Advertisement
Quick Links
User's Manual
Large Format Display
MultiSync
M431-2
®
MultiSync
M501-2
®
MultiSync
M551-2
®
MultiSync
M651-2
®
MODEL: ME431, ME501, ME551, ME651, M431-2, M501-2, M551-2, M651-2
The regulations for this monitor applied to one of model names listed above.
Please find your model name on the label on the rear side of the monitor.
Advertisement
Related Manuals for NEC MultiSync M431-2
Summary of Contents for NEC MultiSync M431-2
- Page 1 User’s Manual Large Format Display MultiSync M431-2 ® MultiSync M501-2 ® MultiSync M551-2 ® MultiSync M651-2 ® MODEL: ME431, ME501, ME551, ME651, M431-2, M501-2, M551-2, M651-2 The regulations for this monitor applied to one of model names listed above. Please find your model name on the label on the rear side of the monitor.
- Page 2 Table of Contents Important Information ..........2 Recommended Use ............ 8 Recommended Use & Maintenance ......8 Maintenance ............... 8 Installation Chapter 1 Setup Overview ............10 Ventilation Requirements.......... 16 Mounting (for Customer)........... 13 Attaching Mounting Accessories....... 17 Mounting (for Trained Installers) ....... 14 Installing and Removing the Optional Table Top Stand .........
- Page 3 Advanced Operation Chapter 5 Creating a Power Schedule ........44 Password Security ............ 46 Using Picture Modes ..........45 Locking the Button Controls ........48 Setting Security and Locking the Monitor Controls... 46 Setting the Remote Control ID Function ....50 External Control Chapter 6 Controlling the Monitor via RS-232C ......
- Page 4 SLOT ................ 83 PICTURE ..............78 NETWORK ............... 85 AUDIO ..............81 PROTECT ..............86 SCHEDULE .............. 82 SYSTEM ..............89 Manufacturer’s Recycling and Energy Information Appendix D Disposing of your old NEC product ......92 Energy Saving ............92...
- Page 5 FCC Information WARNING: The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by Sharp NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment.
- Page 6 Important Information Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR: About the Symbols To ensure safe and proper use of the product, this manual uses a number of symbols to prevent injury to you and others as well as damage to property.
- Page 7 WARNING Handling the power cord. Do not scratch or modify the cord. • Do not place heavy objects on the cord. • Do not let the weight of the product rest on the cord. • Do not cover the cord with a rug, etc. •...
- Page 8 WARNING Do not install the product in the locations below: • Poorly ventilated spaces. • Near a radiator, other heat sources, or in direct sunshine. • Continual vibration areas. • Humid, dusty, steamy, or oily areas. • An environment where there are corrosive gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone, etc.).
- Page 9 WARNING Stability Hazard. The product may fall, causing serious personal injury or death. To prevent injury, this product must be securely attached to the floor/wall in accordance with the installation instructions. Many injuries, particularly to children, can be avoided by taking simple precautions such as: •...
- Page 10 CAUTION Handling the power cord. The monitor should be installed close to an easily accessible power outlet. REQUIRED When connecting the power cord to the product’s AC IN terminal, make sure the connector is fully and firmly inserted. An incomplete connection of the power cord may cause overheating of the plug; it allows dust to get on the plug connection, which can lead to a fire.
- Page 11 CAUTION Incorrect usage of batteries can result in leaks or bursting. • Use the specified batteries only. • Insert batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment. • Do not mix battery brands.
- Page 12 Power Cord Table European Plug Type North America U.K. Chinese Japanese Continental Plug Shape Region U.S.A./Canada U.K. China Japan Voltage 120* * Please use this power cord under 125 V power supply. NOTE: This product can only be serviced in the country where it was purchased. Recommended Use &...
- Page 13 Installation Chapter 1 This Chapter Includes: > “Setup Overview” on page 10 > “Mounting (for Customer)” on page 13 > “Changing the Logo Ornament Position” on page 13 > “Mounting (for Trained Installers)” on page 14 > “Orientation” on page 15 >...
- Page 14 Setup Overview 1. Determine the installation location NOTE: To avoid scratching the LCD panel, always place a soft cloth, such as a blanket that is larger than the monitor’s screen area, on the table before laying the monitor face down when installing the monitor stand or mounting accessories.
