free stats
Makita 5007MG Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Saw
  5. 5007MG
  6. Instruction manual

Makita 5007MG Instruction Manual

Hide thumbs Also See for 5007MG:

Advertisement

Table of Contents

See also: Instruction Manual

Circular Saw

MODEL 5007MG
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
DOUBLE
INSULATION
M A N U A L
007325

Advertisement

Table of Contents
loading

Related Manuals for Makita 5007MG

Summary of Contents for Makita 5007MG

  • Page 1: Circular Saw

    Circular Saw MODEL 5007MG 007325 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    SPECIFICATIONS Model 5007MG Blade diameter 185 mm at 90° 63.5 mm Max. Cutting depth at 45° 45 mm at 56° 35 mm 5,800 No load speed (min Overall length 317 mm Net weight 4.6 kg Safety class • Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

  • Page 3: General Safety Rules

    GENERAL SAFETY RULES GEA001-3 WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.

  • Page 4: Specific Safety Rules

    19. Store idle power tools out of the reach of chil- erly to minimize body exposure, blade binding, or dren and do not allow persons unfamiliar with loss of control. 000157 the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  • Page 5 jump backwards, but kickback forces can be • Do not use dull or damaged blades. controlled operator, proper Unsharpened improperly blades precautions are taken. produce narrow kerf causing excessive friction, blade binding and kickback. Keep blade sharp • When blade binding, when and clean.
  • Page 6 11. Check the operation of the lower guard spring. 000150 If the guard and the spring are not operating Fig. 2 properly, they must be serviced before use. Lower guard may operate sluggishly due to dam- aged parts, gummy deposits, or a build-up of debris.

  • Page 7: Functional Description

    FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting depth of cut 007326 CAUTION: • After adjusting the depth of cut, always tighten the lever securely. Loosen the lever on the depth guide and move the base up or down.
  • Page 8 • Use only the Makita wrench to install or remove the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the hex bolt counterclockwise. Then remove the hex bolt, outer flange and blade.

  • Page 9: Operation

    To install the blade, follow the removal procedure in reverse. BE SURE TO 007352 TIGHTEN THE HEX BOLT CLOCKWISE SECURELY. When changing blade, make sure to also clean upper and lower blade guards of accumulated sawdust. Such efforts do not, however, replace the need to check lower guard operation before each use.

  • Page 10: Maintenance

    To maintain product SAFETY and RELIABILITY, repairs, any other mainte- nance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1. Brush holder cap...
  • Page 11 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 12 Makita Corporation Anjo, Aichi, Japan 884671-225...

Table of Contents