Table of Contents
Advertisement
Table of Contents
- - - - - - - - - - - - - - - - - - - - - - - 2
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - 4
Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Adjusting measuring reference / tripod - - - - - - - - - - - 4
Multifunctional endpiece- - - - - - - - - - - - - - - - - - - - - - 5
Distance unit setting - - - - - - - - - - - - - - - - - - - - - - - - 5
Tilt unit setting- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Timer (automatic release) - - - - - - - - - - - - - - - - - - - - 5
Beep ON/OFF- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Illumination ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - 6
Keypad lock ON - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Keypad lock OFF - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Measuring single distance - - - - - - - - - - - - - - - - - - - - 7
Permament / Minimum-Maximum measuring - - - - - - - 7
Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
Area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Volume- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - 10
Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - 10
Pythagoras (partial height) - - - - - - - - - - - - - - - - - - - 11
Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Smart Horizontal Mode - - - - - - - - - - - - - - - - - - - - - 13
Height tracking - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Leveling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
- - - - - - - - - - - - - - - - - - - 7
Memory (20 last displays) - - - - - - - - - - - - - - - - - - - -14
Delete Memory - - - - - - - - - - - - - - - - - - - - - - - - - - -14
Calibration of tilt sensor (Tilt Calibration) - - - - - - - - -15
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -17
Areas of responsibility - - - - - - - - - - - - - - - - - - - - - -17
Permitted use - - - - - - - - - - - - - - - - - - - - - - - - - - - -18
Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - -18
Hazards in use - - - - - - - - - - - - - - - - - - - - - - - - - - -18
Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - -18
Disposal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -18
Electromagnetic Compatibility (EMC) - - - - - - - - - - - -18
FCC statement (applicable in U.S.) - - - - - - - - - - - - -19
Laser classification- - - - - - - - - - - - - - - - - - - - - - - - -19
Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Makita LD080PI
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -15
- - - - - - - - - - - - - - - - - - - - - - - - -16
- - - - - - - - - - - - - - - - - - - - - - - -17
- - - - - - - - - - - - - - - - - - - - -17
EN
1
Advertisement
Table of Contents
Related Manuals for Makita LD080PI
Summary of Contents for Makita LD080PI
-
Page 1: Table Of Contents
Height tracking - - - - - - - - - - - - - - - - - - - - - - - - - - - 13 Leveling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14 Makita LD080PI... -
Page 2: Instrument Set-Up
Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. Timer Area / Volume / Pythagoras/ Inclination Stake out functions Measuring Clear / Off reference / Units Memory Makita LD080PI... -
Page 3: Display
Timer Stake out batteries. Change batter- ies when battery Measuring Memory symbol is flash- reference ing. Circumfer- ence Pythagoras Angle Horizontal Wall area measurement Min/Max Indirect height Measuring Addition / Units Subtraction Main line 2nd result Makita LD080PI... -
Page 4: Operations
OFF. fault operation tomatically. mode. Adjusting measuring reference / tripod Distance is measured from the tripod thread Distance is measured from the front of the device. permanently. Distance is measured from the rear of the device (standard setting). Makita LD080PI... -
Page 5: Multifunctional Endpiece
The de- layed release is recommended for precise aiming e.g. at long distanc- Adjust delay of au- es. It avoids shaking of the device tomatic release when pressing the measurement (max. 60 sec, key. standard setting 5 sec) Makita LD080PI... -
Page 6: Beep On/Off
Operations Beep ON/OFF Illumination ON/OFF 2 sec 2 sec simultane- simultane- ously ously Keypad lock ON Keypad lock OFF 2 sec within simultane- 2 sec ously Makita LD080PI... -
Page 7: Measuring Functions
The same process can be The next meas- The next meas- used for adding or subtracting urement is added urement is sub- areas or volumes. 5.515 7.332 to the previous tracted from the 12.847 one. previous one. Makita LD080PI... -
Page 8: Area
Measuring Functions Area The result is shown in the main line and the measured value above. Aim laser at first Aim laser at sec- 24.352 target point. ond target point. 2 sec 19.823 Circumference 24.3 52 Area Makita LD080PI... -
Page 9: Volume
Aim laser at sec- Aim laser at third target point. ond target point. target point. The result is shown in the main line 80.208 Circumference and the 2 sec measured 208.70 3 value above. Wall areas 78.694 78.6 94 Volume Makita LD080PI... -
Page 10: Pythagoras (2-Point)
Pythagoras (3-point) Aim laser at up- Aim laser at rec- Aim laser at lower point. per point. tangular point. Notice additional Pythagoras measurement in- formation at the bottom of the next page. 8.294 Makita LD080PI... -
Page 11: Pythagoras (Partial Height)
In order to obtain the best results we recommend to use a tripod or to flip out the corner end piece. • Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement. Makita LD080PI... -
Page 12: Stake Out
The distance to beep. the next stake The function can be stopped 0.625 0.240 m is missing out point is dis- by pressing the CLEAR/OFF up to next 0.625 m played. 0.24 0 button. distance. Makita LD080PI... -
Page 13: Smart Horizontal Mode
The tracked height "y" is in 90° to the 1st 6.932 aimed point "x". 30.2 ° = Tracking angle 9.82 7 Stops Height tracking and = Tracking height displays last measurement. Makita LD080PI... -
Page 14: Leveling
Memory (20 last displays) Delete Memory 2 sec 2 sec The value from 20 last displays simultaneously Navigates trough the main line can are displayed. 20 last displays. 8.294 8.294 be used for fur- Memory is completely de- ther calculations. leted. Makita LD080PI... -
Page 15: Calibration
After 2 sec the device 180° goes back to the nor- mal mode. Turn the device horizontally by 180° and place it again on absolutely flat surface. Makita LD080PI... -
Page 16: Technical Data
117 x 57 x 32 mm 4.6 x 2.4 x 1.3 in Weight (with batteries) 0.14 kg / 4.938 oz Temperature range: - Storage -25 to 70 °C -13 to 158 °F - Operation -10 to 50 °C 14 to 122 °F Makita LD080PI... -
Page 17: Message Codes
Areas of responsibility number, press the Clear button and Responsibilities of the manufacturer observe the following instructions: of the original equipment: Cause Correction Makita Corporation Anjo, Transverse tilt Hold the instrument Aichi 446-8502 Japan greater than 10° without any transverse Internet: www.makita.com tilt. -
Page 18: Permitted Use
The device conforms to the most stringent • Aiming directly in the sun sion hazardous areas or in aggressive requirements of the relevant standards environments. and regulations. Yet, the possibility of causing interference in other devices cannot be totally excluded. Makita LD080PI... -
Page 19: Fcc Statement (Applicable In U
CAUTION receiver is connected. Looking into the laser beam may be • Consult the dealer or an experienced hazardous to the eyes. radio/TV technician for help. Subject to change (drawings, descriptions and technical data) without prior notice. Makita LD080PI...