- Page 15 4. Connect the supplied power cord NOTE: Please make sure that enough power is supplied to the monitor. Please refer to the “Power Supply” in the specification (See “M431-2” on page “M501-2” on page “M551-2” on page 70 “M651-2” on page 71).
- Page 16 10. For long-term use The backlight used for this monitor has a limited life and its brightness decreases with the usage time. Also, if the same still image is shown for a long time, “Image Persistence” may occur. “Image Persistence” is a phenomenon in which the image of an LCD remains visible after the device has been turned off.
- Page 17 Install the logo ornament Screw hole with the screw which is used for installing the logo ornament. Protrusion Protrusion (Recommended Fasten Force: 30-40 N•cm). NOTE: Do not use any other screw to install the logo ornament. Inside of NEC logo ornament English−13...
- Page 18 Mounting (for Trained Installers) Carefully inspect the location where the unit is to be mounted. Not all walls or ceilings are capable of supporting the weight of the unit. The weight of this monitor is provided in the specifications (see “M431-2”...
- Page 19 Installing a safety wire NOTE: When installing, do not apply pressure to the LCD panel or excessive force to any part of the monitor by pushing or leaning on it. This may cause the monitor to become distorted or damaged. Handles for safety wire Attach the safety wire to the handles shown in the figure below.
- Page 20 Ventilation Requirements When mounting in an enclosed space or recessed area, leave adequate room between the monitor and the enclosure to allow heat to disperse, as shown below. ≥ 100 mm ≥ 30 mm ≥ 100 mm <40 °C NOTE: •...
- Page 21 Attaching Mounting Accessories The monitor is designed for use with the VESA mounting system. Be careful to avoid tipping the monitor when attaching accessories. VESA Mounting Interface M6 (M431-2/M501-2/M551-2), M8 (M651-2) 200 mm (M431-2) 400 mm (M501-2/M551-2/M651-2) 200 mm (M431-2) 400 mm (M501-2/M551-2/M651-2) Mounting accessories can be attached with the monitor in the face down position.
- Page 22 Installing and Removing the Optional Table Top Stand For installation, follow the instructions included with the stand or mounting equipment. Use only those devices recommended by the manufacturer. NOTE: • M431-2, M501-2, and M551-2 use ST-43M. M651-2 use ST-65M. • For the ST-43M, ONLY use screws which are included with the optional table top stand. For the ST-65M, ONLY use thumbscrews and attach the stand holders which are included with the optional table top stand.
- Page 23 Height adjustment (M551-2) 1. The lines on the stand pole are indicators of the height adjustment (Figure 1). Please adjust the pipe to the lines. Pipe M551-2 High/Low M431-2, M501-2 Adjust the pipe to a line. Figure 1 2. Please install the stand pole and the pipe with included screws. Please screw the two screw holes at the pipe (Figure 2). Pipe Stand pole Figure 2...
- Page 24 Parts Names and Functions Chapter 2 This Chapter Includes: > “Control Panel” on page 21 > “Terminal Panel” on page 22 > “Wireless Remote Control” on page 24 English−20...
- Page 25 Control Panel + Button (plus button) Increases the audio output level when the OSD menu is closed. Acts to move the highlighted area to the right when navigating through the OSD menu options. Acts as a plus button to increase the adjustment of an OSD menu option after it has been selected with the INPUT/SET button.
- Page 26 Terminal Panel HDMI LAN IN AUDIO OUT DisplayPort IN HDMI IN (ARC) HDMI IN REMOTE AC IN Connector LAN Port IN (RJ-45) Connects with the supplied power cord. Connect to LAN in order to manage and control the monitor over the network. See page Main Power Switch AUDIO OUT...
- Page 27 RS-232C IN (D-Sub 9-pin) Connect RS-232C input from external equipment, such as a computer, in order to control RS-232C functions. page Internal Speaker Handle Two for M431-2, M501-2, and M551-2. Four for M651-2. Security Slot Security and theft protection lock slot compatible with Kensington security cables/equipment.
