Page 1
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Lenovo ThinkBook 15p 20V30007IX o cerca il tuo prodotto tra le migliori offerte di Notebook Hardware Maintenance Manual Lenovo ThinkBook 15p...
This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide.
4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: •...
• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard disk drive might have been dropped or subject to excessive force. CRU list Table 1. Model: Lenovo ThinkBook 15p IMH (MT: 20V3) Type ac power adapter...
Chapter 4. Removing a FRU or CRU Service tools The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for serving the product models as described by this publication. Prepare them before you service the product.
3. Follow the correct sequence in the steps for removing an FRU, as shown in the illustrations by the numbers in square callouts. 4. When removing an FRU, move it in the direction as shown by the arrow in the illustration. 5.
Figure 4. Pry up the latches and remove the lower case Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Lower case Remove the battery pack Make sure the following FRU (or CRU) has been removed.
Remove the SSD by pulling it away from the slot. Figure 7. Remove the SSD Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Remove the Wi-Fi card Make sure the following FRU (or CRU) has been removed.
Figure 8. Remove the Wi-Fi card Screw specifications Number of screws M2 x L3 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Wi-Fi card Remove the memory module Make sure the following FRU (or CRU) has been removed.
Release the two latches on both edges of the socket at the same time. Then, remove the memory module. Figure 10. Remove the memory module Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts: Memory module...
Figure 11. Loosen seven screws and then remove the heat sink Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Heat sink Remove the fan Make sure the following FRUs (or CRUs) have been removed.
Number of screws M2 x L5 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Remove the USB board Make sure the following FRU (or CRU) have been removed. “Remove the lower case” on page 28 Step 1.
Screw specifications Number of screws M2 x L5 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: USB board Remove the power board cable Make sure the following FRUs (or CRUs) have been removed.
Remove the power board Make sure the following FRUs (or CRUs) have been removed. “Remove the lower case” on page 28 “Remove the heat sink” on page 32 Step 1. Disconnect the battery pack cable from the system board. Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable. Step 2.
Figure 19. Remove one screw and then remove the power board Screw specifications Number of screws M2 x L3 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Power board Remove the fingerprint board Make sure the following FRUs (or CRUs) have been removed.
Figure 20. Remove the fingerprint board Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Fingerprint board Remove the DC-in bracket Make sure the following FRU (or CRU) has been removed. “Remove the lower case” on page 28 Step 1.
Disconnect the speaker cable from the system board and release the speaker cable from the cable guide. Remove the speakers. Figure 22. Remove the speakers Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Speakers Remove the RTC battery Make sure the following FRUs (CRUs) have been removed.
Figure 23. Disconnect the RTC battery cable from the system board and remove the RTC battery Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: RTC battery Remove the system board, the USB board cable and the fingerprint board cable Make sure the following FRUs (or CRUs) have been removed.
Page 47
Figure 24. Disconnect cables connected to the system board and peel off the tape Step 2. Disconnect the USB board cable from the USB board and disconnect the fingerprint board cable from the fingerprint board. Figure 25. Disconnect the USB board cable from the USB board and disconnect the fingerprint board cable from the fingerprint board Step 3.
Disconnect the USB board cable and the fingerprint board cable from the system board. Figure 27. Disconnect the USB board cable and the fingerprint board cable from the system board Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts:...
Figure 28. Detach the antenna cable connectors and disconnect the EDP cable from the system board Step 3. Rotate the LCD module to an angle of more than 90 degrees and place the computer on a flat surface as shown. Remove four screws and then remove the LCD module. Figure 29.
“Remove the system board, the USB board cable and the fingerprint board cable” on page 40 “Remove the LCD module” on page 42 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Upper case (with keyboard and touchpad) Disassemble the LCD module The LCD module as a whole is not an FRU.
Figure 31. Remove the LCD bezel Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: LCD bezel Remove the hinges Make sure the following FRUs (CRUs) have been removed. “Remove the LCD module” on page 42 “Remove the strip cover”...
Note: For LCD panel with the factory color calibration feature, do the following to install new color profiles: 1. Connect your computer to the network and close the X-Rite Color Assistant program. 2. Go to https://pcsupport.lenovo.com/us/en/downloads/DS543953 to download the installation software. Double-click the EXE file and follow the on-screen instructions to finish the installation.
Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts: LCD panel Removable tape Remove the camera rubbers Make sure the following FRUs (CRUs) have been removed. “Remove the LCD module” on page 42 “Remove the strip cover” on page 44 “Remove the LCD bezel”...
Figure 36. Disconnect the EDP cable from the camera board and remove the camera Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts: Camera Removable tape Remove the EDP cable Make sure the following FRUs (CRUs) have been removed.
“Remove the camera rubbers” on page 47 “Remove the camera” on page 47 “Remove the EDP cable” on page 48 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: LCD cover Chapter 4 Removing a FRU or CRU...