Index Warning, Caution ..........................English-1 Registration Information .......................English-2 Recommended use ........................English-3 Contents ............................English-5 Quick Start ............................English-5 Controls ............................English-8 Specifications ..........................English-11 Features .............................English-12 Troubleshooting ..........................English-13 TCO Certified Displays 6 ......................English-14 Manufacturer’s Recycling and Energy Information ..............English-15...
Voltage 120* 100* * When operating the AccuSync AS193i monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. NOTE: This product can only be serviced in the country where it was purchased.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information Use the attached specified cables with the AccuSync AS193i(L199ND) color monitor so as not to interfere with radio and television reception.
For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Page 6
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
Contents Your new NEC AccuSync LCD monitor box* should contain the following: • AccuSync LCD monitor with tilt base • Power Cord • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) • Setup Manual • Base Stand •...
3. Connect the 15-pin mini D-SUB of the video signal cable to the appropriate connector on the back of the monitor (Figure B.1). 4. Connect one end of the power cord to the monitor and the other end to the power outlet. Place the Video Signal Cable and power cord to the Cable holder (Figure C.1).
Non-abrasive surface Figure R.1 Figure R.2 Figure R.3 Remove the Base Stand Locking tabs NOTE: Always remove the Base Stand when shipping the LCD. 1. Place monitor face down on a non-abrasive surface (Figure R.1). 2. Using your thumb, press the button to unlock. 3.
Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key OSD Menu Not displaying on Displays OSD. Shortcut to Brightness. Shortcut to Contrast. Selects input signal. screen Displaying on screen Displays OSD menu and Moves leftward.
BRIGHTNESS Adjusts the overall image and background screen brightness. To enter ECO MODE, press the “1 2/RESET” button. ECO MODE OFF: Sets brightness variable to 100% ECO MODE1: Sets brightness to 70%. This setting can adjust brightness to a range in which power is reduced to meet Energy Star measurement conditions. ECO MODE2: Sets brightness to 40%.
OSD TURN OFF The OSD control menu will stay on as long as it is in use. In the OSD TURN OFF submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are 10 - 120 seconds by 5 seconds step.
The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors and are accurate at the time of printing. NEC reserves the right to publish updated carbon footprint values. HDCP(High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).If you are unable to view material via the DVI input, this does not necessarily mean the display is...
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only) •...
TCO Certified Displays 6 Congratulations! This product is TCO Certified – for Sustainable IT TCO Certified is an international third party sustainability certification for IT products. TCO Certified ensures that the manufacture, use and recycling of IT products reflect environmental, social and economic responsibility.
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.