- Page 28 Wireless Remote Control KEYPAD Press the buttons to set and change passwords, change the channel and set the REMOTE ID. See page ENT Button Makes selections in the Media Player settings. page DISPLAY Button Shows/Hides the information OSD. See page Unlocks the remote control’s buttons if they have been locked in the [LOCK SETTINGS] in the [PROTECT] menu.
- Page 29 MUTE Button Mutes the monitor’s audio and video output. Press it again to unmute the monitor’s audio and video output. See “MUTE SETTING* ” on page 90 for details. PICTURE MODE Button Cycles through the picture modes [NATIVE], [RETAIL], [CONFERENCING], [HIGHBRIGHT], [TRANSPORTATION] and [CUSTOM].
- Page 30 Connections Chapter 3 This Chapter Includes: > “Wiring Diagram” on page 27 > “Connecting to a Personal Computer” on page 28 > “Connecting to a Computer with HDMI” on page 28 > “Connecting a Computer with DisplayPort” on page 28 >...
- Page 31 Wiring Diagram LAN IN AUDIO OUT DisplayPort IN USB storage HDMI IN (ARC) HDMI IN REMOTE device. Computer (DisplayPort) HDMI video player or Dotted lines = other signal Computer (HDMI) Solid lines = video signal Blu-ray or Dashed lines = audio signal DVD Player Amplifier (HDMI)
- Page 32 Connecting to a Personal Computer Connecting to a Computer with HDMI • Please use an HDMI cable with the HDMI logo. • It may take a moment for the signal to appear after turning on the computer. • Some display cards or drivers may not show an image correctly. •...
- Page 33 Connecting to a Media Device with HDMI Connect using a single HDMI cable for the highest picture and audio quality from Blu-ray players, streaming media players, or game consoles. 4K UHD content is shown when the connected media player also supports 4K content. Supports HDCP (High-bandwidth Digital Contents Protection) coding, a type of digital rights management that prevents high- definition content, in Blu-ray discs, DVDs and streaming media, from being copied or broadcast illegally.
- Page 34 HDMI-CEC Command Please connect a HDMI-CEC compatible device to HDMI port. OSD menu HDMI-CEC command name Explanation Setting One Touch Play When a HDMI-CEC compatible device is turned INPUT-ADVANCED: (Consumer on, the monitor connected to the device by an INPUT SIGNAL SETTINGS DisplayPort AUTO TURN OFF Electronics...
- Page 35 Internal Video Sources Media Player The internal Media Player will play audio and video files that are stored on a USB storage device. See page 40 instructions on using the Media Player. Connect compatible USB storage device Format a USB storage device in the NTFS format, FAT32 format, or FAT16 format to use it with the Media Player. Refer to the computer’s instruction user’s manual or Help file on how to format a USB storage device.
- Page 36 Using the USB Port • USB storage device reader for use with the internal Media Player. See page • Power supply port. • Updates the monitor firmware via a USB storage device. • Imports or exports the monitor settings via the USB storage device when selecting [CLONE SETTING]. NOTE: ...
- Page 37 Basic Operation Chapter 4 This Chapter Includes: > “Power ON and OFF Modes” on page 34 > “Operating Range for the Remote Control” on page 35 > “Using Power Management” on page 35 > “Showing the Information OSD” on page 36 >...
- Page 38 Power ON and OFF Modes Press the ⏻ button on the Control Panel or POWER ON button on the remote control to turn on the monitor. The monitor’s power LED indicates the current status of the monitor. Please refer to the following table for information about the power indicator.
- Page 39 Operating Range for the Remote Control Point the top of the remote control toward the monitor’s remote control sensor during button operation. Use the remote control within a distance of about 7 m (23 ft.) from the remote control sensor, or at a horizontal and vertical angle of within 30° and within a distance of about 3.5 m (10 ft.).
- Page 40 Showing the Information OSD The Information OSD provides information such as: Input Source, etc. Press the DISPLAY button on the remote control to bring up the Information OSD. Input name DisplayPort 3840 x 2160＠60Hz Input Signal Information HDR Information Communication Info* * Shows when [COMMUNICATION INFO] is [ON].
- Page 41 Setting the Aspect Ratio Press the ASPECT button on the remote control to cycle through the options available for the current input signal. NOTE: [Media Player] is not available. [FULL] [WIDE] [1:1] [ZOOM] [NORMAL] ➙ ➙ ➙ ➙ Aspect ratio of Recommended selection for picture Unchanged view* Description...
