Makita GA9080 Instruction Manual
Hide thumbs
Also See for GA9080:
- Instruction manual (148 pages) ,
- Instruction manual (125 pages) ,
- Instruction manual (120 pages)
Related Manuals for Makita GA9080
Summary of Contents for Makita GA9080
- Page 1 INSTRUCTION MANUAL Angle Grinder GA7080 GA7081 GA7082 GA9080 GA9081 GA9082 DOUBLE INSULATION Read before use.
- Page 2 SPECIFICATIONS Model: GA7080 GA7081 GA7082 GA9080 GA9081 GA9082 Wheel diameter 180 mm 230 mm Max. wheel thickness 7.2 mm 6.5 mm Spindle thread M14 or M16 or 5/8″ Rated speed (n) 8,500 min 6,600 min Overall length 509 mm 461 mm...
- Page 3 Work mode: surface grinding with normal side grip Model Vibration emission (a ) : (m/s ) Uncertainty (K) : (m/s GA7080 GA7081 GA7082 GA9080 GA9081 GA9082 Work mode: surface grinding with anti vibration side grip Model Vibration emission (a ) : (m/s ) Uncertainty (K) : (m/s...
- Page 4 WARNING: The vibration emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed. WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
- Page 5 Do not let familiarity gained from frequent use Keep handles and grasping surfaces dry, clean of tools allow you to become complacent and and free from oil and grease. Slippery handles and ignore tool safety principles. A careless action can grasping surfaces do not allow for safe handling and cause severe injury within a fraction of a second.
- Page 6 Wear personal protective equipment. Maintain a firm grip on the power tool and Depending on application, use face shield, position your body and arm to allow you to safety goggles or safety glasses. As appro- resist kickback forces. Always use auxiliary priate, wear dust mask, hearing protectors, handle, if provided, for maximum control over gloves and workshop apron capable of stop-...
- Page 7 Do not position your body in line with and Before using the tool on an actual workpiece, behind the rotating wheel. When the wheel, at let it run for a while. Watch for vibration or wobbling that could indicate poor installation the point of operation, is moving away from your or a poorly balanced wheel.
- Page 8 Switch handle mounting positions Country specific CAUTION: Switch can be locked in "ON" posi- Only for model GA7080 / GA9080 tion for ease of operator comfort during extended CAUTION: Always make sure that the switch use. Apply caution when locking tool in "ON"...
- Page 9 For tool with the lock-on and lock-off Soft start feature switch Only for model GA7080 / GA7081 / GA9080 / GA9081 Country specific Soft start feature reduces starting reaction. CAUTION: Switch can be locked in "ON" posi- tion for ease of operator comfort during extended use.
- Page 10 For tool with clamp lever type wheel The loop handle can be more comfortable than the original side grip for some applications. To install the loop handle, mount it guard onto the tool as illustrated and tighten two bolts to fix it. To remove the loop handle, follow the installation proce- Optional accessory dure in reverse.
- Page 11 Securely tighten the nut using a spanner, and then To tighten the lock nut, press the shaft lock firmly so close the lever in direction of the arrow to fasten the that the spindle cannot revolve, then use the lock nut wheel guard.
- Page 12 Installing or removing Ezynut Optional accessory Only for tools with M14 spindle thread. Mount inner flange, abrasive wheel and Ezynut onto the spindle so that Makita Logo on Ezynut faces outside. Fig.18 Installing or removing abrasive disc Optional accessory Fig.15 ►...
- Page 13 Installing or removing abrasive cut- Installing wire cup brush off / diamond wheel Optional accessory Optional accessory CAUTION: Do not use brush that is damaged, or which is out of balance. Use of damaged brush WARNING: When using an abrasive cut-off could increase potential for injury from contact with / diamond wheel, be sure to use only the special broken brush wires.
- Page 14 Dust collecting wheel guard for grinding (for model WARNING: Never vacuum metal particles GA7080 / GA7081 / GA9080 / GA9081) generated by operation. Metal particles generated by such operation are so hot that they ignite dust and the filter inside the vacuum cleaner.
- Page 15 For model GA7080 and GA9080, you can rotate the Grinding and sanding operation switch handle. Usage example: operation with abrasive cut-off wheel with GA7080 / GA9080 15° Fig.27 Turn the tool on and then apply the wheel or disc to the Fig.28...
- Page 16 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should Fig.32 be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. NOTE: Do not loosen the screw on the cover. Otherwise the cover may be opened accidentally.
- Page 17 The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Fig.36...
- Page 18 180 mm 230 mm Wheel guard for abrasive cut off wheel / diamond wheel *3 Inner flange 78 (Australia and New Zealand only) *4 Abrasive cut-off wheel / Diamond wheel Outer flange 78 (Australia and New Zealand only) *4 Back up pad Flex wheel Rubber pad Abrasive disc...
- Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885884A221 www.makita.com 20211124...