Table of Contents
Advertisement
Quick Links
F
C
EDERAL
OMMUNICATIONS
C
(FCC) W
OMMISSION
Instruction to Users
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful in-
terference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio and television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference
by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and the receiver.
- Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/ TV
technician for help.
This equipment has been certified to comply with the
limits for a Class B computing device, pursuant to
part 15 of the FCC rules. Only peripherals (computer
input / output devices, terminals, printers etc.) certified
to comply to the Class B limits may be attached to
this computer. Operation with non-certified
peripherals is likely to result in interference to radio
and TV reception.
Remarks
To meet FCC requirement, shielded cables are required
to connect the device to a personal computer or other
Class B certified device.
Information to Users
Any change or modifications expressly approved by
the party responsible for compliance could void the
user's authority to operate this equipment.
ARNING
DOC N
OTICE
This product conforms to Canadian Class B emissions
regulations.
Ce produit est conforme aux réglements d'émission
Canadienne class B.
E-1
Advertisement
Table of Contents
Related Manuals for Lenovo C92
Summary of Contents for Lenovo C92
- Page 1 EDERAL OMMUNICATIONS (FCC) W OMMISSION ARNING Instruction to Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful in- terference in a residential installation.
-
Page 2: Install The Monitor
INTRODUCTION This microprocessor-based, digital control 19” color monitor is a high performance and easy to use product. It employs the latest on-screen-menu technology. The microprocessor capability offers 12 most commonly used VESA timing modes preset in the factory, and 8 modes for user to adjust to the special timings that user might have. -
Page 3: Control Panel
CONTROL PANEL a. Displays menu & exits menu b. Scrolls through menu to choose an icon for adjustment / Adjusts level of selected icon Confirms menu selection 1. Power LED 2. Power ON/OFF switch... -
Page 4: Using The On-Screen Menu
USING THE ON-SCREEN MENU 1) Display the On-Screen Menu Press the button on the front panel to display the main menu as follows. There is a sub-menu under every option. 2) Select a Sub-Menu Move the cursor by pressing the to select the sub-menu that user's preferred, then press the button to confirm your selection and... - Page 5 3) Color The color temperature of the white image can be adjusted. (1)Use the button to select 9300°K, 6550°K or the user's preferred color. (2)If user color is selected, press the display the "COLOR ADJUST" adjustment screen, then use the adjust the color as desired.
-
Page 6: Troubleshooting
7) OSM Position Change the OSM appearance position using this function. V.POSIT ION V.POSIT ION H.P OSITION F1:QUIT F2:ADJ. Fig.7 TROUBLESHOOTING If your monitor fails to operate functionally, it may be possible to correct the problem by making simple checks as follows: &... -
Page 7: Signal Connector Information
* Note: You can easily distinguish the problem is on the monitor or on the computer by using the monitor’s built-in selftest function. With the monitor power ON, disconnect the signal cable from monitor. If you see a “NO SIGNAL” image on the screen, (shown below) the monitor is function properly, and the problem is at PC side, or signal cable. -
Page 8: Technical Specifications
TECHNICAL SPECIFICATIONS " 9 - i t - i t i l i *Specifications are subject to change without notice. PRESET MODES ; " , s i - i t...