- Page 42 OSD (On-Screen Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item PICTURE: PICTURE MODE NATIVE BACKLIGHT RETAIL BACKLIGHT DIMMING CONFERENCING Adjustment Settings VIDEO BLACK LEVEL TRANSPORTATION Sub Menu GAMMA...
- Page 43 Below is a brief summary of where controls are under each menu item. A table listing all options is located in “OSD Controls List” on page INPUT: Select settings related to the input signal source. Configure the Media Player settings. PICTURE: Select one of the default picture modes, manually adjust the color settings, adjust the aspect ratio, and adjust other settings related to the picture.
- Page 44 Using the Media Player Menu The Media Player plays image, video, and music files Operation Buttons located on a USB storage device connected the USB port • Press the SET/POINT ZOOM button while playing a file on the monitor (see page 22).
- Page 45 Random Play - Repeat one file - Random Play • No selected files. - A file is playing: the current file plays on a loop. • Shuffles files to repeat play in a random order instead of - No file is playing: the highlighted file in the folder plays the file sorted order.
- Page 46 USB Drive Data and File Format Requirements Supported file system FAT16/32, NTFS Max. folder level Max. number of photos PHOTO mode File Extension Data format Min. Resolution (HxV) of Image Max. Resolution (HxV) of Image JPEG, JPG, JPE Baseline Sequential DCT 75x75 pixels 15,360x8,640 pixels MUSIC mode...
- Page 47 Advanced Operation Chapter 5 This Chapter Includes: > “Creating a Power Schedule” on page 44 > “Using Picture Modes” on page 45 > “Setting Security and Locking the Monitor Controls” on page 46 > “Password Security” on page 46 > “Locking the Button Controls” on page 48 >...
- Page 48 Creating a Power Schedule The schedule function allows the monitor to automatically change between power on and standby modes at different times. To program the schedule: 1. Enter the [SCHEDULE] menu. Using the remote control, highlight [SCHEDULE INFORMATION] using SCHEDULE: the ...
- Page 49 Using Picture Modes There are different picture modes available. These picture modes have also been configured with settings as described in the “Picture Mode Types” table below. To change picture modes: Press the PICTURE MODE button on the wireless remote control to cycle through the modes, or select the mode in the [PICTURE] list in the OSD menu.
- Page 50 Setting Security and Locking the Monitor Controls Under normal operation, the monitor can be controlled by any person using the remote control or the monitor control panel. You can prevent unauthorized use and changes to the monitor settings by enabling the options for Security and Lock Settings. The security and locking functions covered in this section are: •...
- Page 51 Set a password for the monitor This step is only required if you want to change the password. PROTECT: PASSWORD: POWER SAVE SETTINGS THERMAL MANAGEMENT o o o o SECURE MODE: SCREEN SAVER START-UP LOCK POWER ON DELAY CONTROL LOCK SECURITY SETTINGS LOCK SETTINGS CHANGE PASSWORD...
- Page 52 Locking the Button Controls The lock settings prevent the monitor from responding to button presses on the remote control or monitor control panel. When locking the button controls, some buttons can be configured to remain unlocked for users to adjust the settings. Locking and unlocking the button controls do not require a password.
- Page 53 Locking the Control Panel Buttons The [KEY] in the [LOCK SETTINGS] prevent the monitor from being controlled using the buttons on the monitor Control Panel. Enabling the [KEY] does not lock the buttons on the remote control. PROTECT: POWER SAVE SETTINGS SELECT THERMAL MANAGEMENT MODE...
- Page 54 Setting the Remote Control ID Function The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors.
- Page 55 External Control Chapter 6 This Chapter Includes: > “Controlling the Monitor via RS-232C” on page 52 > “Controlling the Monitor via LAN” on page 53 > “HTTP Browser” on page 54 > “Commands” on page 60 > “Proof of Play” on page 61 Connecting an external device There are two options to connect an external device to control the monitor.
