Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations
‰
are adhered to when using this sander
WARNING! Disconnect from the mains power and ensure that the pad is at a complete standstill before changing accessories,
9
servicing or performing any maintenance.
WARNING! Keep all holding screws in place, tight and in good working order. Check regularly for damaged parts.
9
WARNING! Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
Familiarise yourself with the application, limitations and potential hazards of the sander.
9
Maintain the sander in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
A part that is damaged must be repaired/replaced before the sander is next used.
Use the sander in a suitable work area and keep the area clean and tidy and free from unrelated materials. Ensure that there is
9
adequate lighting.
Keep the sander clean for best and safest performance.
9
Before each use check all attachments for condition. If worn or damaged replace immediately.
9
Ensure that there are no flammable materials near the work area.
9
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Avoid unintentional starting.
9
DO NOT use the sander for any purpose other than that for which it is designed.
8
DO NOT operate the sander if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT switch the sander on until the head is in contact with the panel and switch the unit off before removing the head from the panel.
8
DO NOT get the sander wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT allow untrained persons to operate the polisher.
8
DO NOT operate the sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use the sander where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT leave the sander operating unattended.
8
DO NOT carry the sander with your finger on the power switch.
8
DO NOT pull the cord from the power supply
8
Use a qualified person to maintain the sander.
9
When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
9
WARNING! LEAD PAINT
‰
Paint once contained lead as a traditional ingredient. The dust from the removal of such paint is toxic if inhaled or ingested and must,
therefore, be avoided. The following action must be taken before using the sander on a surface that you suspect may have contained
lead in the paint.
▲
DANGER! User must determine potential hazard relating to age of paint to be removed. (Modern paints do not contain lead).
Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint dust,
9
expectant women, babies and children.
We recommend personal protection by using the following safety items: a) Paint Spray Respirator b) PE Coated Hooded Coverall
9
c) Latex Gloves
Take adequate measures to contain the paint dust, flakes, and scrapings.
9
Continue to wear safety equipment as in 3 above, and thoroughly clean all areas when task is complete. Ensure that paint
9
waste is disposed of, in sealed bags or containers, according to local authority regulations.
2. INTRODUCTION
Part of the SV10.8 Series offering a one battery fits all solution, keeping costs down without compromising on
performance. Compact, lightweight cordless Detail Sander - Body Only. Comfortable housing with soft grip to help reduce vibration.
Ideal for DIY tasks such as removing rust, paint and sanding wood. Hook-and-loop pad for fast change of sandpaper. Three pieces
of sandpaper supplied. Features dust extractor port. A dust collection bag is supplied. Requires compatible 10.8V 2Ah or 4Ah
battery and mains charger, sold separately.
© Jack Sealey Limited
10.8V SV10.8 SERIES 150MM DETAIL SANDER
MODEL NO:
Wear protective
Wear safety
gloves
footwear
Original Language Version
CP108VDSBO
Wear protective
Wear ear
clothing
protection
Wear a mask
CP108VDSBO Issue 3 (3)
08/03/23
Advertisement
Related Manuals for Sealey CP108VDSBO
Summary of Contents for Sealey CP108VDSBO
- Page 1 CP108VDSBO MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Fig. 1 4. OPERATION NOTE: Battery state is indicated by the three LEDs on top (fig.1). NOTE: Excessive pressure on the machine does not result in higher working efficiency. It increases wear on the internal mechanics and can damage the polisher/sander and the item being worked. Use the relevant pad required for the job - See Sealey website for more details 4.1. The On/off switch located at top of sander unit. (fig.1) 5. MAINTENANCE WARNING! Remove battery from tool before performing any maintenance or making adjustments.