Canon VB-M740E Installation Manual
Hide thumbs
Also See for VB-M740E:
- Operation manual (287 pages) ,
- Manual (260 pages) ,
- Installation manual (4 pages)
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Network Camera
Installation Guide
/
Please be sure to read the "Safety Precautions" section for correct use. After reading this
Installation Guide, keep it in a readily accessible location for future reference.
* Some cameras are not available in certain countries or regions.
Caution
Request a professional installer for all installation work. Never try to install the
camera yourself. Doing so may result in unforeseen accidents such as dropping
the camera or electric shock.
Check Included Items
Camera, Screws (M4) x 4
Template
Installation Guide (This document)
Setup CD-ROM
Warranty Card
Ceiling Plate
Notice
Dedicated wrench
Safety Wire, Screws (M3) x 1
I/O Interface Cable (BK2-0035-000)
Power Interface Cable
Symbols Indicating Camera Model
Camera specific functions will be listed using the symbols below.
: VB-M741LE
: VB-M740E
Accessories
The following accessories can be purchased separately as necessary. Some accessories are not
available in certain countries or regions.
Conduit Box CB740-VB
Dedicated accessory used to protect wiring cables that cannot be stored above the ceiling. This can
be attached to the composite pipe.
Pendant Mounting Kit PC640-VB
Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings,
such as in big-box stores.
Canon AC Adapter PA-V18
Dedicated AC adapter for this camera.
© CANON INC. 2016
Part Names
6
7
8 9
10
1
2
5
11
12
3
4
13
Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
18
14
15 16 17
1. Lens protector / 2. Screw hole for attaching / 3. LED (Orange) / 4. LED (Blue)* / 5. Notched cap /
6. Power connection terminal
/ 7. External device I/O terminals
/
8. Audio input terminal (Black) (common LINE IN and MIC IN)
/
9. Audio output terminal (White) (LINE OUT)
/ 10. 100Base-TX LAN connector
11. Pan axis adjustment screw / 12. Tilt axis adjustment screw /
13. Rotation axis adjustment screw / 14. Memory card slot / 15. Reset switch / 16. LED (Blue)* /
17. Reboot switch / 18. Memory card cover
* On: when powered on, during reboot, during normal use / Off: when [Turn Off] is selected
(please refer to the "Operation Guide")
The contents of this guide are subject to change without any prior notice.
BIE-7155-000
ENGLISH
External Dimensions
60 (2.36) 60 (2.36)
4-M4
(*1, *2)
Camera mounting
tab slots
Screw hole for attaching
214 (8.43)
102 (4.02)
85.7 (3-3/8)
(*3, *4)
83.5 (3-9/32)
(*4)
7.0 (0.28)
46.0 (1-13/16)
(*4)
4-M4
(*7)
Camera
mounting tabs
Unit: mm (in.)
Before Installing the Camera
Set the IP address and other network information on the camera using the "Camera Management
Tool" on the Setup CD-ROM.
Printed in Japan
For details on how to operate the "Camera Management Tool", please refer to the "Camera
Management Tool User Manual".
Using a Memory Card
Loosen the screws with the dedicated wrench, open the
memory card cover, and then place the memory card in
the memory card slot. Once the memory card is in place,
close the memory card cover and tighten the screws
with the dedicated wrench.
To remove the memory card, push it in all the way until
the card slightly pops out and remove.
Important
• Insert a memory card before installing the camera.
• When using a memory card with the camera for the first
time, it is recommended to format the card after inserting
it into the camera (please refer to the "Operation Guide" >
"Setting Page" > "Memory Card").
• Always unmount the memory card before removing it
Memory card slot
(please refer to the "Operation Guide" > "Setting Page" >
"Memory Card").
Once this has been completed, close the memory card cover and tighten the screws with the
dedicated wrench.
Installing the Camera
1
Directly attached to ceilings/Directly attached to walls
1 -1
1 -2
Ceiling Installation
a
a
Wall Installation
a. Template
1 -3
b
b. Ceiling Plate
If the cables cannot be stored above a ceiling
If the cables cannot be stored above the ceiling,
such as with concrete ceilings, remove the notched
cap at the camera joint section with the dedicated
wrench, and create an opening for the cable to pass
151 (5.94)
through.
The cables can be stored with the use of the conduit box
CB740-VB (sold separately), which can also be attached
to the composite pipe. Please refer to the installation guide
included with the conduit box for the installation method.
288 (11.34)
Unit: mm (in.)
Attaching to a junction box
Attach the ceiling plate to the junction box after confirming the
fixing holes locations with the external dimensions diagram.
*1 Ceiling plate mount holes
Ceiling pendant mounting
*2 Option unit mount holes
*3 Ceiling/Wall mount holes position
Mount using the Pendant Mounting Kit (sold separately).
*4 Junction box fixing holes position
For details please refer to the Installation Guide included with the kit.
*5 Ceiling/Wall mount holes
*6 Junction box fixing holes
1 -1
*7 Camera mounting holes
2.5 cm (1.0 in.)
Pass necessary cables for
connecting the camera through
the pipe.
2
❸
Note
Pass the safety wire through
the slit
and attach it to the
hook on the rear side
.
c. Safety wire
3
d
e
d. I/O interface cable
e. Power interface cable
4
b
Dedicated
wrench
6
Notched
cap
Adjusting the pan axis
1 -2
❷
❸
❶
Adjusting the tilt axis
M3*
❹
* Included
M4* × 4
with Pendant
Mounting Kit
❷
❷
Adjusting the rotation axis
Dedicated
wrench
c
❶
M3
Screws (included)
❶
7
When the installation has finished, please adjust the angle using the "Camera Angle Setting
Tool", found in the Setup CD-ROM.
When the temperature within the camera is low (heater activated)
When the unit is powered by a 24 V AC/ PoE+ power source, the heater unit can be used.
The heater unit's orange LED will turn on, when the unit has been activated due to the low
Note
temperature within the camera, and the transfer of video is also not possible.
Completely wrap the cable connection with
Once the temperature within the camera has reached the level where it can transfer the video
waterproof tape to the cable jacket, so as not
once again, the orange LED will turn off.
to allow water to enter between the individual
cables.
5
M4 × 4
Screws
(included)
Dedicated
wrench
Use the dedicated wrench to adjust the
following three rotation axes to set the angle.
Note
Set the angle so that the memory card
cover is at the bottom.
❺
❶
❷
❹
❸
❹
❶
❸
Note
Shake the unit after tightening the screws. If the joint
section appears to wobble, further tighten the screw.
❸
❷
Advertisement
Related Manuals for Canon VB-M740E
Summary of Contents for Canon VB-M740E
- Page 1 *6 Junction box fixing holes 1 -1 1 -2 such as in big-box stores. *7 Camera mounting holes ❷ ❹ Canon AC Adapter PA-V18 Camera mounting tabs Unit: mm (in.) Dedicated AC adapter for this camera. ❸ ❸ Before Installing the Camera Set the IP address and other network information on the camera using the “Camera Management...
- Page 2 Remove the power connector attached to the AC adaptor, then connect the power interface cable continue connecting the cable. canon-europe.com/weee, or www.canon-europe.com/battery. from the power connector included in the package, as shown in the following diagram. Wrap the • Do not disassemble or modify the camera.