- Page 56 Controlling the Monitor via RS-232C This monitor can be controlled by connecting a personal computer with an RS-232C (reverse type) terminal. NOTE: When you use this function, [CONTROL TERMINAL] in [EXTERNAL CONTROL] should be [RS-232C] (see page 89). For example, some of the functions that can be controlled by a personal computer are: •...
- Page 57 PIN ASSIGNMENT RS-232C input/output Pin No Name D-SUB 9P (Monitor side) This monitor uses RXD, TXD and GND lines for RS-232C control. Controlling the Monitor via LAN Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NOTE: ...
- Page 58 HTTP Browser Overview Connecting the monitor to a network allows for remote control of the monitor from a computer connected to the same network. This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. Refer to the help files for the web browser to change the settings to use JavaScript and Cookies.
- Page 59 OSD Menu Settings in the Monitor Web controls Select one of the links on the left side of the monitor web controls to configure the settings available in the monitor’s OSD. Please see page 75 for the full list of OSD menu controls. [INPUT], [PICTURE], [AUDIO], [SCHEDULE], [SLOT], [NETWORK], [PROTECT], [SYSTEM] NOTE: ...
- Page 60 Network Settings Click on “NETWORK” on the left-hand column below HOME. IP SETTING Select an option for setting the IP ADDRESS. AUTO: Automatically assign an IP address. MANUAL: Manually set an IP address for the monitor connected to the network. NOTE: Consult your network administrator if you have any trouble.
- Page 61 Mail Setting Click on “MAIL” on the left-hand column below HOME. When the Mail settings are configured and enabled, the monitor sends email notifications when an error occurs or if the input signal is lost. The monitor must be connected to a LAN for this feature to work. Alert Mail When an error occurs, the monitor will send an error message to the email address(es) listed in the Recipient’s Address fields.
- Page 62 SNMP Settings Click on “SNMP” on the left-hand column below HOME. The SNMP protocol is used to get status information and to control a monitor directly via the network. Version: SNMP v1 Authenticated plaintext by community name, does not return a confirmation message of the trap. SNMP v2c Authenticated plaintext by community name, returns a confirmation message of the trap.
- Page 63 CRESTRON Settings Click on “CRESTRON” on the left column below HOME. CRESTRON ROOMVIEW compatibility The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and controlled from a computer or a controller. For further information, visit https://www.crestron.com ROOMVIEW ROOMVIEW for managing from the computer.
- Page 64 This monitor supports control command, which is listed in the “External_Control.pdf” (See page 73), but also supports common ASCII control command, which is used for controlling the NEC monitor or projector from a connected computer. For further information please visit our website. NOTE: ...
- Page 65 Proof of Play This function allows sending of messages for the current status of the monitor by self-diagnosis. For the Proof of Play function including self-diagnosis, please see the “External_Control.pdf”. See page Check item Message INPUT DisplayPort, HDMI1, HDMI2, Media Player, COMPUTE MODULE, OPTION* Resolution e.g.
- Page 66 Troubleshooting Chapter 7 This Chapter Includes: > “Screen Image and Video Signal Issues” on page 63 > “No picture” on page 63 > “Image persistence” on page 63 > “The image is blinking” on page 63 > “The image is unstable, unfocused or swimming is apparent” on page 64 >...
- Page 67 Screen Image and Video Signal Issues No picture Image persistence • The signal cable should be completely connected to the • Please be aware that LCD Technology may experience display card/computer. a phenomenon known as image persistence. Image persistence occurs when a residual or “ghost” image of •...
- Page 68 The image is unstable, unfocused or swimming is Selected resolution is not displayed properly apparent • Check the Information OSD to verify the appropriate resolution has been selected. • The signal cable should be completely attached to the computer. • If the resolution you set is over or under a range, an “OUT of RANGE”...
- Page 69 Snowy picture, poor Sound in TV The monitor goes into standby automatically • Check antenna/cable connection. Use new cable if • Please check [OFF TIMER] setting. necessary. • Set the [CEC] function to [OFF]. The monitor may go into standby mode when a connected HDMI-CEC compatible The USB hub does not operate device goes into standby.
- Page 70 Specifications Chapter 8 This Chapter Includes: > “Compatible Signal List” on page 67 > “M431-2” on page 68 > “M501-2” on page 69 > “M551-2” on page 70 > “M651-2” on page 71 English−66...
