Page 1
2 mm DC charging connector Transceiver with BL-4S battery pack Talk time Standby Note Up to 5,5 hours Up to 280 Depends on hours network parameters and phone settings ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
16.07.2008 Approved version The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to carry out service to NOKIA products. This Service Manual is to be used only by authorized NOKIA service suppliers, and the content of it is confidential. Please note that NOKIA provides also other guidance documents (e.g.
Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
3. Use only approved components as specified in the parts list. 4. Ensure all components, modules screws and insulators are correctly re–fitted after servicing and alignment. 5. Ensure all cables and wires are repositioned correctly ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
3600 Slide RM-352 Service Manual Level 1&2 4. ESD PROTECTION Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use.
Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications or attachments could damage the phone and may violate regulations governing radio devices. All of the above suggestions apply equally to the product, battery, charger or any accessory. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Batteries’ performance is particularly limited in temperatures well below freezing. Do not dispose batteries in a fire! Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
3600 Slide RM-352 Service Manual Level 1&2 7. EXPLODED VIEW See corresponding ITEM/CIRCUIT REF in the Spare Parts Service Bulletins on NOL. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
For more information, refer to the SS-187 UI flex assembly tool Service Bulletin (SB-011) on NOKIA Online. Supplier or manufacturer contacts for tool re-order can be found in “Recommended service equipment” document on NOKIA Online. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Flash concept – (Point of Sales) To use the FLS-5 Flash Dongle, you have to follow the user guide inside the sales package. Please check always for the latest version of flash software, which is available on Nokia Online. ISSUE 1 Confidential Copyright @ 2008 NOKIA.
2) Remove the F-Cover. 3) Remove the Camera Module with SS-102. 4) Open the first cover clip from the A-Cover with SRT- 5) Open the second cover clip. 6) Remove the A-Cover. ISSUE 1 Confide ntial Copyright @ 2008 NOKIA. All rights reserved...
Page 13
First, insert it only a little under the display, then move Assy. it left and right to begin freeing the glued area. Then push straight down to the middle to remove the display. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 14
13) Open the first side clip. 14) Open the second clip. 15) Lift up the E-Cover slightly. 16) Remove the E-Cover. 17) Separate the Numeric Keymat from the E-Cover. 18) Unscrew the 4 remaining screws. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 15
22) Release the Docking Flex. with the dental tool. 23) Lift up and remove the Docking Flex. 24) Use the dental tool to open the first clip of the Antenna Cover Assy. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 16
26) Open the next clip. 27) Open the next clip. 28) Remove the Antenna Cover Assy. 29) Remove the IHF Speaker. 30) Be careful with the surrounding components when opening the B2B Connector. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 17
31) Separate the PWB from the Slider Module. 32) Remove the UI Flex Assy. 33) If UI-Flex is removed, then a completely new Slider Module must be used for re-assembly. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
3) Align the bottom edge of the slider to the 4) Make sure the guide pins are aligned correctly. bottom edge of the JIG as shown and press down firmly. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 19
5) Smooth down the copper color flex in the 6) Feed the B2B Connector Flex through the Slider direction shown to ensure gluing is complete. Module to reach the end of the assembly. 7) Assembly completed. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 20
There are three areas to clean: the Side Keys/AV Connector/Power Switch. 3) If the D-Cover is new: Remove the gluing foils 4) Insert the AV Connector and press home. and glue areas. ISSUE 1 Confide ntial Copyright @ 2008 NOKIA. All rights reserved...
Page 21
3600 Slide RM-352 Service Manual Level 1&2 5) Carefully bend the power key area into place 6) Bend the side keys into place and press home. and press home. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 22
Slider Module and a itself. correct groundling of the display. 3) Remove the section foil by lifting the red tab to 4) Align the display as shown. expose the glued area. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 23
5) Fix the display in place, use careful even 6) Close the connector. pressure from the sides only to ensure that the display stays fixed. 7) Fold the flex up, away from the display area. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
Page 24
1) Ensure that the Numeric Keymat is fully under the Slider, including back edging. 5: A-Cover and Slider Module 1) Ensure that the Slider Module is correctly inserted under the A-Cover hooks. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...
11.1 Torque information 1) Tighten the screws to the torque of 17 Ncm in the 1) Tighten the screws to the torque of 17 Ncm in the order shown. order shown. ISSUE 1 Confidential Copyright @ 2008 NOKIA. All rights reserved...