Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1.
ELECTRICAL SAFETY
FWARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight. Double insulated products, which are always marked with
this symbol
, are fitted with live (brown) and neutral (blue) wires only. To rewire,
connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. This product requires more than 13 amps and is supplied without a plug. We recommend you contact a qualified electrician to ensure that a
suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cablecore section is important and should be at least 1.5mm
that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend
the use of 2.5mm
section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.
2
1.2
GENERAL SAFETY
WARNING! Water and Electricity are dangerous partners. Be extremely cautious and always be aware that this device uses an
F
electric motor. Always plug into an RCD (See
electrical safety above). Unplug from mains before changing accessories or servicing.
WARNING! DO NOT USE the washer if any part of the unit, gun, nozzle, detergent bottle, hose or cables is damaged. Replace or
F
repair using genuine parts only. Unauthorised parts may be dangerous and will invalidate your warranty. Always check connections
are correctly secured and not cracked or damaged in any way before using the machine.
WARNING! Use washer on a flat, levelled surface, with the handle in a vertical position. Failure to do so will invalidate your
F
warranty. NEVER use the washer tipped backwards or with the handle in a horizontal position .
Always be aware of the potential hazards that may occur during use. Study the applications and limitations of the washer before use.
"
Keep the washer in good condition. Use an authorised agent to service the unit.
"
Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.
"
Use where air can freely circulate around the washer to avoid the machine over-heating.
"
WARNING! Ensure all persons and animals keep at a minimum distance of 15 mtrs from the washer when in use.
F
WARNING! The pressure washer must only be used with clean water. Non-filtered water or corrosive chemicals must not be used as
F
they will damage the cleaner.
Ensure you comply with all local water supply regulations. Power washers may only be connected to mains drinking water supply
"
if a valve to prevent back flow is installed in the supply hose, or at the tap outlet.
Position the washer as near to the water supply as possible.
"
The supply hose must must be reinforced, and have an internal diameter of 13mm. The water supply must be at least equal to the cleaner
"
capacity. The water temperature must NOT exceed 122
Ensure the nozzle is aimed correctly at the working surface before activating the jet.
"
Before operating the trigger, GRIP the gun firmly to counteract the recoil from the high pressure water jet.
"
WARNING! Avoid sudden bursts of water as such will cause water pressure to drop and put extreme pressure on hoses and connectors.
F
If, during operation, power failure occurs turn the electricity and water off for safety reasons (but see para. 4.4. Note b).
"
WARNING! The high pressure jet will cause loose particles to be propelled at high speed, which may cause serious injury.
F
INSTRUCTIONS FOR:
P R E S S U R E WA S H E R S
PC1853 & PC2003
:
Models
F (50
C). The water supply pressure must NOT exceed 145psi (10 bar).
O
O
, but to be absolutely sure
2
PC1853 & PC2003 - 1 - 110303
Advertisement
Related Manuals for Sealey PC1853
Summary of Contents for Sealey PC1853
- Page 1 PC1853 & PC2003 Models Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 SPECIFICATIONS PC1853 ... .PC2003 Manifold Pressure ....1850psi ... . .2000psi Pressure at nozzle .
- Page 3 NOTE : Liquid detergent must be sprayed at low pressure. 4.1.1 Fill the detergent tank to the level indicated with a cleaning fluid such as Sealey AK131 General Purpose Detergent or Sealey AK133 Traffic Film Remover (fig.3). Where the clear pipe is attached to the washer you will find an adjustment screw which controls the water/detergent mix.
- Page 4 Worn piston packing Contact Authorised Service Agent Declaration of Conformity We, the sole importer into the UK of Sealey Power Products, declare that the products listed below are in conformity with the following standards and directives. The construction files for these product are held by the Manufacturer and Pressure Washers may be inspected, by a national authority, upon request to Jack Sealey Ltd.