- Page 71 Compatible Signal List Scanning frequency HDMI Signal name Resolution DisplayPort Remarks Horizontal Vertical MODE1 MODE2 640 x 480 31.5 kHz 60 Hz SVGA 800 x 600 37.9 kHz 60 Hz 1024 x 768 48.4 kHz 60 Hz 1280 x 720 45.0 kHz 60 Hz 1280 x 768...
- Page 72 M431-2 Product Specifications LCD Module 43”/108.0 cm diagonal Pixel Pitch: 0.245 mm Resolution: 3840 x 2160 Color: Over 1073 million colors (depending on display card used) Brightness* 500 cd/m (Max.) Contrast Ratio: 1200:1 Viewing Angle: 89° (typ) @ CR>10 Frequency Horizontal: 15 - 136 kHz Vertical:...
- Page 73 M501-2 Product Specifications LCD Module 50”/125.7 cm diagonal Pixel Pitch: 0.285 mm Resolution: 3840 x 2160 Color: Over 1073 million colors (depending on display card used) Brightness* 500 cd/m (Max.) Contrast Ratio: 4000:1 Viewing Angle: 89° (typ) @ CR>10 Frequency Horizontal: 15 - 136 kHz Vertical:...
- Page 74 M551-2 Product Specifications LCD Module 55”/138.8 cm diagonal Pixel Pitch: 0.315 mm Resolution: 3840 x 2160 Color: Over 1073 million colors (depending on display card used) Brightness* 500 cd/m (Max.) Contrast Ratio: 5000:1 Viewing Angle: 89° (typ) @ CR>10 Frequency Horizontal: 15 - 136 kHz Vertical:...
- Page 75 M651-2 Product Specifications LCD Module 65”/163.9 cm diagonal Pixel Pitch: 0.372 mm Resolution: 3840 x 2160 Color: Over 1073 million colors (depending on display card used) Brightness* 500 cd/m (Max.) Contrast Ratio: 1200:1 Viewing Angle: 89° (typ) @ CR>10 Frequency Horizontal: 15 - 136 kHz Vertical:...
- Page 76 United States and other countries. MultiSync is a trademark or registered trademark of Sharp NEC Display Solutions, Ltd. in Japan and other countries. PJLink trademark and logo are trademarks applied for registration or are already registered in Japan, the United States of America and other countries and areas.
- Page 77 Module, which is an optional component available for this model. The required DS1-IF20CE Compute Module Interface Board and Raspberry Pi Compute Module are available separately. Please contact an authorized NEC dealer or visit our website in your region for purchase information and availability.
- Page 78 This free software is an advanced and powerful network based control, monitoring and asset management system for NEC monitors and projectors. The software is available for Microsoft Windows and macOS. The latest version of the NaViSet Administrator software is available on our website.
- Page 79 OSD Controls List Appendix C This Chapter Includes > “INPUT” on page 76 > “PICTURE” on page 78 > “AUDIO” on page 81 > “SCHEDULE” on page 82 > “SLOT” on page 83 > “NETWORK” on page 85 > “PROTECT” on page 86 >...
- Page 80 INPUT INPUT MENU INPUT SELECT* DisplayPort Selects the input signals source. HDMI1 HDMI2 Media Player COMPUTE MODULE* OPTION* INPUT SETTINGS INPUT NAME* To rename the input: 1. Highlight the name field. 2. Press SET on the IR remote control to activate the field. •...
- Page 81 INPUT MENU ADVANCED* INPUT SIGNAL SETTINGS DisplayPort BIT RATE Sets the bit rate of the DisplayPort signal. If the image is unstable or picture noise occurs, please try the other settings. Options are: HBR/HBR2. NOTE: Some models are supporting BIT RATE automatically, function grayed out. HDMI Sets the HDMI mode.
- Page 82 INPUT MENU AUTO TURN OFF The HDMI-CEC compatible device goes into standby at the same time as the monitor when the STANDBY button is pressed on the remote control, or when the ⏻ button is pressed on the monitor. NOTE: The connected HDMI-CEC compatible device may not go into standby if it is recording.
