free stats
NEC Versa S940 Disassembly Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Laptop
  5. Versa S940
  6. Disassembly manual

NEC Versa S940 Disassembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Versa S940
Disassembly Manual

Advertisement

Table of Contents
loading

Related Manuals for NEC Versa S940

Summary of Contents for NEC Versa S940

  • Page 1 Versa S940 Disassembly Manual...

  • Page 2: Table Of Contents

    Removing the LCD Module ..........................15 Removing the LCD Panel.............................17 Removing the Top Cover .............................19 Removing the Main Board............................21 Removing the Speaker Assembly ........................23 Removing the Touch Pad.............................23 DIP Switch Settings..............................24 Screws..................................24 Notice ...................................25 NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 2...

  • Page 3: Overview

    Furthermore, the screws that are removed are shown next to the image of the parts themselves. NEC reserves the right to make changes to the Versa S940/EasyNote A7 chassis without notice. Technician Notes Only technicians authorized by NEC Computers International BV should attempt to repair this equipment.

  • Page 4: Hazardous Voltage

    Inside the power supply are hazardous avviare il sistema senza aver prima messo a voltages that can cause serious personal injury. Always posto il coperchio return a defective power supply to your dealer. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 4...

  • Page 5: Removing The Battery

    Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the Versa S940/EasyNote A7. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig.

  • Page 6: Removing The Memory Module

    Fig. 2 Removing the screws retaining the memory module slot cover 2. Unclip the memory module as shown in Fig. 3 Fig. 3 Removing the memory module 3. Remove the memory module from its slot and put it aside. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 6...

  • Page 7: Removing The Wlan Card Module

    1. Disconnect the wireless antenna connector and release the WLAN Card Module as shown in Error! Reference source not found. Fig. 4 WLAN Card Module 2. Lift up the WLAN Card Module and put it aside. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 7...

  • Page 8: Removing The Hard Disk Drive

    1. Remove the screws as shown in Fig. 5 M2.5x8 Copper Fig. 5 Removing the Hard disk drive cover 2. Carefully pull the HDD module out from the base unit. Fig. 6 Pulling HDD module NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 8...
  • Page 9 3. Remove four screws that around HDD module. M4x3 Silver Fig. 7 HDD module Note: When installing HDD, make sure the HDD module strap properly insert into base unit as shown in below picture. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 9...

  • Page 10: Removing The Optical Disk Drive

    Fig. 8 Eject the optical drive 1. Pull the ODD module out from the base unit as shown in Fig. 9 Fig. 9 Pulling the optical drive out from the base unit NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 10...

  • Page 11: Removing The Cpu

    CPU Heat Sink in descending order (3 2 1) as shown in Fig. 11 A = M2.5x5 Black Fig. 11 CPU Heat Sink Note: When install CPU heat sink, screws must be secured in ascending order (1 2 3). NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 11...
  • Page 12 3. Unlock the CPU from the CPU socket and lift up the CPU carefully. Fig. 12 Unlocking the CPU NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 12...

  • Page 13: Removing The Keyboard

    1. Release two screws on keyboard cover as shown in Fig. 13 M2x4.5 Black Fig. 13 Releasing the keyboard cover 2. Lift up the keyboard cover carefully as shown in Fig. 14 Fig. 14 Lifting up the Keyboard Cover NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 13...
  • Page 14 Caution: If using wrong screws during keyboard assemble might result damage to keyboard. Thus please mark those screws carefully during dissemble. 4. Flip over the unit and release remaining screw holding keyboard as shown in Fig. 16 M2.5x3 Silver Fig. 16 Screw holding Keyboard NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 14...

  • Page 15: Removing The Lcd Module

    WLAN Card Module (see Removing WLAN Card Module)and remove the Keyboard (see Removing the Keyboard) then perform the following steps: 1. Release LCD cable from base unit. Fig. 18 Releasing LCD cable NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 15...
  • Page 16 2. Disconnect LCD Cable Connection and remove four screws retaining the Heat Plate as shown in Fig. 19 M2.5x6 Silver Fig. 19 Removing the screws retaining the LCD module 3. Carefully lift up the LCD Module. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 16...

  • Page 17: Removing The Lcd Panel

    B = M2.5x5 Black Fig. 20 Removing the rubber covers & screws on the LCD Module 3. Carefully removing the LCD Bezel as shown in Fig. 21 Fig. 21 Removing the LCD Bezel NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 17...
  • Page 18 7. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. 24 M2x4 Silver Fig. 24 Removing the LCD Panel hinges NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 18...

  • Page 19: Removing The Top Cover

    D = M2.5x6 Silver E = M2.5x8 Copper Fig. 25 Bottom Cover 2. Release two screws at the rear of system as shown in Fig. 26 M2.5x5 Black Fig. 26 Rear view NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 19...
  • Page 20 3. Disconnect the Touch Pad Connector and remove all screws as shown in Fig. 27 A = M2.5x4 Silver B = M2.5x5 Silver Fig. 27 Top cover 4. Carefully lift up the Top Cover. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 20...

  • Page 21: Removing The Main Board

    1. Remove all connection and screws on main board as shown in Fig. 28 M2.5x5 Silver Fig. 28 Main board 2. Carefully lifting up main board from the rear of the unit as shown in Fig. 29 Fig. 29 Lifting up main board NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 21...
  • Page 22 4. This step only applicable to EasyNote A7. Flip over the main board and release two screws on S-Video Board as shown in Fig. 31 M2x3 Silver Fig. 31 S-video board on Main Board NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 22...

  • Page 23: Removing The Speaker Assembly

    1. Unscrew the screws on the Top Cover as shown in Fig. 33 A = M2x4 Silver B = M2.5x2.5 Silver Fig. 33 Touch Pad 2. Carefully separate the Touch Pad module from Top cover. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 23...

  • Page 24: Dip Switch Settings

    No DIP switch available on ED1 platform. Screws M2.5x2.5 Silver M2.5x4 Silver M2.5x8 Copper M2.5x5 Black M2.5x5 Silver M2.5x6 Silver M2.5x6 Copper M2x7 Silver M2x3 Silver M2x4 Silver M2.5x4 Copper M2.5x3 Silver M2x4.5 Black M4x3 Silver NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 24...

  • Page 25: Notice

    This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from NEC Computers International BV. NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;...

This manual is also suitable for:

Easynote a7

Table of Contents