hit counter script
Makita HR5201C Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Rotary Hammer
  5. HR5201C
  6. Instruction manual
Makita HR5201C Instruction Manual

Makita HR5201C Instruction Manual

Hide thumbs Also See for HR5201C:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
INSTRUCTION MANUAL
Rotary Hammer
HR5201C
HR5210C
HR5211C
007857
DOUBLE INSULATION
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1

Advertisement

Table of Contents
loading

Related Manuals for Makita HR5201C

Summary of Contents for Makita HR5201C

  • Page 1 INSTRUCTION MANUAL Rotary Hammer HR5201C HR5210C HR5211C 007857 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    Standard and can, therefore, also be used from sockets Vibration emission (a ) : 12 m/s without earth wire. h,CHeq Uncertainty (K) : 2.5 m/s For Model HR5201C ENG306-1 ENG102-1 Work mode : chiseling function with side grip For European countries only Vibration emission (a ) : 9.5 m/s...

  • Page 3: General Safety Rules

    Do not abuse the cord. Never use the cord for EC-DECLARATION OF CONFORMITY carrying, pulling or unplugging the power tool. Model; HR5201C, HR5210C, HR5211C Keep cord away from heat, oil, sharp edges or We declare under our sole responsibility that this moving parts.

  • Page 4: Specific Safety Rules

    attached to a rotating part of the power tool may parts. This will ensure that the safety of the power result in personal injury. tool is maintained. 13. Do not overreach. Keep proper footing and 24. Follow instruction lubricating balance at all times. This enables better control changing accessories.

  • Page 5: Functional Description

    "OFF" position when released. 2,150 To start the tool, simply pull the switch trigger. Release 2,000 the switch trigger to stop. 1,600 FOR MODELS HR5210C/ HR5201C 1,250 1,075 Trigger switch 007903 CAUTION: Before plugging in the tool, always check to see CAUTION: •...

  • Page 6: Torque Limiter

    This will help prevent pointer points to the symbol. Use a bull point, cold premature wear of the tool. chisel, scaling chisel, etc. For long time hammering (FOR MODELS HR5201C Indicator lamp AND HR5210C ONLY) 1. Power-ON 1. Pointer indicator lamp 2.

  • Page 7: Side Handle

    Side grip The green power-ON indicator lamp lights up when the 1. Side grip tool is plugged. If the indicator lamp does not light up, the mains cord or the controller may be defective. The indicator lamp is lit but the tool does not start even if the tool is switched on, the carbon brushes may be worn out, or the controller, the motor or the ON/OFF switch may be defective.

  • Page 8: Depth Gauge

    007845 1. Depth gauge Bit angle (when chipping, scaling or 2. Clamp screw demolishing) 1. Lock button HR5201C 2. Change lever HR5210C 3. Pointer 007848 The depth gauge is convenient for drilling holes of uniform depth. Loosen the clamp screw and adjust the 007846 depth gauge to the desired depth.

  • Page 9: Maintenance

    Lubrication 007853 CAUTION: This servicing should be performed by Makita • Loosen the six screws with a screwdriver and remove Authorized or Factory Service Centers only. the crank cap. Rest the tool on the table with the bit end This tool requires no hourly or daily lubrication because pointing upwards.
  • Page 10 If you need any assistance for more details regarding Wipe out the old grease inside and replace with a fresh these accessories, ask your local Makita Service Center. grease (60 g). Use only Makita genuine hammer grease SDS-Max Carbide-tipped bits •...
  • Page 12 Makita Corporation Anjo, Aichi, Japan 884701A222...

This manual is also suitable for:

Hr5210cHr5211c

Table of Contents