Product overview This section will provide information on adjusting monitor positions, setting user controls, and using the cable lock slot. Types of adjustments Tilt Please see the illustration below for an example of the tilt range. Swivel With the built-in pedestal, you can tilt and swivel the monitor for the most comfortable viewing angle.
Height Adjustment After pressing the top of the monitor, remove the fixed pin and adjust the height of the monitor. 110mm Monitor Pivot - Adjust height to the top position before rotation the monitor. - Rotate clockwise until the monitor stops at 90° User controls Your monitor has controls on the front which are used to adjust the display.
Cable lock slot Your monitor is equipped with a cable lock slot located on the rear of your monitor (in the lower right corner). Please follow the instructions that came with the cable lock to attach it. Setting up your monitor This section provides information to help you set up your monitor.
Page 9
Connect the digital cable to the DVI connector of the monitor and the other end on the back of the computer. Connect one end of the USB hub cable to the USB connector on the back of the computer, and the other end to the upstream USB connector on the monitor. Chapter 1.
Page 10
Plug the monitor power cord and the computer cord into grounded electrical outlets. Note: A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0.75mm or H05VVH2-F2 3G 0.75mm...
Page 11
Remove the Hook from the back of the stand. Rotate the head of the monitor into portrait view. Chapter 1. Getting started...
Page 12
Place the cables through the Main Clip. Then fasten the clip. Wrap the Cable Wapper around the cables. L190x Flat Panel Monitor User’s Guide...
Page 13
Replace the Hook. Replace the Cable Cover. Chapter 1. Getting started...
Page 14
Power on the monitor and the computer. To install the monitor driver, insert the Reference and Driver CD, click Install driver, and follow the on-screen instructions. To optimize your monitor image, if using the analog cable, press the Automatic Image Setup key. Automatic image setup requires that the monitor is warmed up for at least 15 minutes.
Thank you for purchasing this Lenovo™ product. Please take a few moments to register your product and provide us with information that will help Lenovo to better serve you in the future. Your feedback is valuable to us in developing products and services that are important to you, as well as in developing better ways to communicate with you.
· Tilt: Adjust the tilt of your monitor to optimize the appearance of the screen content and to accommodate your preferred head and neck posture. · General location: Position your monitor to avoid glare or reflections on the screen from overhead lighting or nearby windows. The following are some other tips for comfortable viewing of your monitor: ·...
Accessibility information Lenovo is committed to providing greater access to information and technology to people with disabilities. With assistive technologies, users can access information in the way most appropriate to their disability. Some of these technologies are already provided in your operating system; others can be purchased through vendors or accessed at: http://www.ibm.com/able/...
Page 19
To use the controls: 1. Press to open the main OSD menu. 2. Use to move among the icons. Select an icon and press to access that function. If there is a sub-menu, you can move between options using then press to select that function.
Table 2-2. OSD functions OSD Icon Submenu Description Controls and Controls on Main Adjustments Menu (Analog) Adjustments (Digital) Adjusts overall brightness Same as Brightness Analog Brightness- Adjusts difference between light and dark areas /Contrast Contrast Moves the image left or right. Controls Image Horizontal Position...
Table 2-2. OSD functions (continued) OSD Icon on Submenu Description Controls and Controls and Main Menu Adjustments Adjustments (Analog) (Digital) Adjusts menu location on the screen. Same as Analog Options Menu Position Default Returns the menu position to the default settings. Custom ·...
The display modes shown below have been optimized at the factory. Table 2-3. Factory set display modes Addressability Refresh rate 640 x 350 70 Hz 640 x 480 60 Hz, 66 Hz, 72 Hz, 75 Hz 720 x 400 70 Hz 800 x 600 60 Hz, 72 Hz, 75 Hz 1024 x 768...
For optimal performance, switch off your monitor at the end of each working day, or whenever you expect to leave it unused for long periods during the day. Table 2-4. Power indicator State Power Indicator Screen Restoring Operation Compliance Steady green Normal Standby/Suspend Steady amber...
Detaching the monitor stand After placing the monitor face down on a clean surface or soft cloth, remove the four screws from the stand to remove it from the monitor. L190x Flat Panel Monitor User’s Guide...
