heater from the power supply before handling or cleaning.
9
Maintain the heater in good order and clean condition for best and safest performance.
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Ensure there is adequate lighting and keep the immediate area in front of the outlet grille clear.
9
Only use the heater standing on its feet in the upright position.
9
DO NOT allow any untrained persons to use the heater. Ensure they are familiar with the controls and hazards of the heater.
8
DO NOT let power lead hang over an edge (i.e. table), or touch a hot surface, lie in heater hot air flow, or run under a carpet.
8
DO NOT touch the outlet grille (top) of the heater during and immediately after use as it will be hot.
8
DO NOT place the heater near items that may be damaged by heat.
8
DO NOT place heater too close to yourself or any object, allow the air to circulate freely.
8
DO NOT use the heater for any purpose other than for which it is designed.
8
DO NOT use heater on very deep pile carpets.
8
DO NOT use the heater outdoors. These heaters are designed for indoor use only.
8
DO NOT use heater if the power cord, plug or the heater is damaged, or if the heater has become wet.
8
DO NOT use in bathroom, shower room, or in any wet or damp environments or where there is high condensation.
8
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT allow the heater to get wet as this may result in an electric shock and personal injury.
8
DO NOT insert or allow objects to enter any openings of heater as this may cause an electric shock,a fire or damage to heater.
8
DO NOT use the heater where there are flammable liquids, solids or gases such as petrol, solvents, aerosols etc, or where heat sensitive
8
materials may be stored.
DO NOT place the heater immediately below any electrical outlet.
8
DO NOT cover heater when in use, and do not obstruct the air inlet and outlet grille (i.e. clothing, curtain, furniture, bedding etc).
8
Allow the unit to cool before storage. When not in use, disconnect from the mains power supply and store in a safe, cool, dry, childproof area.
9
© Jack Sealey Limited
2000W CONVECTOR HEATER
CD2013.V3
MODEL NO:
Original Language Version
Recommended fuse rating
13 Amp
CD2013.V3
Issue:1
31/10/22
Advertisement
Related Manuals for Sealey CD2013.V3
Summary of Contents for Sealey CD2013.V3
- Page 1 CD2013.V3 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 If the cause is not obvious return the heater to your local Sealey stockist for servicing. 6. MAINTENANCE WARNING: Before attempting any maintenance ensure the unit is unplugged from the mains power supply and that it is cool.
- Page 3 Room temperature control, with open window detection With distance control option With adaptive start control With working time limitation With black bulb sensor Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk ERP Table 2...