Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Warning:
instruction
Electricity
manual
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information: it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
GENERAL SAFETY
1.2.
WARNING! If a fuse blows, ensure it is replaced with a fuse of identical type and rating.
‰
WARNING! Ensure there is nobody in front of the lamp when it is switched on.
‰
Disconnect the panel dryer from the power supply before servicing, changing accessories, or performing any maintenance.
9
Ensure that the panel dryer is in good condition before use. If in any doubt do not use the unit and contact an electrician.
9
When not in use, store the panel dryer carefully in a safe, dry, childproof location.
9
Familiarise yourself with the application and limitations of the panel dryer.
9
Check that lamp guards are in place, undamaged and firmly attached.
9
Keep tools and other items away from the panel dryer when it is in use.
9
Keep the work area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the work area.
9
Remember that the lamp panel will get hot, allow to cool after use.
9
Maintain the panel dryer in good condition. Use authorised agent for servicing.
9
Keep the dryer clean, but DO NOT use solvents.
9
Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate your warranty.
9
DO NOT use this product to perform a task for which it has not been designed.
8
DO NOT use the panel dryer outdoors, or in damp, or wet locations, and DO NOT operate within the vicinity of flammable liquids, gases or
8
solids.
2. INTRODUCTION
Designed and developed to assist with any number of small drying processes. Ideal for spot repairs, engine drying, adhesive stripe
removal, drying filler, drying primer or just preheating prior to spraying. Supplied with a sturdy 1500mm plated steel stand and a 3.7m
power cable and 3-pin plug.
© Jack Sealey Limited
PANEL DRYER, INFRARED, SHORT WAVE, 2100W
IR2000S
MODEL NO:
Indoor
Warning:
Use Only
Hot Surface
Original Language Version
Do Not Cover
Replacement fuse
rating:13A
IR2000S
Issue:3
12/06/23
Advertisement
Related Manuals for Sealey IR2000S
Summary of Contents for Sealey IR2000S
- Page 1 IR2000S MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Assemble lamp arrangement using the adjustment handle, spring washer and plain washers (fig.2.C) in seven positions shown. 4.2.2. Assemble post mounting section using adjustment handle, spring washer and plain washers in position shown (fig.2.F). fig.2 Original Language Version © Jack Sealey Limited IR2000S Issue:3 12/06/23...
- Page 3 Uneven baking. The emitter is not at same height as the Adjust the emitter to allow it to be at repaired surface. height as the repaired surface. IR2000S Issue:3 12/06/23 Original Language Version © Jack Sealey Limited...
- Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk...