Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. sAfety
wArNiNG! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
wArNiNG! disconnect from air supply before changing drill bits, or servicing ,or performing any maintenance.
‰
Maintain the drill in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
Before each use check condition of drill bit. Sharpen if necessary. If worn or damaged replace immediately.
9
ensure the speed rating (rpm) of the drill bit is the same as, or greater than, the speed rating of the drill.
9
ensure there are no flammable or combustible materials near the work area.
9
evaluate your working area before using the drill. Ceilings, floors and enclosures may contain hidden electrical wiring, water pipes or
9
gas pipes.
wArNiNG! Always wear approved eye (and/or face) and hand protection when operating the drill.
‰
Use face, dust, or respiratory protection in accordance with CoSHH regulations.
9
depending on the task, the drilling noise level may exceed 84dB in which case wear safety ear defenders.
9
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. Do Not over reach, ensure the floor is not slippery, wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the drill. never hold a workpiece by hand.
9
Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.
9
Avoid unintentional starting.
9
wArNiNG! ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure all connections are secure.
9
Prolonged exposure to vibration from this drill poses a health risk. It is the owner's responsibility to correctly assess the potential hazard
9
and issue guidelines for safe periods of use and offer suitable protective equipment.
Do Not use the drill for a task it is not designed to perform.
8
Do Not operate drill if any parts are damaged or missing as this may cause failure and/or personal injury.
8
wArNiNG! Do Not drill any materials containing asbestos.
‰
Do Not carry the drill by the hose, or yank the hose from the air supply.
‰
Do Not force, or apply heavy pressure to the drill; let the tool do the work.
‰
Do Not place air line attachments close to your face and Do Not point at other people or animals.
‰
Do Not operate drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
‰
Do Not use drill where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags
‰
etc.
Do Not carry the drill with your finger on the trigger.
‰
Do Not direct air from the air line at yourself or others.
‰
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. iNtroDuCtioN
Polished aluminium housing with textured grip handle and planetary gear drive assembly. Fitted with Ø10mm Jacobs keyless chuck.
Suitable for general workshop use.
3. speCifiCAtioN
Model no: ................................................................... SA241
Air Consumption: ........................................................... 4cfm
Chuck Size: ............................................................... Ø10mm
Free Speed: ............................................................. 1800rpm
nett Weight: .................................................................. 1.1kg
noise Power/Pressure: ...................................... 100/91dB(A)
operating Pressure: ...................................................... 90psi
Vibration/Uncertainty: ......................................... 0.89/1.5m/s²
© Jack Sealey limited
Air Drill Ø10mm reversible with
Keyless ChuCK
Model no:
Wear protective
Wear ear
gloves
protection
Original Language Version
sA241.v2
Wear a mask
SA241.V2 Issue 1 29/11/18
Advertisement
Related Manuals for Sealey SA241.V2
Summary of Contents for Sealey SA241.V2
- Page 1 Model no: thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Vibration may cause failure if a quick change coupling is connected directly to the tool. To overcome this, connect a leader hose - Sealey model number AH2R or AH2R/38 - to the drill.. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig 1 & 2.
- Page 3 6.1. If the air supply does not have an oiler, lubricate the drill daily with a few drops of good grade air tool oil, such as Sealey ATo/500 or ATo/1000, dripped into the air inlet before use or dispensed automatically through an air system oiler.
- Page 4 Please note that the most effective protection is prevention, please refer to the Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website www. hse.gov.uk - Hand-Arm Vibration at Work. Original Language Version SA241.V2 Issue 1 29/11/18 © Jack Sealey limited...