C H A P T E R 25 Configuring Igmp Snooping And Filtering - Cisco Catalyst 4500 Series Configuration Manual
Release ios xe 3.3.0sg and ios 15.1(1)sg
Hide thumbs
Also See for Catalyst 4500 Series:
- Software configuration manual (2086 pages) ,
- Administration manual (1814 pages) ,
- Configuration manual (1254 pages)
Table of Contents
Advertisement
About IGMP Snooping
IGMP Snooping Querier, page 25-4
•
Explicit Host Tracking, page 25-4
•
Quality of service does not apply to IGMP packets.
Note
IGMP snooping allows a switch to snoop or capture information from IGMP packets transmitted
between hosts and a router. Based on this information, a switch adds or deletes multicast addresses from
its address table, which enables (or disables) multicast traffic from flowing to individual host ports.
IGMP snooping supports all versions of IGMP: IGMPv1, IGMPv2, and IGMPv3.
In contrast to IGMPv1 and IGMPv2, IGMPv3 snooping provides immediate-leave processing by default.
It provides explicit host tracking (EHT) and allows network administrators to deploy SSM functionality
on Layer 2 devices that support IGMPv3. See the
subnets where IGMP is configured, IGMP snooping manages multicast traffic at Layer 2. You can
configure interfaces to dynamically forward multicast traffic only to those interfaces that are interested
in receiving it by using the switchport keyword.
IGMP snooping restricts traffic in MAC multicast groups 0100.5e00.0001 to 01-00-5e-ff-ff-ff. IGMP
snooping does not restrict Layer 2 multicast packets generated by routing protocols.
Note
For more information on IP multicast and IGMP, refer to RFC 1112, RFC 2236, RFC 3376 (for
IGMPv3).
IGMP (configured on a router) periodically sends out IGMP general queries. A host responds to these
queries with IGMP membership reports for groups that it is interested in. When IGMP snooping is
enabled, the switch creates one entry per-VLAN in the Layer 2 forwarding table for each Layer 2
multicast group from which it receives an IGMP join request. All hosts interested in this multicast traffic
send IGMP membership reports and are added to the forwarding table entry.
Layer 2 multicast groups learned through IGMP snooping are dynamic. However, you can statically
configure Layer 2 multicast groups using the ip igmp snooping static command. If you specify group
membership statically, your setting supersedes any automatic manipulation by IGMP snooping.
Multicast group membership lists can contain both user-defined and IGMP snooping settings.
Groups with IP addresses in the range 224.0.0.0 to 224.0.0.255, which map to the multicast MAC address
range 0100.5E00.0001 to 0100.5E00.00FF, are reserved for routing control packets. These groups are
flooded to all forwarding ports of the VLAN with the exception of 224.0.0.22, which is used for IGMPv3
membership reports.
If a VLAN experiences a spanning-tree topology change, IP multicast traffic floods on all VLAN ports
Note
where PortFast is not enabled, as well as on ports with the no igmp snooping tcn flood command
configured for a period of TCN query count.
For a Layer 2 IGMPv2 host interface to join an IP multicast group, a host sends an IGMP membership
report for the IP multicast group. For a host to leave a multicast group, it can either ignore the periodic
IGMP general queries or it can send an IGMP leave message. When the switch receives an IGMP leave
message from a host, it sends out an IGMP group-specific query to determine whether any devices
connected to that interface are interested in traffic for the specific multicast group. The switch then
updates the table entry for that Layer 2 multicast group so that only those hosts interested in receiving
multicast traffic for the group are listed.
Software Configuration Guide—Release IOS XE 3.3.0SG and IOS 15.1(1)SG
25-2
Chapter 25
Configuring IGMP Snooping and Filtering
"Explicit Host Tracking" section on page
25-4. In
OL-25340-01
- Quick Links:
- Resetting a Switch to Factory Default...
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
