NEC ASPV46-AVT - AccuSync - 46" LCD TV Setup
Accusync pv series external control device setup
Hide thumbs
Also See for ASPV46-AVT - AccuSync - 46" LCD TV:
- Brochure (4 pages) ,
- User manual (60 pages) ,
- Specification sheet (2 pages)
Advertisement
Table of Contents
AccuSync PV Series External Control Device Setup
Connect the RS-232 input jack to a control device (such as a
computer or an A/V control system) in order to control the set's
functions externally.
Connect External Equipment
Y
Pb
Pr
COMPONENT IN
Connect the serial port of the control device to the RS-232 jack on
the set.
RS-232 connection cables are not supplied with the Monitor.
The Monitor remote control and front panel controls (except main
power) will not be functional if the set is controlled by a PC
computer or other external device.
RJ-45 8PIN CONNECTOR
< Back panel of the set >
S-VIDEO IN
RS-232
SERVICE
1
2
3
4
...
NO.
PIN NAME
1
RXD(RECEIVE DATA)
2
TXD(TRANSMIT DATA)
3
GND
4
GND
5
NO CONNCETION
6
NO CONNCETION
7
NO CONNCETION
8
NO CONNCETION
Communication Parameters
• Baud rate : 9600bps (UART)
• Data length : 8bits
• Parity : None
• Stop bit : 1bit
• Communication code : HEX code
8
7
6
5
4
1
2
1
3, 4
1
2
3
Advertisement
Table of Contents
Related Manuals for NEC ASPV46-AVT - AccuSync - 46" LCD TV
Summary of Contents for NEC ASPV46-AVT - AccuSync - 46" LCD TV
- Page 1 AccuSync PV Series External Control Device Setup Connect the RS-232 input jack to a control device (such as a computer or an A/V control system) in order to control the set’s functions externally. Connect External Equipment < Back panel of the set > S-VIDEO IN RS-232 COMPONENT IN...
-
Page 2: External Control Device Setup
External Control Device Setup Hyper Terminal Setting 1. Run ‘Start > Programs > Accessories > Communications > Hyper Terminal’. 2. Enter a name and chose an icon for the connection. - Page 3 External Control Device Setup Hyper Terminal Setting 3. Enter your Serial(RS-232) Port number. (For example, ‘set to COM1, COM2 or etc.) 4. Set up the port setting as below - Bits per second : 9600 - Data bits : 8 - Parity : None - Stop bits : 1 - Flow control : None...
- Page 4 External Control Device Setup Hyper Terminal Setting 3. Open ‘File > Properties’. 4. Chose the ‘Setting’ tab and click the ‘ASCII Setup’ button as following image.
-
Page 5: Set Id
External Control Device Setup Hyper Terminal Setting 3. Check the following items in the ‘Settings’ tab as below. - ‘Send line ends with line feeds’ - ‘Echo typed characters locally’ - ‘Append line feeds to icomming line ends’ - ‘Wrap lines that exceed terminal width’ Set ID SETUP Press the MENU button and then... -
Page 6: Command Reference List
External Control Device Setup Command Reference List COMMAND1 COMMAND2 DATA(Hex) 01. Power 02. Input Select 0~8(32"), 0~9(40", 46") 03. Aspect Ratio 0~5(TV~Svideo), 0~1(DTV, Com~HDMI3) 04. Volume Mute 05. Screen Mute 06. Contrast 0~64 07. Brightness 0~64 08. Color 0~64 09. Tint 0~64 10. - Page 7 External Control Device Setup 02. Input Select (Command 2 : b) Transmission / Receiving Protocol To select input source for the Monitor. Transmission You can also select an input source using the INPUT button on the Monitor's remote control. [Command1][Command2][ ][SetID][ ][Data][Cr] Transmission * [Command1] : First Command (k or t) [k][b][ ][Set ID][ ][Data][Cr]...
- Page 8 External Control Device Setup 06. Contrast (Command 2 : f) 10. Sharpness (Command 2 : j) To adjust screen contrast. To adjust screen sharpness. You can also adjust contrast in the PICTURE menu. You can also adjust sharpness in the PICTURE menu. Transmission Transmission [k][f][ ][Set ID][ ][Data][Cr]...
- Page 9 External Control Device Setup 14. PIP Mode (Command 2 : n) 18. Balance (Command 2 : r) To select PIP mode. To adjust sound balance. You can also adjust PIP Mode in the Main/PIP menu. You can also adjust balance in the SOUND menu. Transmission Transmission [k][n][ ][Set ID][ ][Data][Cr]...
- Page 10 External Control Device Setup 23. PC Reset (Command 2 : w) * Real data mapping To select the PC Reset. Step 0 Step 51 You can also setting Restores factory. Step 1 Step 52 Transmission Step 2 Step 53 Step 3 Step 54 [k][w][ ][Set ID][ ][Data][Cr] Step 4...