- Page 83 PICTURE MENU GAMMA* Select a monitor gamma correction for best picture quality. Selection depends on the desired usage. NATIVE Gamma correction is handled by the LCD panel. Typical monitor gamma for use with a computer. Typical gamma settings for use with videos, such as DVDs and Blu-rays. S GAMMA Special gamma for certain types of movies.
- Page 84 PICTURE MENU AUTO DIMMING Adjusts the backlight of the LCD automatically depending on the amount of ambient light. AUTO BRIGHTNESS Adjusts the brightness level according to the input signal. NOTE: When [MODE1] or [MODE2] is selected in [AMBIENT LIGHT SENSING] at [ADVANCED], this function cannot be changed.
- Page 85 PICTURE MENU TILE MATRIX* Allows one image to be expanded and shown over multiple screens (up to 100) through a distribution amplifier. This option is for configuring the TILE MATRIX settings. NOTE: • Low resolution is not suitable for tiling to a large number of monitors. •...
- Page 86 AUDIO MENU EQUALIZER* TREBLE Accentuates or reduces the high frequency range of audio signals. Press the + button to increase [TREBLE]. Press the – button to decrease [TREBLE]. BASS Accentuates or reduces the low frequency sound. Press the + button to increase [BASS]. Press the –...
- Page 87 SLOT SLOT MENU ACTIVE SLOT Sets the active Option Board slot. NOTE: Only the selected input will work. OPTION* Configure settings for a connected Option Board. POWER CONTROL POWER SUPPLY Controls power to an Option Board. Select [ON] then press SET on the remote control to power on the device. Select [OFF] then press SET on the remote control to power off the device.
- Page 88 SLOT MENU POWER SETTING AUTO POWER UP The Compute Module will be turned on automatically when the monitor power is turned on. AUTO SHUTDOWN The Compute Module is turned off when the monitor switches into standby mode. POWER SUPPLY This sets the time delay after the Shutdown Signal is set until the power to the Compute Module is turned OFF DELAY off.
- Page 89 NETWORK NETWORK MENU NETWORK INFORMATION Configures the monitor’s network settings either automatically or manually. IP SETTING When [AUTO] is selected, the IP address is automatically obtained from the DHCP server. When [MANUAL] is selected, the network settings must be entered manually. Contact the Network Administrator for this information.
- Page 90 PROTECT PROTECT MENU POWER SAVE SETTINGS* POWER SAVE Enables or disables the monitor entering power saving mode. When [ENABLE] is selected, the monitor goes into power saving mode after the period of time has passed with no input signal detected or signal loss has occurred. You can set the power saving condition in [MODE].
- Page 91 PROTECT MENU SCREEN SAVER* Use the [SCREEN SAVER] function to reduce the risk of Image Persistence. NOTE: • When the screen saver starts, the image aspect is changed to [FULL]. When the screen saver stops, the aspect will return to the current [ASPECT] setting. •...
- Page 92 PROTECT MENU POWER Select [UNLOCK] to be able to use the POWER button when all buttons are locked. Select [LOCK] to lock the button. VOLUME When [IR] is selected in [SELECT]: - UNLOCK: Enable to control the volume with the VOL +/– button on the remote control. When [KEY] is selected in [SELECT]: - UNLOCK: Enable to control the volume with the + button and the –...
- Page 93 SYSTEM SYSTEM MENU MONITOR INFORMATION Shows the model name, serial number and firmware version of the monitor. [CARBON SAVINGS]: Shows the estimated carbon saving information in kg-CO2. The carbon footprint factor in the carbon saving calculation is based on the OECD (2008 Edition). [CARBON USAGE]: Shows the estimated carbon usage information in kg-CO2.
- Page 94 SYSTEM MENU OSD TIME* Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds. OSD POSITION* Determines the location where the OSD appears on the screen. OSD SIZE* Change the size of the OSD on the screen. INFORMATION OSD* Selects whether or not to automatically show information about the monitor when it powers on, changes input, or the current input signal changes.
- Page 95 Appendix D Energy Information This Chapter Includes: > “Disposing of your old NEC product” on page 92 > “Energy Saving” on page 92 > “WEEE Mark (European Directive 2012/19/EU and amendments)” on page 92 We are strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment.
- Page 96 Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, we offer a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.