Page 26
Table 3-1. Monitor specifications for type-model 4439-HB2 (continued) Communications VESA DDC Supported Display Modes Horizontal frequency 30 kHz - 75 kHz (VESA Standard modes Vertical frequency 50 Hz - 75 Hz between noted ranges) Native Resolution 1280 x 1024 at 60 Hz Temperature Operating to 45...
Troubleshooting If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your dealer or Lenovo, try the suggested actions that are appropriate to your problem. Table 3-2. Troubleshooting Problem...
This is a characteristic If there are more than five pixels Appendix A, "Service of the pixels of the LCD technology missing, contact the IBM and Support," on page Lenovo appear and is not an LCD Support Center. discolored defect. Fuzzy lines...
(where X is the drive letter designator for the CD-ROM drive). Select the "L190xC.inf" file and click the Open button. Click the OK button. Select Lenovo L190xC and click Next. The files will be copied from the CD to your hard disk drive.
(where X is the drive letter designator for the CD-ROM drive). Select the "L190xC.inf" file and click the Open button. Click on the OK button. Select Lenovo L190xC and click Next. The files will be copied from the CD to your hard disk drive.
(where X is the drive letter designator for the CD-ROM drive). Select the "L190xC.inf" file and click the Open button. Click on the OK button. Select Lenovo L190xC and click Next. The files will be copied from the CD to your hard disk drive.
Manually installing the Soft OSM Below are steps for manually installing the Soft OSM. Insert Lenovo Monitor CD into the CD drive. The CD menu displays. Select “Install Soft OSM” and follow the on-screen instructions. Or you can navigate to the following directory to find Soft OSM setup program: X:\Soft OSM Drivers (where X is the drive letter designator for the CD-ROM drive).
Page 33
It will take several seconds to copy the files to your computer. When the View Readme File dialog box appears, click OK. Restart your computer. After the computer has started up, you can see a monitor icon in the lower right hand corner of the desktop.
Getting further help If you still can’t solve your problem, please contact the Lenovo Support Center. For more information on contacting the Customer Support Center, please see Appendix “Service and Support,” on page A-1. Service information Product numbers The product number for your monitor is located on the side of the display bezel as shown below.
Service parts The following parts are for use by Lenovo service, or Lenovo authorized dealers, to support the customer warranty. Parts are for service use only. The table below shows information for model 4439-HB2. Table 3-3. List of service parts...
Telephone technical support Installation and configuration support through the Customer Support Center will be withdrawn or made available for a fee, at Lenovo’s discretion, 90 days after the option has been withdrawn from marketing. Additional support offerings, including step-by-step installation assistance, are available for a nominal fee.
Page 37
Country or Region Telephone Number Africa Africa: +44 (0)1475-555-055 South Africa: +27-11-3028888 and 0800110756 Central Africa: Contact the neares Lenovo Business Partner Argentina 0800-666-0011 (Spanish) Australia 131-426 (English) Austria Up and running support: 01-24592-5901 Warranty service and support: 01-211-454-610 (German)
Page 38
Country or Region Telephone Number Ecuador 1-800-426911 (Spanish) El Salvador 250-5696 (Spanish) Estonia +386-61-1796-699 Finland Up and running support: 09-459-6960 Warranty service and support: +358-800-1-4260 (Finnish) France Up and running support: 0238-557-450 Warranty service and support (hardware): 0810-631-213 Warranty service and support (software): 0810-631-020 (French) Germany Up and running support: 07032-15-49201...
Page 39
Country or Region Telephone Number Japan Both of the above numbers will be answered with a Japanese language voice prompt. For telephone support in English, please wait for the Japanese voice prompt to end, and an operator will answer. Please ask for ¡²English support please,¡² and your call will be transferred to an English speaking operator.
Page 40
Country or Region Telephone Number Slovenia +386-1-4796-699 Spain 91-714-7983 91-397-6503 (Spanish) Sri Lanka +94-11-2448-442 (English) Sweden Up and running support: 08-477-4420 Warranty service and support: 077-117-1040 (Swedish) Switzerland Up and running support: 058-333-0900 Warranty service and support: 0800-55-54-54 (German, French, Italian) Taiwan 886-2-8723-9799 (Mandarin) Thailand...
The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.